Search Documents

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By Glenn J. Phillips, Debra L. Musick

The operating mine is dynamic, everchanging, and a continuous moving target. The only way to effectively manage such a creature is to be able to evaluate the cost of operation over short enough time periods that rapid effective controls can be implemented before loss can erode the marginal profits in todays market place. Such short term evaluations can provide the basis for the long range planning that can keep an operation healthy in the future. The spreadsheet programs on small computers (PC's) offer the possibility of such evaluation by accumulating data in a useable format, providing timely cost reporting and providing a tool for use in evaluating the day to day alternative choices of the real mining world.

Jan 1, 1987

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By Art Hamid, Manfred Wong, Carlos Jaramillo, Greg Raines, John Caulfield

"The Central Bayside System Improvement Project (CBSIP) is a critical element of the Sewer System Im-provement Program (SSIP), a 20-year, $6.9-billion investment by the San Francisco Public Utilities Commis-sion (SFPUC) to upgrade San Francisco’s 100+ years old seismically vulnerable combined sewer system. The CBSIP’s centerpiece, a proposed 10,000-foot-long (3,048-meter-long) Channel Tunnel, will provide reliable and redundant gravity conveyance and storage of combined wastewater flows from the northern and central parts of San Francisco to the Southeast Water Pollution Control Plant (SEP) while ensuring compliance with regulatory requirements for combined sewer discharges to the Bay. A tunnel with a diameter of 23 to 30 feet (7 to 9 meter) is being planned using pressurized-face tunnel boring machine technology. Project challenges include tunneling through Franciscan Bedrock, mixed ground conditions in close proximity to the Bay, connector tunnels and shafts, construction in congested urban environment, and challenging real estate issues for shaft access. BACKGROUND AND NEED FOR TUNNEL The City of San Francisco is one of the most beautiful cities in the world. About 850,000 people live in the city and many more come to work, for tourism, and for attending conferences. The SFPUC is a department of the City and County of San Francisco that provides energy, drinking water and wastewater services to San Francisco, wholesale water to three Bay Area counties, and green hydro-electrical and solar power to San Francisco municipal departments. The SFPUC wastewater system includes tunnels, large storage/transport boxes, 1000 miles of collection sewers, 28 pump stations, and three wastewater treatment plants. San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. After decades of service, much of the sewer system is nearing end of its working life. During the 1989 Loma Prieta earthquake, damage to SFPUC water and wastewater infrastructure was extensive. The 11,200-foot-long (3,400-meter-long), 66-inch-diameter (1,676-mm-diameter) Channel Force Main, built in 1976, and a critical component of the SF wastewater system was also damaged. This force main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the SEP. The force main is at the end of its life and was not constructed to the current seismic code; in addition it has no redundancy. Figure 1 shows the project background and the force main that will be provided redundancy by the new gravity tunnel."

Jan 1, 2016

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998

By Paul I. Eimon

Mineral exploration involves the selective collection, organization, evaluation, and interpretation of geologic and economic data. The sources for such data are original field observations and existing documented information of various types (publications, reports, maps, company files, etc.). As exploration data are accumulated, their storage, organization, indexing, and J retrieval is key to exploration progress. Initial use of computers by mineral exploration groups indicates that data can be meaningfully handled by machines. A computer system makes possible: 1) the storage, manipulation, collation, and selective retrieval of data; 2) the utilization of data banks developed by geologic service groups and available at relatively low cost; and 3) the retrieval of stored data more rapidly, completely, and effectively than by manual systems. Profitable utilization of these capabilities is conditioned by several factors, particularly by the information selected for the system data base and by the design of the computer system itself.

Jan 1, 1968

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

The mining and minerals extraction industries have often been demonized by the public as industries that put profits and production before people. It is true that the inherent danger of the work has led to more fatal accidents than anyone associated with the industry would care to remember. But, in stark contrast to what has often been said, the truth of the matter is safety is now the top priority of every miner, from the face of the longwall to the executive boardroom. Without safety, nothing else matters. This message was told and retold by representatives from some of the world?s top mining and petroleum companies from Oct. 11-13 during the inaugural Safety and Reliability in the Mining and Resources Industries Conference in Calgary, Canada. The meeting was hosted jointly by the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) and the Society for Mining, Metallurgy, and Exploration (SME). It was the first of a series of conferences to focus on these important topics. Next year, the conference will be held in Minneapolis, MN from Nov. 13-15.

Jan 1, 2011

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By Marvin P. Barnes

An attempt has been made to compile and code geologic data relating to twenty of the major porphyry copper districts of North America in such a manner as to permit the use of modern electronic digital computers to retrieve, compare, and build statistical mathematical models from the input. In the exploration process as part of his broader efforts to evaluate the potential of some prospective region, district, or ore body, the experienced geologist consciously or subconsciously compares and fits the observed geologic features to similar phenomena associated with known ore bodies with which he is acquainted. Thus an adequate conceptual "model" of the total geologic environment and type of ore body sought is an essential requirement for the successful exploration effort. Numerous such models of porphyry coppers already exist in the minds and notes of many experienced geologists today. These models are, of necessity, couched largely in qualitative terms and though they may be quite definite in the mind of the porphyry copper expert, the total concept of what constitutes a porphyry copper deposit and environment is difficult to convey in very precise terms. There probably is no such thing as a typical porphyry copper deposit. However, it is well understood that most of the deposits that have been studied have many geological characteristics in common. A logical question then might be: What characteristics are most common or how often do they occur in common, and what is their relationship to other common characteristics ?

