Search Documents

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980&apos;s. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986

By J. E. Gebhardt, S. Chander

Significant advances have occurred in the use of electrochemical techniques for sulfide mineral flotation research. The techniques have been used singly or jointly with other characterization methods. When used in combination with other methods, the electrochemical methods provide a means to control the state of oxidation of the surface. Various analytical methods are employed for characterization. The methods that have been used include wetting, x-ray photoelectron and fourier transform infrared spectroscopies. The electrochemical methods include voltammetry and transient electrochemical techniques of galvanostatic polarization and AC impedance spectroscopy. The challenge for the future lies in the utilization of this knowledge in plant operations so as to increase the overall efficiency of flotation separations.

Jan 1, 1989

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By O. Guyot, T. Mulpeter

Sadiola Hill mine is located in the sub-Saharan part of Mali. In its first two years of operations, Sadiola Hill mine had already exceeded expectations with respect to profitability, plant capacity, metallurgical recovery, cash costs and social integration into the area. The advanced control system installed by the authors has been a major contributor in the substantial throughput of the mill over the design tonnage with no loss of recovery. The run-of-mine ore at Sadiola consists of soft clays with a varying percentage of grit, producing a high viscosity slurry. The percentage of grit fed to the plant varies on an hourly basis. This combination was expected to have a large impact on the milling circuit and determined that the early installation of an expert mill control system would be advantageous. Svedala Cisa OCS©, was selected as the most suitable support software. The operational rules and control philosophy are housed in the OCS© graphic-oriented fuzzy expert system while a model­based Soft Sensor has the remarkable ability to detect the variations in grit in the feed. Designed during the second half of 1996, commissioning of the system began in March 1997, the OCS was fully on-line by September. With the implementation of the optimising control strategy a throughput of 5.0 million tons relative to the target of 4.4 million tons was achieved for the 1998-operating year. The Sadiola project confirms that advanced process control techniques are among the most cost-and time-effective methods of improving metallurgical plant performance. The recipe that worked at Sadiola is a mix of metallurgical expertise, proper software selection, adequate design of control philosophy, and excellent plant support and follow­up. The early decision, design and installation of the mill control system has resulted in an enhanced Return on Investment.

Jan 1, 2000

Mines in the Lake Macquarie region of New South Wales, Australia, are faced with the dilemma of having to introduce longwall mining techniques at a time when increasingly large areas of the surface are being used for urban development. Increasing pressures on safety, costs and productivity performance dictate that longwall mining is the method for the future. Construction of surface structures is controlled by a statutory body known as the Mine Subsidence Board (MSB). All surface structures have to be designed to MSB criteria. All mining plans involving secondary excavation also have to be submitted to the MSB for approval. The Board acts as risk assessor in evaluating acceptable levels of surface subsidence vs. the value of the coal resource. Surface repairs are paid for by a levy on all coal producers.

Jan 1, 1995

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By R. Sandrik

Northwestern Resources Co. (NWR) was established in 1972 as a wholly-owned subsidiary of Western Energy Company of Butte, Montana, to acquire, explore, develop, and produce energy resources outside the state of Montana. Western Energy is a coal mining company with successful operations in Montana and Wyoming. In 1974, NWR acquired its first lignite lease in Texas. NWR eventually acquired a large leasehold in central Texas, which was identified as having a high potential for future production. In 1979. NWR contracted to supply lignite to Utility Fuels, Inc. (UFI), a fuel affiliate of Houston Lighting and Power Company (HL&P). This project, together with leases held by UFI, became the Jewett Mine. Lignite from the Jewett Mine is used as fuel at the adjacent HL&P Limestone Electric Generating Station, at an annual rate of approximately 7.3 Gkg (eight (8) million tons) per year.

Jan 1, 1991

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By Nikhil Dhawan, Shrey Agrawal, Ashwini Kumar

The current study investigates sericite clay as an alternative source of potash and alumina. The alumina and potash content in the sericite is approximately 35 and 10%, respectively, compared with 50–55% in bauxite ore. Muscovite and illite phases are stable, and direct leaching is found to be ineffective. Here, planetary ball milling was performed, which provided dissociation of stable phases to relatively reactive phases. The milling led to a five-fold increase in the surface area, resulting in enhanced leaching kinetics even at low acid concentration. The statistical design obtained optimal conditions of 8 h of milling followed by leaching in 1.73 M HCl at 75 °C, yielding 82% alumina extraction in precipitate with 85% purity in γ-alumina form and 63% potassium dissolution in sylvinite phase. The yield of the precipitate was ~65–68%, and the acid leach residue contained primarily silica.

By Göksel Hızlı, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

The carbothermic reduction of celestite is the first step in producing many strontium products. The way materials move in the rotary kiln has an essential effect on the carbothermic reduction efficiency as well as the temperature. In this study, the reduction of celestite ore and excess carbon blend in a laboratory-scale rotary kiln was investigated. In the experiments carried out at three different temperatures, the rotational speed and slope of the furnace tube were altered, and their effects on the reaction efficiency were examined. The leachability of the reduced powders and the content of the unburned coke indicated the optimal parameters for the reaction.When the speed was increased to 10 rpm, the powders weremoremobile in the stack and could react more easily with the furnace atmosphere. According to the results, celestite can be reduced by carbon at temperatures of 1000–1200 °C, at rates of between 5% and 75%. The maximumreaction yield (75%) was obtained with a slope of 2° and a rotational speed of 6 rpm at 1100 °C.

May 7, 2020