Search Documents

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results of an investigation of the application of thermal fragmentation in Australian hard-rock, underground, narrow-vein mining. Two geologically similar samples from an underground, narrow-vein, hard-rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method.

By F. Dingwu

The demand of manufacturing high-purity magnetite concentrate leads to the advent of various magnetic separators. A novel magnetic drum separator has been developed with an optimal permanent magnet system and a complex-forces field is adopted, involving magnetic force, gravitation, fluid resistance, friction, inertial centrifugal force, etc. Proper ultrasonic probes are inserted into the bottom tank to break up the magnetic floes. The performance of magnetite in the complex-forces field is described and the optimal operation conditions are suggested.

Jan 1, 1995

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

Historian and storyteller, Duane Smith, will be the keynote speaker at the National Mining Hall of Fame's 10th anniversary induction banquet on Saturday, Sept. 6,1997 in the Museum Convention Center at Leadville, CO.Smith is a professor of history and southwest studies at Fort Lewis College in Durango, CO. He is also an award-winning author of 28 books about the West and mining. Hall of Fame Board Chairman Richard Moolick said the induction banquet event will mark the National Mining Hall of Fame and Museum's 10th anniversary in its Leadville facility, a century-old Victorian schoolhouse. Karl Elers, chairman of Battle Mountain Gold in Houston, TX, will be the master of ceremonies. He is a member of the National Mining Hall of Fame and Museum's board of directors. The six inductees into the National Mining Hall of Fame will be enshrined by Thomas Falkie, president of Berwind Natural Resources of Philadelphia, PA. He is also chairman of the Mining Hall's board of governors. The six inductees will join 132 mining greats who were previously honored. The black-tie (optional) banquet will be highlighted this year by guests who prefer to don 1890s dress for the occasion in the old silver-mining boomtown. A cocktail reception and open house will precede the banquet, with tours of the district and special events to follow on Sun- day, Sept. 7.

Jan 1, 1997

By C. R. Everly

"The purpose of this paper is to review the most effective methods of reducing chloride transfer and chloride removal in the solution extraction and electrowinning (SX/EW) process. Elevated chlorides in electrolyte have various negative effects including a reduction in current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Historical controls that Sierrita has used to control chloride transfer, in order of effectiveness, have been chloride gasification at the EW that is directly correlated to amperage and chloride concentration in electrolyte, wash stage bleed and efficiency, width and velocity of aqueous bands, and electrolyte bleeds. Maintaining high bleed rates and high amperage settings has been a challenge with decreasing pregnant leach solution (PLS) grades, so keeping chlorides out of the electrolyte has become imperative. The effectiveness of reducing aqueous entrainment, optimizing wash stage efficiencies, and improving organic quality to reduce the transfer of chlorides to the electrolyte are illustrated in this study. INTRODUCTION The transfer of impurities from PLS feed streams to electrolyte in the Copper Solution Extraction process is a very common problem and is the reason that the wash stage exists in most SX operations. The main impurities affecting the SX process are iron, chloride, nitrate, and manganese. Elevated chlorides in the electrolyte have various negative effects including reduced current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, increased cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Freeport-McMoRan Sierrita Hydromet is unique in that a high-chloride byproduct stream from the molybdenum process is pumped into the SX raffinate solution pond. This byproduct steam accounts for the majority of chloride introduced to the circuit, and over the years has built up to a point where 4000ppm chloride is consistently in the PLS feed to the SX. Concentrations of chloride over 70 ppm in electrolyte will result in downgraded cathode, so it is important to limit chloride carryover from SX as much as possible. Historically, Sierrita has been able to manage chloride levels with reactive techniques including increasing electrolyte bleeds and rectifier amps. Decreasing copper in PLS has made high amps harder to maintain, and increasing bleed rates have a direct impact on production goals."

Jan 1, 2015

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971

By K. Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1993

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By R. C. Timberlake

An understanding of the Florida Phosphate Industry, the mining practices and extraction processes and the historical development of the Industry, is essential to any consideration of reclamation. In the earliest days of the Industry, phosphate rock was produced by screening the phosphate pebble from the matrix. The waste, which consisted of overburden, clay, sand and fine phosphate, and was called "debris", was disposed of onto, either the adjacent surface area, or into mined-out pits. Since the Central Florida area was sparsely settled in those early days, there was no complaint from residents about contamination of streams or the resulting spoil piles - environmental concerns were non-existent. The development of the flotation process in the 1930's and the implementation of the flotation process in the early 1940's was a significant technological breakthrough in the Industry. This technique made possible the extraction of fine phosphate particles, and doubled the recovery of phosphate values from the matrix. However, the implementation of the flotation process produced a new waste disposal problem.

