Search Documents

Acid mine drainage is still a common problem in the northern Appalachian high sulfur coal region despite mining and reclamation practices applied to control it. Mining companies must treat water with alkali to raise pH and precipitate metals in order to discharge the water into receiving streams. Common chemicals used to treat drainage are limestone, hydrated lime, soda ash briquettes, caustic soda, and ammonia. Each chemical has advantages or disadvantages under specific conditions. A simple spreadsheet program was developed to evaluate costs of treating acid mine drainage across several specified water quality parameters and time horizons. Caustic soda and soda ash were shown to be cost effective for treating low flows and low acidity over short time periods. However, as quantity of water increased, quality decreased, and time horizon increased, the ammonia and hydrated lime systems were found to be much cheaper than caustic soda.

Jan 1, 1991

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By A. Bruynesteyn

I would like to talk to you today about microbiological leaching or, the solubilization of metal values due to the action of Thiobacillus ferrooxidans. Bacterial attack of sulfide minerals has been going on for centuries but only recently was it discovered that the acid and iron often found in coal mine drainage is produced by bacterial action on the iron sulfides in the coals. Not until 1950 was it proven that bacteria were playing a role in the dump leaching of sulfide ores. B. C. Research became involved in microbiological leaching in 1955 while examining mine drainage from the copper-zinc mine at Britannia Beach, north of Vancouver. Since 1955, B.C. Research has maintained a continuous re¬search program on microbiological leaching which, due to its applied nature, was put under industrial sponsorship in 1962. Most of the information pro¬vided in my talk today has been gathered under this sponsored research program and I would like to express our appreciation to the many sponsors who have made our work possible.

Jan 1, 1970

By J. M. Barker, V. T. McLemore

Most discussions of sustainable development (SD) in mining relate to metal mines in rural areas. Industrial minerals (IM) are closer to urban areas primarily owing to a high transport-cost component of delivered cost. This visibility to large populations overshadows IMs relatively small operation size and generally lower waste volume and toxicity. The IM industry needs to rethink its way of doing business to fit into the SD paradigm. Society and business in general will also undergo significant change to enable industrial SD along the lines of triple-bottom-line accounting with government pushing everyone. The benefit to IM mining from embracing SD is a renewal in their social license to operate and a rebirth of mining as a positively-viewed force in society. This positive view would lead to lower acquisition costs because society would not fight so hard to eliminate nearby mining. This would ease the current exploration woes of the IM industry by opening up new deposits for exploration and more readily allowing placement of mines nearer to markets. The earlier in the exploration process SD is initiated, the better.

Jan 1, 2004

Application of microprocessors, programmable logic devices, and other computer-oriented hardware and software on-board large surface mining equipment to optimize availability and productivity, stretch machine life, and protect against catastrophic breakdown has been a goal of heavy-equipment manufacturers for several years. Progress in this direction has not been as rapid as many manufacturers anticipated in the mid-1980s, and, on the other side of the coin, mining industry and machine operator acceptance of such products has not always been enthusiastic. However, the trend toward such development seems undeniable. Large surface mining equipment in the future will doubtless carry more, and not fewer, applications of computers and computer-related products. The intensity of development interest and degree of progress in commercializing such on-board computer and computer-related products on surface mining equipment varies considerably among the manufacturers. Summarized here are the on-board computer-oriented products of three heavy-equipment suppliers-P&H Harnishfeger, Marathon LeTourneau, and Haulpak not a comprehensive survey, but, perhaps indicative of the direction such development is taking.

Jan 1, 1990

By E. T. Balazs

Share of developing countries in world bauxite resources mining and processing. Technical assistance of the United Nations Industrial Development Organization to the developing world in the field of bauxite evaluation and processing. Review of selected projects of bauxite research and development aimed at creating indigenous capabilities in developing countries: "Assistance to the bauxite aluminium industry of the People's Republic of China". Project activities. UN inputs. Achievements. Follow-up. "Upgrading the scientific and technological capabilities of the Jamaica Bauxite Institute". Project activities. UN inputs. Achievements. Expected follow-up. Assistance to the establishment of an "Aluminium research, development and design centre" in India. Project activities. UN inputs. Achievements. Follow-up. "Establishment of an aluminium institute for research and development in Titograd, Yugoslavia". Project activities. UN inputs. Achievements expected. Second UNIDO group training on bauxite evaluation and processing to alumina October - November 1983 in Budapest, Hungary. Programme and coverage. Show of movie picture on organization and execution (15 minutes). Significance of UNIDO's assistance to the developing world in bauxite research and development. References.

Jan 1, 1984

By Dennis C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required about 3 Mm2 (32.3 million sq ft) of fill over an area of about 600,000 m2 (6.5 million sq ft) in irregular terrain with relief of up to 40 m (130 ft). Earthwork construction was completed in about six months using mine waste, placed in 4 to 6 m (13 to 20 ft) lifts with mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10 m (33 ft). This was done to develop a mat for additional resistance to possible differential settlements due to the modest density of the fill and dynamic (earthquake) conditions. A single 2-mm (80-mil) high-density polyethylene (HDPE) liner was used below the leach pads. This was protected from the loading and unloading equipment by bedding and cover systems. It consisted of screened sand, gravel and silt as the bedding and cover layers and a heel of screened gravel and primary crushed low-grade ore.

