Search Documents

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By Alexandra P. Wright

A vital aspect of environmental impact assessment for surface mining operations is the determination of potential effects on water resources. This topic has been the subject of much recent concern, controversy and legislation. As increasing data become available regarding the types of hydrologic effects that may be anticipated, methods for safe guarding our water resources can be refined. In view of our current energy situation, the need to develop coal re- sources in a timely and economic manner is apparent. The challenge to the mining industry is to develop these resources in a manner that is also compatible with the beneficial use of water resources in mining regions. For this reason, thorough evaluation of the hydrology of potential mining areas in consideration of proposed mining processes and relevant legal criteria is essential. While pre-mining hydrologic investigations often suggest generalized potential effects, a more reliable method for evaluating specific potential effects is to establish and maintain a hydrologic monitoring program. Such a program must be carefully designed to suit the specific project and its location. This paper describes an approach for selection of criteria for designing a monitoring program for a proposed coal surface mining operation and gasification plant in southwest North Dakota. Woodward-Clyde Consultants (WCC), recently prepared an environ- mental impact report for the ANG Coal Gasification Company (ANG), a subsidiary of the American Natural Gas Company. The mining will be carried out by The North American Coal Corporation (NACCO). Preparation of the report provided the opportunity for the development of a sensitive and economical monitoring program which would function as a baseline hydrological data gathering network as well as act an an early detection system for hydrologic effects of the proposed mining.

Jan 1, 1975

A knowledge of airway friction factor (K-factor) is necessary to designing mine ventilation systems for least cost and optimum effectiveness. The friction factor used must be accurate and reliable to estimate correctly roadway resistances and pressure sources for required flows. Though the resistance to flow offered by mine airways has been an object of study over the last half century, no accurate relation has yet been established from which the prediction of the resistance of a projected airway can be made. In Kentucky, only limited and incomplete data on local K-factors are available. Therefore, there is a need for field investigations to determine these values in-situ for existing mining conditions. The author describes a study concerning K-factor that was carried out in ten coal mines, located in eastern and western Kentucky. The results of these investigations are presented in both tabular and graphical form.

Jan 1, 1991

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998

By Andrea Brickey, JUDITH BUABA, RICHARD AMOAKO

The global mining industry has recorded significant declines in accident and injury rates attributed to the advancement in technology, increased enforcement, and safety consciousness. A goal of the mining industry is to achieve zero injury and occupational illness on all mine sites, prompting increased research into ways to further reduce mine accidents. A machine learning technique known as multiclass logistic regression is applied on a 10-year injury dataset from the Mine Safety and Health Administration (MSHA) to determine a miner’s susceptibility to a class of injury and to help identify significant risk factors associated with different classes of injury. The data is aggregated based on injury classification to provide statistically relevant results. The analysis identifies specific risk factors that influence a mine worker’s susceptibility to a given class of injury, i.e., non-fatal with no days lost or restricted activity, non-fatal with days lost and/or days of restricted work activity, and fatal and total permanent or partial permanent disability. These factors include miner’s age, mine type (coal vs. non-coal), experience on the current job (years), shift start time, employment type (operator vs. contractor), mining district, and type of accident. The results of the analysis indicate that a miner’s experience on the job, i.e., the number of years worked in a current job, is a significant risk to injury occurrence, even for those with decades of total mining experience. We further show the differences and similarities between the surface and underground mine incidents.

Nov 3, 2020

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By N. I. Aziz, I. Tague, P. Mackenzie-Wood