Jan 1, 1978

By M. S. Riyaz Ulla

The Hutti Greenstone belt, located in the northern side of Dharwar Craton, India, contains several promising gold fields. It is predominantly composed of meta-volcanics with minor intercalations of meta-sedimentaries. Alkali-SiO2 and Zr-P2O5 diagrams, immobile element trends, and an iron-rich trend on the AFM diagram indicate that the volcanic suite is low-potassium tholeiitic basalt. The lower Mg number, MgO-TiO2, MgO-Ni, and Ni-Zr plots reveal that the basalt was derived from a fractionated, highly evolved magma generated by 10-20% melting of the mantle at 1100°C and 5 kb pressure. The chemical variations suggest that the Hutti metabasalt represents volcanic arc rocks generated at a converging plate margin.

Jan 1, 1993

By G. Deschenes, M. Fulton

The New Britannia Mine processes a qumtz-carbonate gold ore containing 4.63 git Au at a rate of 2,200 tpd. The ore contains approximately 3 .0% arsenopyrite, 2. 7% pyrite and the rest is gangue minerals. Eight to ten percent of the gold is refractory to leaching. Two years ago, New Britannia Mine experienced cyanidation problems. Gold extraction was not stable and occasionally decreased significantly. Preliminary test work, at laboratory scale and in the plant, indicated that lead nitrate addition was beneficial. A laboratory study was initiated to evaluate the level of control of the parmneters (grinding size, dissolved oxygen, pH, free cyanide and lead nitrate) to optimize the efficiency of the process. It was found that lead nitrate addition is required to alleviate the effect of metallic sulphides. This addition causes a significant increase in the gold leaching kinetics and a reduction in the cyanide consumption. The optimum system appeared to be: leaching for 24-30 hours at pH 11.8, 50 git lead nitrate, 250 ppm NaCN and 8 ppm 02. The gold extraction was 89.8% with grinding at 89%-74Fm (leached tail at 0.48 git). Cyanide and lime consumption are 0.40 kglt NaCN and 1.9 kglt respectively. Following the incorporation of lead nitrate, overall gold extraction was increased from 89.2% to 91.1 % but no change was noticed in cyanide consumption. The gross profit is $CDN 988,000 per year.

Jan 1, 1999

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers' catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023

By J. Kang

Supercritical fluid extraction (SFE) has became an attractive alternative technology to be a new process to recover metal, of which can be substitute the existing Leaching/Solvent extraction processes. Solvent extraction of metallic ions is a technically important and also well-established process that is used in the chemical and hydrometallurgical industries.1 Solvent extraction techniques use the chelation of metallic ions dissolved in liquid solution with organic ligands. Conventional solvent-extraction technique needs large amount of organic solvents and often creates environmental problems.2 More environment-friendly technology is needed nowadays, and there have been increasing attentions to extract metal ions by SFE. CO2 becomes one of the most notable alternative organic solvents due to its nonflammable, nontoxic, nonpolluting, and relatively inexpensive properties with its moderate critical point (73.8 bar, 31.06 °C). Many works have been reported in metal extraction under the supercritical CO2 (scCO2) solvent.3-5 In this study, to recover cobalt from wastes especially from spent lithium ion battery scrap, we selected two ligands ? Cyanex 272 and DEA (diethylamine) for the metal extraction in scCO2. Cyanex 272 is a commercially available extractant along with its series, Cyanex 301 and Cyanex 302. Smart and coauthors measured the metal extracting abilities of these three extractants, and found that Cyanex 301 and Cyanex 302 extracted metal ions much better than Cyanex 272 in the scCO2 solvent.10 The pH of water contacted with high pressure CO2 (70-200 bar, 25-70 oC) is about 2.8-2.95 based on the calculation and the measurement.6-7 Cyanex 272 is known to be less effective as a metal extractant in this low pH environment compared with other Cyanex series. However, when DEA is added to metal extraction reaction with Cyanex-272, DEA works as a strong base to Cyanex 272 converting Cyanex 272 to a deprotonated form (Figure 1), which results in an easy formation of metal complex and the enhanced extraction rate of metal ion.8 Therefore, the purpose of this paper is the metal extraction from spent lithium ion battery waste using scCO2 with Cyanex 272 and DEA.

Jan 1, 2010

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

By M. L. Bricker

The Jim Bridger Mine is operated by Bridger Coal Company and is located in Sweetwater County, 35 miles (56 km) northeast of Rock Springs, Wyoming (USA). The general location of the mine site is shown on Figure 1. Bridger Coal is a joint venture of NERCO Coal Corp, the operator, and Idaho Energy Resources Company. The permit boundary encompasses in excess of 20,000 acres (81 km2) and is nestled against the western side of the Continental Divide. Production started on July 3, 1974, and the mine has produced approximately 90 million tons (82 million t) while moving approximately 450 million cubic yards (344 million m3) of virgin earth. Annual production averages 5 to 7 million tons (4.5 to 6.4 million t) of run-of-mine coal. Coal is consumed on site by the Jim Bridger Power Plant, a 2,000-megawatt generating station, and the electricity is transmitted to the Pacific Northwest power grid (Oregon, Idaho, Northern California, etc.).

Jan 1, 1991