Jan 1, 1970

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025

By Bernd Hagenah, Hans-Peter Vetsch, Eric Jones, Sean Cassady, Danielle Johnson, Petr Pospisil

There are a number of issues associated with freight trains in non-electrified tunnels that are fundamental during the planning and operation of a rail tunnel. During uphill operation, increased air temperatures at the air intake locations of diesel trains can reduce diesel motor efficiency (stalling/choking) and affect HVAC systems. Strong airflows can aggravate fire scenarios due to fanning or water-reactive cargo materials. This paper focuses on the impact of freight trains on tunnel safety concepts, strategies to overcome heat issues at locomotive air inlets and air quality in tunnels operating diesel trains.

Dec 1, 2022

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By B. T. Lusk, J. J. Silva Castro

Currently, there are several methodologies to assess ground vibrations from blasting. Of all available methodologies, one that is becoming more important is the waveform superposition or signature hole technique. This technique is based on a signature waveform assigned to each hole to build the complete waveform for the whole production blast, using the convolution between the time initiation sequence and the signature hole waveform. In the basic methodology of the signature hole technique, the waveform hole-to-hole is assumed to be the same. Several studies and field tests have proven that the waveform hole-to-hole, even in ideal rock mass conditions (rock mass with little or no joint system), changes. In addition to distance or confinement, other factors that could change the waveform hole-to-hole include different geologic paths from the source to the monitoring point and a different energy output of each hole, due to hole loading, explosive composition and/or contamination, priming, etc. These factors result in varying waveforms generated for each hole, making the waveform produced by each hole a somewhat random process. There is available in the literature some proposals to include variability in the waveform hole-to-hole, but the parameters involved are complex and difficult to estimate. In this paper, the variability in the signature waveform hole-to-hole in a blast event was recorded through a field test, and a proposal to include signature waveform variability to develop an equation based on the Fourier series is presented. This methodology is the basis for a future signature hole analysis using a Monte Carlo scheme, taking into account the variation of the amplitude and the frequency content of the waveform hole-to-hole in a production blast event.

Jan 1, 2012

By Dmitriy A. Malovichko

The general theory for the description of seismic sources is briefly discussed. The effect of excavations on seismic radiation is considered. Expressions for seismic source mechanisms in terms of the geometrical and mechanical parameters of source processes are provided for the following cases: fault slip and shear failure in a confined environment, dynamic stress fracturing around a tunnel, rock fall, landslide and sudden subsidence. A classification of seismic events in mines based on source mechanisms is introduced. The classification separates blast-, slip- and crush-type events. Various approaches of analysis of source mechanisms involving forward modelling and inversion are discussed. The following examples demonstrating the utility of source mechanisms in mining are presented: forensic analysis of damaging seismic events, assessment of the increase in the depth of failure for dynamic stress fracturing around tunnels and its duration, examination of the rockmass deformation regime, assessment of deformation around tunnels using crush-type events, identification and parameterisation of weak geological structures, stress inversion from slip-type events. Finally, the requirements for seismic data to ensure high quality source mechanism solutions are briefly reviewed and future challenges in the interpretation and utilisation of seismic source mechanisms in mines are speculated on.

Apr 26, 2022

By John O. Marsden

"This article is an attempt to capture a presentation given at the 2016 SME Mineral & Metallurgical Processing Division (MPD) Luncheon held on Feb. 24, 2016, in Phoenix, AZ. It was presented as a tongue-in-cheek, lighthearted view of several of the issues facing our industry, while identifying some of the challenges and opportunities available to new engineers entering the industry today.Disclaimer• What you are about to read includes personal preferences, biases and occasionally arbitrary opinions.• Some readers may have dissimilar opinions on the contents and/or the rank order of the lists.There are eight top ten lists offered in this article: (1) Industry realities (2) Things a metallurgical or mineral process engineering graduate should do (3) Books every metallurgist should have on their shelf (4) Things I wish I had known (5) Legends of metallurgy (posthumous, with highlights) (6) Things we’ve forgotten (7) Mineral processing innovations of the past 20 years and, finally, (8) The future? For some items, additional context or clarification is provided after the item, while for other items no further explanation is warranted and none is offered. Top 10 industry realities1. Metal price cycles.2. Bigger is better (except when it isn’t).3. Ore grades declining across the board of metals/commodities.4. Ores becoming more complex.5. Three-fold increase in capital costs between 2004 and 2015.6. Three-fold increase in operating costs between 2004 and 2015.7. Less capital availability/challenging financial markets.8. Environmental constraints increasing.9. Socio-political constraints increasing.10. The mine manager is always impossible to work with.As Table 1 shows, there was more than a three-fold increase in gold operating costs between 2004 and 2014. The increases for copper, iron ore and other commodities were similar."

Aug 1, 2016