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Feb 24, 1997

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By C. Widham

Introduction It is generally accepted as dogma that sampling contributes most of the error in gold fire assays. Differences in assay results on pulps from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" of relatively coarse gold particles. It is true that coarse gold particles can contribute to substantial sampling fluctuations. But, while the process of sampling is probably the major source of error, the analytical process cannot be completely ignored as a possible contributor to erratic assay results. To maintain a stable assay process, the analytic part of the system must also be kept in control. One method of monitoring the performance of the analytic system is to systematically assay standard materials, whose sampling characteristics are carefully controlled. Gold assay standards are not prepared, nor can they be prepared, to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for both preparation (i.e., comminution and splitting) and fire assaying and then come to conclusions only about the fire-assay process. Because most gold ores are very heterogeneous, sampling errors would, in most cases, completely mask the contribution of the analytical errors. Assay-standard material is prepared only to assess the accuracy and variability in the fire assay process. Because the objective of the assay standard is to provide information about the fire assaying, it is necessary to control the sampling error of the standard material, so that it is only a minor constituent of the discrepancies observed in any assay results. To do this requires that the particle size of the standard material be reduced to a point where the relative standard deviation of the sampling error (i.e... the standard deviation of the errors divided by the average gold content of the material) is 2% or less. For all but very homogeneous mineralization, this means that the material must be reduced to 100% -150 mesh before the sampling errors are adequately controlled. However, even reducing the particle size can contribute to sampling problems. The liberation of gold may cause segregation that can cause large sampling fluctuations that are not easily controlled while maintaining the desired grade. Because, in most cases, the standard material would already be in the "pulp" state when it is submitted to a lab for assay, it is not possible to entirely conceal the nature of the sample from the lab. This is a problem inherent in using assay standard material. Because of the contribution of sampling to error generation in the assay process, the use of "coarse" material does not solve the problem of submitting a totally "blind" standard to the lab. In the sections that follow, the selection, preparation, testing and use of gold fire assay standard material is discussed. While some may dismiss the production of standard material as folly, it is possible to produce and utilize standard material to stabilize and improve the fire-assay process to produce more reliable assay results. Material selection It is desirable to use material that has as nearly the same metallurgical characteristics as the samples with which the standards will be included. However, this is usually difficult. For many reasons, including the particle size at which a significant amount of the gold mineral is liberated, the sampling characteristics of even -150-mesh material may preclude the use of geologically and metallurgically similar ore as a standard. It is usually easier to get material having desirable grade characteristics with the necessary sampling properties than it is to find geologically and metallurgically similar material with the required sampling characteristics. High-grade standards are especially difficult to find and prepare. This is because, as grade increases, the size of the gold particles usually increases. Larger gold particles are liberated and tend to segregate during comminution, and the homogeneity of the material cannot be maintained. For grades much above 3 g/t (0.088 oz/ton), it is very difficult to find material that has the proper sampling properties. Old mill tailings are likely candidates for assay standards. Some of these have sufficiently homogeneous mineral contents, so that the sampling errors can be effectively controlled. Where mill tailings are either not available or are not acceptable, mineralization that has exhibited homogeneous results in reassays of the pulp material is also a good candidate for the standard. Finally, the mineralized rock being sampled may (and should) be used if adequate homogeneity in the -150mesh material exists. "Adequate" ("acceptable") homogeneity is defined below.) It is important to use standards having a wide range of grades. This alone may preclude the material being

Jan 1, 1997

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or 'greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By William C. Peters

The Alpine-Himalayan system, the only major active tectonic belt mainly exposed in a continental mass, is of increasing interest to exploration geologists as well as to theoreticians. Answers to the broader problems of plate tectonics are being sought in this intricate system where the geosynclinal concept was born and where the geotectonic cycle was first applied to metallogeny. The search is all the more intense because it involves scientists from more than a dozen countries with a stimulating variety in perspective. The international Geodynamics Project has allocated the Alpine-Himalayan system to two separate study groups with one directing its attention to the Alpine-Mediterranean region and the other giving consideration to the Himalayan region. This geographic division is accepted in this paper, with remarks being confined to the former and to the west of boundary zone between the European-Asian and the Southeast Asian plates as envisioned by Dewey and Bird (1970). The region is well-mapped in some parts and it includes some of the most intensely-studied geology, most classic mines, and newest orebody discoveries. Within the region, an Alpine-age copper-molybdenum metallogenic belt extends from Rumania to Pakistan. The belt can be considered in terms of plate tectonics, and there is the possibility of using plate tectonics concepts in exploration.

Jan 1, 1973

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By D. M. Abbott

The problem with best practices occurs when they do not work. This happens when the seldom-stated assumptions underlying the practice are not met. This paper provides some examples for the mining industry: (1) when core splitting is inappropriate, (2) when the use of fire assays for placer samples is inappropriate, and (3) when high-grading may be acceptable. Geologic conclusions are, in the final analysis, expressions of judgment predicated upon knowledge and experience. A geologic conclusion, however, purports to be more than an arbitrary determination—it is reached as a consequence of method. No specific method is required, but the method used must be an orthodox method, in accordance with orthodox definition of terms, and the one best adapted to the dealing with the questions asked about the property in question. Whether the so-called “best practice” is really applicable to the job at hand must be decided on the basis of professional scientific judgment. When one decides to deviate from a published “best practice” for sound scientific reasons, describe in detail in the report what the so-called “best practice” is, why it was inappropriate for the project, and why the method used was better. If one becomes aware that a “best practice” is being proposed, actively urge those proposing it to include in its description the underlying assumptions that must be met in order for the “best practice” to be valid.

Jan 1, 2014

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By J. Gathje

Normal process development for pressure preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests, followed by operation of a continuous autoclave pilot plant for confirmation of the various process options. This scheme will generally provide good information showing the effects of such variables as grind size, time, and temperature, and will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several recent test programs conducted over the last three to four years have shown that the cyanide leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot plant autoclave. Examples are provided to demonstrate these differences and to show the importance of extending the laboratory investigations to include the use of a semicontinuous autoclave test procedure. A test case is cited in which this procedure provided data that could not be obtained from batch tests.

Jan 1, 1995