Search Documents

By M. Scherbakov, W. Shi

Abrasion is an important mode of performance for any element of an engineered product that involves material contact for example, a conveyor belt cover. Abrasion resistance is considered to be one of the leading factors in belt cover design and improvement. Various types of abrasion testing are reviewed by and compared to actual belt applications. A new quantitative screening torsional abrasion test is developed by Goodyear to mimic a dynamic contact between belt cover and differently shaped stones of various weights dropped onto belt at any angle, velocity and height.

Jan 1, 2004

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Lawrence Adler

The design of an underground opening involves the coincidence of two highly complex and poorly specified components. First, the structural or mechanical characteristics of a geologic rock mass are not only extremely variable but are also very difficult to evaluate. Second, the general lay¬out of mine workings contains a large degree of indeterminancy as to the structure itself as a result of the indefiniteness of the mining process, and also because of the inherent redundancies associated with bulky and weighty structures. Even for the relatively simple problem of tunneling this complexity is well recognized to be "without question that to which the study of geo¬logy (for the Engineer) can most fitly and usefully be applied".1 It can, therefore, be appreciated that the comprehensive opening design problem involves a complicated assemblage of component structures made up of a sketchily defined, or sometimes even an undefined material and acted upon by largely unknown tectonic forces.

Jan 1, 1968

By R. A. Jankowsi, S. K. Ruggieri

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the "shearer-clearer," to push the dust close to the face. The techniques have been evaluated in field trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 6, 1985

For the past two years, Cliffs Natural Resources in Minnesota has tried an experiment: it has staffed a booth at the Iron Range Earth Fest. ?It was a little unusual for a mining company to participate in an event that centers around preserving the Earth?s resources,? said Julie Lucas, environmental manager at Hibbing Taconite Company. ?But Cliffs is a sustainable company and we want to take every opportunity to share information about our practices. We found the response to be overwhelmingly positive.? Cliffs? outreach effort is just one of the surprising ways mining companies across Minnesota are reaching out to stakeholders and finding success. The 85th annual SME Minnesota Section Meeting (73rd Annual University of Minnesota Mining Symposium), held April 17-18 in Duluth, MN, demonstrated the Minnesota mining community?s commitment to connection and collaboration, and how that approach is bringing success.

Jan 1, 2012

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By Scott G. Britton

Many times during the construction of a project, whether large or small, the engineer will become involved with management of the work and workforce. In some cases, mine management will turn over the direction and responsibility of doing the work to the engineer. Because of this, it is important to know some of the basic principles of human resource applications- among other management concerns. This chapter, therefore, looks at the fundamental principles of human resource management. Three broad discussions are presented to the reader. These are: (1) organization, communications, and responsibilities of management; (2) analysis of worker motivation; and (3) supervisory leadership. Each topic encompasses the current thinking for coal mining and mining management. Much of the information in this chapter comes from Practical Coal Mine Management, by this author and published by John Wiley & Sons, Inc., which discusses in depth many of the ideas presented here. Interested persons are directed to this text for more information on management skills.

Jan 1, 1983

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By Frank H. Blair

A study of paleogeography and paleo-environment, coupled with modern geochemical techniques and geologic inference, points to the presence of unconventional platinum group metal deposits in domestic and foreign ultrabasic terranes. During the laterisation of the tectonized and serpentinized mafic and ultramafic rock units, onshore winds provided abundant low temperature chloride to the laterite-saprolite profile. Here, an environment formed where gold, silver and platinum was dissolved, transported and redeposited. Changes in climatic conditions have helped preserve the redeposited metals in fossil laterites. The definition of "unconventional mineral resources" used here is taken from the Cameron Volume of Unconventional Mineral Deposits published by SME-AIME in 1983: "Unconventional mineral resources represent materials of possible economic importance that occur in geological or physical environments that have not been successfully exploited for the particular mineral." (van Rensburg, 1983). Chromite-rich rocks worldwide contain high platinum group metal concentrations. This feature is found in ophiolitic sequences, Alaskan-type ultrabasic complexes or statiform intrusions. Association of platinum group metals with chromite has received much attention. The reason for that associa¬tion, however, is not clear. Much has been written about how and where the platinum group metals occur. It is known that they are present in the spinel lattice, as solid solution elements in sulfides and as discrete platinum group minerals. This article outlines the reasons geologists should be looking at lateritic terranes to determine the feasibility of searching for undiscovered, low-grade platinum group metals amenable to openpit, bulk mining. Laterite-saprolite horizons could contain significant platinum group metals and location of anomalous values on the surface and in the weathered profile can lead to discovery.

Jan 1, 1993

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By Betty L. Gibbs

The ultimate objective of mine design is to determine the development and untilization of mining resources. Computer Aided Design (CAD) and automated mapping are becoming very popular in engineering and in mining. Any computer program which produces a design or model with the interaction of an engineer can be considered computer-aided design (CAD), but&apos; the term CAD is often associated with interactive graphic design and mapping capabilities. Graphics can be effectively used to describe and model two-or-three dimensional mine workings, orebodies, and geologic structures. Interactive computer graphics is applied to mine design with a combination of deposit modeling techniques and the use of AutoCAD for interactive graphics and mapping. The combined system can perform a large part of the calculations and drafting work for geologic and mining design. Using computer calculation and graphics techniques, comparisons of alternatives, can be made quickly.

