Search Documents

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By S. Tandanand

The Bureau of Mines, U.S. Department of the Interior, assessed the geological effects on the ratio of maximum subsidence and extraction thickness, hown as the subsidence factor, to develop a simple method for predicting the maximum subsidence. The study is restricted to the Northern Appalachian Coal basin where data were collected from 13 coal mines. A model previously developed to relate the subsidence factor with the lithology and with the width and depth of working panels was used in the assessment. The result shows the possibility of determining maximum subsidence without resorting to a rigorous method.

Jan 1, 1982

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By Luther J. Russell

Mineral development in South Dakota is aggressively encouraged by both state statute and county ordinances. Yet, an increasingly conservative philosophy is taking hold, resulting in expanded regulatory controls and concomitant increases in direct and indirect costs to permit and operate a mining operation. This paper examines the hidden costs associated with protracted permitting timeframes, land buy-outs, attorney's fees, etc., associated with the increasing emphasis for stiff controls on mineral development in South Dakota.

Jan 1, 1998

By T. Janke

When Homestake Mining Company's Mclaughlin Gold Project was being evaluated for development, it was apparent that recovery of gold from mined ore would be difficult and relatively expensive. The ore was refractory, averaging less than 50% recovery in conventional direct cyanidation milling tests. Extensive testing narrowed the processing choices to either autoclave or roaster oxidation before cyanidation. Roasting was ruled out due to higher capital and operating costs --the Mclaughlin mill would be the first large-scale application of autoclave oxidation of a refractory gold ore.

Jan 1, 1989

By F. Gray

Diamond tool fabricators expect strong growth in most applications for 1995 and 1996. Overall growth projects range from 8% to 10%. Diamond grinding is forecast to grow between 5% and 8%, while cubic boron nitride grinding should grow between 10% and 12%. A strong automotive industry is a major factor in this projected growth, as is continuing demand for other durables

Jan 1, 1995

By James D. Bennett

Relationships among mine and injured miner characteristics and HSAC's degrees of injury are examined for 91,404 injuries in under- ground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner's age, whether the miner was using powered equipment, the year which the injury occurred, and the location in the mine where the injury happened. Injury severity is not related to the injured miner's total mining experience, job experience, and experience in the mine in which the injury occurred.

Jan 1, 1984

By Larry Snyder, Levent Ozdemir, Charles Fishman, Fun-Den Wang

Tunnel Boring Machine Instrumentation A 9.17 m. diameter tunnel boring machine presently in operation in Chicago, Illinois, has been instrumented to continuously monitor and record machine thrust, torque and penetration rate during boring. A micro-processor-based data logger capable of monitoring up to 60 channels of data digitizes and converts into appropriate engineering units the signals from various transducers mounted on the machine. The output from the data logger is sent to a teleprinter, providing a permanent record of measured data. The program control enables the data logger to scan all data channels at desired time intervals. Data obtained to date have been analyzed to determine the interrelationships of the parameters measured. Penetration rate was found to increase linearly with machine thrust with a unit increase in thrust causing more than a unit increase in penetration rate. For low thrust levels corresponding to the initial stages of a boring cycle, the penetration rate was observed to behave erratically until the thrust pressure was sufficiently high for the cutters to establish full contact with the tunnel face. Torque showed a curvilinear increase with machine thrust, reaching the design rating at about 70% of maximum available thrust. No-load torque was approximately 20% of the machine's rated torque capacity. Overall, the trends observed in measured machine parameters correlated closely with those predicted from experimental and theoretical boreability studies. In summary, the instrumentation system has mett two basic goals. First, it provided extensive and accurate boring data and secondly, it has proven that an automatic data acquisition system can be installed on a TBM and can function under adverse environment.

Jan 1, 1979

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By Robert Giglio

Looking back over the last 150 years or so, it is not hard to see that electricity has been a primary force in shaping human development. It has been a basic ingredient in our industrial revolutions that simultaneously improved the productivity, working and living conditions within our farms, factories, hospitals, offices and homes. Today, it has become an essential part of our daily life and our future. Amazingly, we keep finding new ways to use electricity to make our lives more safe, comfortable and productive. It is a great success story of human ingenuity, achievement and development. Demand for electricity The convenience and value of electricity has not gone unnoticed by consumers. According to the U.S. Department of Energy (DOE) (Energy Information Administration, 2009), electricity is the fastest growing form of energy in the world and during the next 20 years the world will likely consume twice as much of it as it does today. In 2008, almost 20,000 terawatt hours of electricity globally were consumed (Energy Information Administration, 2009). That is enough electricity to light up more than two million baseball stadiums or power more than 11 billion computers continuously for an entire year. The United States has the dubious distinction of be-ing the largest consumer of electricity in the world with enough power to provide each American with more than 3 kW of electricity ? that is about twice the power currently available to Europeans, eight times the power available to the Chinese and more than 25 times the power available to the citizens of India (American Coal Foundation, 2009).