Jan 1, 1995

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g., tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions was studied to improve estimates of dripping rates, drop sizes and the chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation was analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2002

By W. F. Hahnert, T. L. Ward, K. E. Stoll, P. A. S. Ralston

Fuzzy logic is well suited to the control of non-linear, time-varying, and/or any system for which it is difficult to obtain an exact mathematical model. To design a good fuzzy controller, a thorough understanding of the desired process behavior is required. Many papers have suggested that fuzzy controllers are robust. If they are, it is reasonable to explore whether or not they respond better than conventional controllers to errors in the feedback signal due to imperfect measurement or sensor degradation. It may be the case that simpler or less expensive sensors could be used in some processes. The research presented here relies on an integrated array of computer programs that model and simulate (1) the process to be controlled, (2) common feedback instrumentation, and (3) both fuzzy logic controllers (FLC's) and conventional controllers. Various types of feedback sensor imperfections are imposed upon the system, and the performance of the two controllers is compared. Each controller is tuned to its optimal performance in response to a setpoint change using perfect feedback measurement.

Jan 1, 1993

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By J. A. Dlas Lima

Alunorte is a metallurgical-grade alumina refinery located in northern Brazil. This plant which was designed to produce 1.1 million mtpy of calcined alumina, started operation in July 1995. A process information system was installed before refinery start-up. It has been a main factor in process improvements, which resulted in an increase in production from 1.1 to 1.5 million mtpy. This system has been particularly useful for analyzing data and allowing retrieval of data by process engineers. This paper describes how a quality monitoring system to evaluate all aspects and stages of production, as well as alumina silo level and blending percentage, was developed. This system was designed to give support to ISO 9002 certification, which happened in December 1998. The quality monitoring system was developed using Microsoft Excel 7.0 and makes extensive use of VBA macro. The primary users of the system are shift foremen, managers and engineers, who use it to track the process and avoid variations in alumina quality.

Jan 1, 2000

By A. E. Isaacson

The Bureau of Mines is studying the effect of supercritical water, at 4000 C and 3,500 psi and subcritical water at lower temperatures and pressures. on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By C. Heath

US coal consumption reached new heights in 1985, but production was constrained by excess consumer inventories. Domestic consumption of coal reached a record 742 Mt (818 million st) during the year. This is a 3.4% gain over the previous consumption high 718 Mt (791 million st) in 1984. An additional 84 Mt (92.7 million st) of US coal were shipped abroad in 1985, up 13.7% from exports a year earlier. Coal production in 1985 totaled 804 Mt (886 million st), 1.1% below the record 813 Mt (896 million st) produced in 1984. The slight decline in coal output is attributed primarily to a 13% drawdown of large consumer stockpiles built up in 1984 in anticipation of a miners strike that never occurred. Coal demand, and hence production, were also restrained by slower economic growth in 1985 and additional gains in nuclear generation of electricity. Domestic market requirements for coal in 1985 were mixed. Electric utility consumption rose 4.4%; coke plants consumed 6.7% less coal; coal requirements in the other industrial sector expanded by 2.1% and consumption in the residential and commercial sector fell 14.8%. The 2.2% increase in electric power generation in 1985 resulted in a 4.4% rise in utility coal consumption, totaling 630 Mt (694 million st) for the year. Twenty-nine of 45 states where coal-fired electric power plants were operating shared in the 26.7 Mt (29.5 million st) increase in 1985. Coal receipts at utilities fell by 16 Mt (18 million st) as these facilities worked off 21 Mt (23.4 million st) from stockpiles during the year. Electricity generation at coal-fired power plants similarly climbed 4.4% to 1.4 trillion kWh in 1985. This gave coal a 56.8% share of electricity generated from all energy sources compared with 55.5% in 1984. The average price of coal delivered to these facilities remained essentially unchanged during the year. It declined on 1.5% from $38.26/t ($34.71 per st) during the fourth quarter of 1984 to $37.70/t ($34.20 per st) in the fourth quarter of 1985. Coal consumption at coke plants continue to reflect a depressed steel industry. After rebounding 18.9% in 1984 for the first time in five years, coal consumption at coke plants again declined 6.7% to 37 Mt (41.1 million st) in 1985. Coke consumption 26.5 Mt (29.3 million st) exceeded production, 26 Mt (28.7 million st), in 1985. This resulted in a 1-Mt (1.2-million st) decline in coke stocks at producer and distributor levels during the year. The average price of coal delivered to coke plants decreased 7.6% from $64.30/t ($58.34 per st) during the final quarter of 1984 to $59.42/t (53.91 per st) in the last quarter of 1985. Coal consumption in other industries, including all manufacturing and industrial consumers except coke plants, totaled 68.3 Mt (75.3 million st) in 1985. This was the highest level attained in more than a decade. But the lower percentage rise last year (2.1% compared to 11.8% in 1984) reflected slower growth in the nation's economy in 1985. The average price of coal delivered to industrial firms declined 4.5% from $42.32/t ($38.39 per st) in the fourth quarter of 1984 to $40.39/t ($36.65 per st) in the last quarter of 1985. Coal-producing states in Appalachia mined 9.8 Mt (10.8 million st) tons less in 1985 than in 1984 for a 2.4% loss. The largest contributors to the region's production decrease to 393 Mt (433 million st) were Pennsylvania, down 14.7% to 60 Mt (66 million st); Ohio, down 8.3% to 32.6 Mt (36 million st); and West Virginia, down 2.9% to 115 Mt (127 million st). Conversely, eastern Kentucky production was up 4.8% to 111 Mt (122.8 million st) in 1985, while production in Tennessee climbed 9.7% to 40 Mt (44 million st). No coal was mined in Georgia last year. Coal production in the interior region in 1985 declined 3.9% to 173 Mt (190.4 million st). Substantial production losses occurred in Indiana, down 8% to 31 Mt (34.5 million st); and in western Kentucky, down 7.9% to 36 Mt (40 million st). Coal production in Texas rose 5.7% to 39 Mt (43.5 million st) in 1985. Louisiana began mining lignite 140 kt (151,000 st) during the year. Production in the western region increased 3.4% to 238 Mt (262.5 million st) in 1985. Wyoming, up 5.3% to 125 Mt (140 million st); and North Dakota, up 16.5% to 23.5 Mt (26 million st) contributing the largest amounts. Production gains were also shown in Washington, Utah and, notably, in Alaska where coal output climbed 72.9% to 1.3 Mt (1.5 million st) in 1985. Most of the additional coal produced in Alaska last year was shipped abroad. Coal stocks held by consumers totaled 154 Mt (170 million st) at the end of the year. This was 27 Mt (30 million st), or 13.7% below the inventory level at the end of 1984. Stocks held by producers and distributors declined by 868 kt (957,000 st), or 2.8% in 1985 to 30 Mt (33 million st). A drawdown in stockpiles occurred in each consumer sector during 1985. Stocks held by electric utilities totaled 142 Mt (156 million st) at the year's end, 13% lower than stock levels at the end of 1984.