Jan 1, 1989

By J. W. Sweeney

The .Florida land-pebble mining industry of central Florida was examined to identify trends in land use; conflicts in land use; and the effect of the conflicts on mineral resources. Many conflicts exist in the study area, such as conflicts with other users of land resources and land surface; conflicts with high revenue land users; conflicts for land surface in urban and suburban areas; and conflicting restrictions concerning utilization. Projections are made showing that lands in phosphate company ownership are expected to be made available to help meet the need for future urban expansion in the study area. Some phosphate resources have been lost due to land use conflicts, however, most of the resource loss has been small. Land use conflicts and phosphate mining are reconcilable and considerable progress toward their maximum and multiple use of land and mineral resources can be resolved through farsighted planning based on factual data.

Jan 1, 1972

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By B. J. Arnold, F. F. Aplan, S. Chander

There is a broad range of chemical reagents of potential use to the coal preparation industry: flotation frothers, flotation collectors (for coal, ash minerals or pyrite) and collector-assisting (conditioning) agents, flotation depressants (for coal, ash minerals or pyrite), pH regulating agents, acid mine drainage treatment chemicals, flocculants, filtration aids, dispersants, dust suppressants (wetting agents and car-top or pile binders), freeze conditioning agents, water treatment chemicals (corrosion and scale inhibitors) and suspension stabilizing reagents (dispersants, stabilizers, biocides). The application of each of these types is discussed with particular attention paid to those of greatest importance: flotation frothers and collectors, pH regulators and acid mine drainage treatment chemicals, flocculants and freeze conditioning agents.

Jan 1, 1986

By E. Azrag, A. MacDonald

A hydrogeologic investigation was conducted to predict inflow to underground mine workings and mining-induced hydrologic impacts for a proposed underground mine beneath a lake in northern Canada. Flow and shut-in tests were conducted to determine hydraulic conductivity values and to estimate the hydraulic head. A conceptual hydrogeologic model was developed and incorporated into a numerical ground-water flow model (utilizing MINEDW, a three-dimensional, finite-element code with special attributes designed for mine dewatering). The mining sequence was represented in detail(e.g., driving ramps and drifts, extracting panels, and backfilling mined areas). Due to limited field data, a quantitative assessment of uncertainty was implemented to estimate limits of possible inflows.

Jan 1, 2003

By Seokwon Jeon, Ho-Young Jeong

"Various numerical methods have been tried to estimate the cutting forces of a TBM disc cutter. In this study, SPH/FEM coupled method was newly employed to improve the traditional FEM analysis. The disc cutter and rock were modeled by Lagrange and SPH codes, respectively. The numerical cutting test was carried out for representative Korean rocks with different cutting conditions. The results show that the cutting forces obtained from numerical simulation had a good agreement with those from LCM tests, and that applying SPH method to rock cutting model has advantages and improvement compared to traditional FEM method. Erosion criterion and erosion limit were not required to simulate the rock fragmentation process, and the cutting forces from the numerical simulation was more stable and accurate. The results indicate that the numerical simulation can be successfully used to estimate cutting performance of a TBM. 1. INTRODUCTION Various numerical studies have been carried out to accurately simulate the limitations of linear cutting machine (LCM) tests. Numerical modelling methods have advantages comparing with full scale tests in terms of cost and time involved. Many numerical methods have been used to simulate rock cutting process by different cutting tools and the studies are summarized in Table 1.In 2D simulations listed in Table 1, because they do not take account of rolling force and horizontal rolling mechanism of a disc cutter, indenter was selected as cutting tool in their modelling. For these reason, 2D modelling is not suitable for rock cutting modelling using a disc cutter. In contrast, 3D numerical models can take account of the indentation process by thrust force and penetration processes controlled by rolling force."

Jan 1, 2016

By James Yancik

The Howe Coal Company located in Leflore County, Oklahoma is mining the Oklahoma Lower Hartshorne Coal bed which ranges in thickness from 38" to 42" and dips approximately 7 degrees to the Northeast. The Lower Hartshorne bed lies within the Hartshorne sandstone in Oklahoma but is as much as 60 feet above this sandstone formation in Arkansas. This coal bed extends throughout the Arkansas Oklahoma coal basin, which is about 50 miles wide and 180 miles long and progresses from a semi anthracite in Arkansas to a low-volatile coal in the eastern part of the Oklahoma to a high-volatile coal in the western area. The Howe Mine #1 in the eastern area is mining a low-volatile bituminous coal which has been used as metallurgical coal since the early 1900&apos;s as evidence of Bee-hive coke ovens still remain near the town Howe, a few miles northwest of the mine site. The Howe Mine is the first mine in the area to use modern mining equipment, however, numerous punch mines have been worked along the outcrop south of the mine site dating from 1900 with the last closing in 1965. The coal characteristics of the Lower Hartshorne rival the Pocahontas seam in chemistry and coking qualities. This paper will be concerned with the preparation of the coal for the Japanese steel market. The three man crew necessary to operate the plant are the operator, the helper, and the equipment operator needed to feed the raw coal hopper. An additional equipment operator is available on the day shift for coal loading and moving the clean coal to the storage pile as the area under the clean coal belt is only large enough for 1 shifts production. We are at present running the plant on a 2 shift per day basis.

Jan 1, 1969

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984