Search Documents

By W. Robert Power

Stone is considered by many to be the premium material for beauty and durability in all kinds of construction. Its use dates to the dawn of civilization and only buildings made of stone have survived from ancient times. The use of stone relative to other materials declined from the beginning of the present century reaching a low point in the third quarter, but there has been a resurgence in the use of stone in construction during the past decade, due probably, to new techniques for producing stone, a greater recognition of its beauty and durability, and greater affluence among consumers. The aesthetic appeal of stone is attested to by the many attempts to simulate it in synthetic materials. Today, natural stone is considered by many to be the ultimate in aesthetic appeal, durability, and ease of maintenance. Consumption of dimension stone has increased dramatically during the past decade. The US Bureau of Mines reported that the total value of US consumption in 1978 was $1 13 million and that total imports were valued at $65 million in 1979 (Anon., 1980). In 1989 consumption of domestic dimension stone was valued at $208.3 million and imports at $525 million. This dramatic increase occurred after demand had decreased at an average rate of 2.5% in the two decades prior to 1978 (Anon., 1980). More than half of the imports come from Italy, but production of dimension stone has increased worldwide spectacularly. Meaningful statistics on dimension stone are hard to acquire. The finished piece of stone is a highly value-added product, but stone may be sold as rough blocks, sawed slabs, or finished product. The same piece of stone may therefore be sold and reported three or more times. Furthermore, although the quantity of stone is most commonly reported in tons, stone cladding is more often sold by the surface area and at the same price for different thicknesses. By any measure, however, the production and consumption of dimension stone has increased dramatically during the past decade. A significant indication of the resurgence of stone was the introduction of two new trade publications during the 1980s. Stone World (Tradelink Publishing Co., Inc., Oradell, NJ), introduced in 1984 is published monthly and Dimensional Stone (Dimensional Stone Institute, Inc., Woodland Hills, CA), introduced in 1985 is published monthly. Both magazines provide useful information on new technology, market trends, producing areas and companies, and other information not previously available.

Jan 1, 1994

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

By S. G. Tough, H. J. Hignett

The Transport and Road Research Laboratory is carrying out tunneling trials at Chinnor, Oxfordshire, with a 5-m-diam, full-face tunneling machine. The work, which is for research purposes only, involves driving the tunneling machine through chalk with most of the physical characteristics of the machine and its power consumption closely monitered. At the Conference a film was shown about this work, illustrating both the tunnel construction and the research program.

Jan 1, 1974

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By P. D. Pattillo, J. B. Cheatham, Y. -H. Lin

The stability of a hemispherical cavity, intended to model a perforation opening in the vicinity of a borehole, is analyzed for the case of poroelastic-plastic material behavior. Two plasticity models of differing complexity are considered, with the emphasis in either model being the use of strain softening to calculate inelastic stiffness. Sample results illustrate the effect of steady fluid flow on the response, and possible collapse, of the near perforation region.

Jan 1, 1986

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

By I. Weir-Jones

[Currently the cost of carrying out 'in situ' geotechnical investigation programmes or installing and operating monitoring systems at construction or mining sites is rising var." rapidly. This is primarily because of our ever increasing labour rates. As a result of this problem efforts are no,, being made develop techniques for the economical; collection of large quantities of geotechnical data relating, to such problems as done stability evaluation, the behaviour of underground openings, or 'in situ' testing procedures. The efforts to reduce the labour content. are particularly apparent in those procedures which have traditionally been manpower intensive e.g. 'in situ' permeability testing where an entire drilling crew and their associated eguipment have been on standby while testis has been carried out; or data collection in underground construction operations where much tine is typically wasted obtaining or maintaining access to instrument sites. In an attempt to illustrate one specialist consulting company's approach to the problem of reducing investigation costs, this rarer examines four recent developments in the field of geotechnical investigation and monitoring which have come about during the last two Years as a result of cur research and development programme. Although these techniques and devices have been developed for specific projects, they all have broad applications in the geotechnical field and they are indicative of the direction in which this company feels developments will take place.]

Jan 1, 1975

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By R. C. Emmett

Gravity sedimentation is one of the most widely used unit operations in mineral processing and hydrometallurgy. Properly selected and operated sedimentation equipment can provide probably the most economical means of concentrating solids or clarifying solutions. Because of the variety of different approaches possible, including the use of modern flocculants, it is easy to overlook the optimum approach in selecting equipment. The different types of sedimentation systems that can be used in the minerals field and the sizing methods that are currently employed will be discussed here. Sedimentation applications usually fall into two areas, clarification or thickening. While the two operations are basically similar, the difference in emphasis (a well-clarified overflow as opposed to a highly concentrated underflow) results in significant differences in testing, equipment design, and operation. Clarifiers may be merely simple settling vessels with no special features, other than ample volume to provide the detention time needed for suspended solids to settle out of the feed slurry. Or, they can be designed to employ elaborate solids-contact techniques utilizing coagulants or flocculants to achieve more rapid clarification through the growth of particle agglomerates. Thickeners also are available in a wide variety of designs, with the main differences concentrated in the design of the raking mechanism. Thickeners operating in series (continuous countercurrent decantation or CCD) are used to recover valuable solution or purify the insoluble solids. Tray thickeners are used for recovering fine particulate solids such as alumina seed, but in other applications have been supplanted largely by unit thickeners or inclined plate units. Thickeners and clarifiers sometimes are used for storage of either solids or overflow liquor, or employed as precipitating reactors, such as in desilication applications. The use of flocculants and coagulants is much more common in modern processing plants, primarily due to the reduction in capital costs rendered possible through the use of these reagents. The terms flocculant and coagulant are often used interchangeably; generally, it is understood that flocculants refer to organic, high molecular weight synthetic or natural polymers which are useful in flocculating most suspended solids, but generally are ineffective on colloidal suspensions. Coagulants refer to chemicals such as those commonly used in water treatment, alum, ferric salts, lime, etc., which are usually far more effective on colloidal solids but cannot achieve the degree of agglomeration that is possible with the polymers. In some cases, both coagulants and flocculants are used in order to achieve optimum results.

Jan 1, 1986

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By T. J. Toy

The topography reconstructed following land disturbance is the foundation for all other reclamation practices. As the manufactured drainage basins, hillslopes, and stream channels approach a steady-state condition, the amount of adjustment of these landforms by geomorphic processes following reclamation decreases. As the adjustment required to establish a steady-state condition decreases, the prospect of reclamation success increases while the prospect of site maintenance decreases. Careful topographic reconstruction is a good investment.

Jan 1, 2002

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By Marcos C. Filgueiras, Thomas A. Post, Michael A. Giralico, Daniel M. Adams

The leaching of copper, gold, and nickel in tanks requires mixing. Minerals require oxygen, acid and/or base [NH3] to assist in the leaching process. Two basic types of tanks are used for this operation. They are either vertical tanks or closed horizontal tanks called autoclaves. This paper discusses mineral leaching, it's mixing requirements, and autoclaves.

Jan 1, 1999

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By Lynn B. Hales, Randy A. Ynchausti

Expert supervisory control strategies have been used for many years to improve operating revenues in comminution circuits. Typical improvements in capacity range from four to eight percent. Several case studies of results will be presented as well as a general discussion of the technologies used to achieve the improvements. Crushing. SAG milling and ball milling circuits will be discussed.

Jan 1, 1997