Jan 5, 1986

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

An understanding of forces responsible for the stability of dispersions of colloidal particles when interacting with each other in aqueous solutions is of great interest academically and industrially. When water-soluble polymers are adsorbed onto colloidal particles, various effects on the stability of their suspensions can be expected ranging from steric stabilization to bridging flocculation. The possibility of detailed characterization of such systems using direct measurements of interaction forces between particles can help in further improvement of existing technologies of solid-liquid separation. An atomic force microscope (AFM) colloidal probe was used to measure the interaction forces between a silica sphere and a silica substrate in the presence of water-soluble polymers. Poly(ethlene oxide) (PEO) with three different molecular weights (7,000, 43,000, and 63,000), each with a very narrow molecular weight distribution, were used in this study. The interaction forces measured with the AFM over an extended time scale are discussed in terms of the adsorption kinetics measured through in-situ FTIR/IRS measurements.

Jan 1, 2003

By C. B. Rash, W. W. Fowler, Gill Montgomery

INTRODUCTION Fluorspar is the common term used for the mineral fluorite, which is naturally occurring calcium fluoride (CaF2). It is the principal source of fluorine, the most reactive of the chemical elements, from which a great variety of unique and strategically important chemicals are produced. Commercial deposits of fluorspar are widespread throughout the world, and its availability is essential to the industrial progress of all nations. GEOLOGY AND MINERALOGY In its pure form fluorspar, CaF2, contains 51.1% calcium and 48.9% fluorine, and has a sp gr of 3.18 and a hardness of 4. It is commonly a glassy mineral. colorless, white, or grayish. but may also be various shades of purple, pink, blue, green, yellow, or tan. It belongs to the cubic system mineralogically, and commonly crystallizes into cubic shapes in vugs and cavities, although most of it is massive, with interlocking crystals. Minable fluorspar deposits, in descending order of importance, occur as bedded limestone replacement deposits along fault zones; fissure-filling vein deposits; breccia filling in limestones, dolomites,

Jan 1, 1985

By F. B. Henderson, D. Bird, P. L. Hauff, E. C. Prosh

A National Aeronautics and Space Administration (NASA)-funded project (NASA Grant #NAG13-02026) is underway to determine the ability of hyperspectral remote sensing to map mineralogy that affects water quality within a watershed and to identify the relative contributions of natural and anthropogenic sources to that drainage. Natural sources, particularly areas of pyritic hydrothermal alteration, have been found by the Colorado Geological Survey to be a significant source, sometimes the only source, for acidity and/or metals in a number of areas of Colorado (Neubert, 2000). This situation undoubtedly occurs in many places in the Western United States and elsewhere where metallic mineralization occurs. Anthropogenic sources arise from mining and other human activities that increase the exposure of acid-generating materials to weathering processes, thereby increasing acidity and metal loading to drainages where that activity is occurring or has occurred. This project is attempting to determine if these sources can be differentiated through mineralogical analysis, in conjunction with surface water chemistry that controls the precipitated minerals, of the impacted drainages by remote sensing techniques.

Jan 1, 2003