Jan 1, 2009

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By James Boyd

JAMES BOYD 29.1-STAFF-AND-LINE ORGANIZATION Industrial organizations are established primarily to coordinate the activities of many individuals working toward a specific goal. In mining, the goals can vary widely, and the skills necessary to reach them likewise will vary from operation to operation. It is essential to keep in mind the principal point that an organization embodies the necessary skills which supplement each other and achieve a given objective. Those who direct such an organization are grouped together as "management" and accept the responsibilities for the regulation, administration, supervision and guidance of the enterprise. Those who comprise the "administration" and have supervisory authority are referred to as the "executives." In the early days of mining it was common for one executive to exercise virtually complete control over the entire organization, and direct its operation from a central office. However, the science of management has advanced significantly since then. Mining organization administration now allocates increased authority and flexibility to those in direct-line responsibility, and organizes competent people in specialized fields to provide supervisors with guidance where it is needed in day-to-day operations. Few mining companies today are confined to one operation. Therefore, highly developed skills can be provided in the staff which assists management. This is known as staff-and-line organization, illustrated, in general, in Fig. 29-1. Each operation requires diverse skills for the carrying out of specific functions. The acquisition and training of those with such skills is an important operation in assembling organizations. An organization normally is modified to accommodate individuals rather than being a "hard and fast" mold into which people are fitted. The modern manager is inclined to organize to minimize central direction, with delegation to line executives, providing staff whose day-to-day operations, in cooperation with line executives, coordinate a continuing drive toward the organization's objectives. The staff officers, therefore, tend to become what could be described as parts of the president's brain, dealing with specific areas requiring certain skills. They do not necessarily direct operations, but watch them to be sure that the skills which they have themselves developed can be transmitted to line operations by persuasion rather than by direct authority. The elements of management requiring staff assignments are: 1. Planning, which, at staff level, is only a coordinating activity. Planning is done at all levels in the organization. 2. Engineering. 3. Finance. 4. Control. 5. Personnel and industrial relations, which set personnel policies, including salary plans and the means of handling relations with the unions. 6. Research, which, in a modern organization, is essential to progress and needs to be overseen at the top. 7. Legal staff to see that all operations of the company are provided with sound legal advice, and that the company's policies stay within the law.

Jan 1, 1973

By M. C. Fuerstenau, J. J. Fitzgerald

Aluminum silicate hydrosol synthesis and characterization are discussed. Plausible polymeric aluminosilicate species are presented together with their effect on electrokinetics of selected minerals and flotation response of various ores. The addition of aluminosilicate hydrosol to porphyry and oxide copper ores and to a tungsten ore resulted in enhanced flotation recoveries ranging from about 1.5 to 5 percent. A significant portion of the nation's mineral resources are presently lost in the form of particles with very fine grain size. In the case of copper, for example, approximately 225 million tons of ore are concentrated by flotation per year in the United States. Total losses from porphyry ores are generally 15 to 20 percent with half of these losses being finely-divided copper sulfide minerals which do not respond to flotation. The additional 5 to 10 percent loss is the result of copper oxide minerals which are not floated. The losses of copper sulfide minerals are thought to be due in part to the lack of appropriate dispersion of the finely-divided solids less than 20 microns in size. To effect dispersion in flotation systems, sodium silicate is commonly added. Enhanced dispersion effectiveness is achieved when polyvalent metal salts are combined with sodium silicate. Since originally described by Patek (1), numerous workers have explored the utility of metal silicates. Makrousov (2), Belash et al. (3), and Eigeles (1950) (4) showed the applicability of these reagents to calcite/apatite and fluorite/calcite ores. Mercade (5, 6) reported depression of calcite in the presence of 3.33/1 mole ratio Al/Si hydrosols prepared from Type N sodium silicate (Si02/Na20 ratio 3.22/1) and 1% A12(SO4) 3•18H20 solutions. He importantly observed that the colloidal precipitates did not play a significant role in dispersion and depression but that the soluble species were responsible for this action. Patented work by this author described metal silicates used to depress calcite in scheelite flotation using 1% metal salt (FeSO4•7H2O, CoSO4•7H2O, etc.) and 5% Type N sodium silicate solutions to produce hydrosols with Si/Fe or Si/Co ratios of 8.79/1. Aluminum (III) ion systems were less effective as depressants than the iron and cobalt systems. Yang (8, 9) has studied metal silicate sols for use in the flotation of lithium and ultra-fine hematite ores. Using 10/1 Si/Fe mole ratio hydrosols prepared from 2% ferric nitrate, Fe(NO3)3.9H20, and 5% Type N sodium silicate solutions, solutions, he showed that the hydrosols either modify the slime particle surfaces or are adsorbed on the slime particles preventing anionic collector adsorption. In a subsequent patent, Yang also reported the use of these hydrosols as dispersants for beneficiation of lithium ores. Recent studies of aluminum silicate hydrosols in the flotation of chalcocite, chalcopyrite and scheelite have been reported using Si/Al dispersants prepared from 5% Type N sodium silicate and 0.1 M aluminum chloride (A1C13.6H20) solutions. Dispersant properties were shown to be dependent upon the method of synthesis, supernatant pH, and the hydrosol Si/Al mole ratio. Polymeric soluble species in these hydrosolsupernatants have been proposed as the active dispersant species. Aluminosilicate hydrosols are synthesized by the general reaction scheme presented in Figure 1. Commercial sodium silicates are available with ratios of SiO2 to Na20 of 1.60-3.25. The sample which is most frequently employed is Type N whose ratio of Si02/Na20 is 3.22/1.00. Gel filtration chromatography and NMR studies have shown that these sodium silicates contain numerous species of molecular weight from 325-2,000 gm/mole. Monomeric, oligomeric and higher molecular weight linear polymeric arrangements of these structures are found in these solutions.

Jan 1, 1989

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986