Search Documents

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By W. J. Bronkala

Dense-medium circuits have been installed in many mineral treatment plants since its, original development about thirty years ago. In the intervening, period the process has been thoroughly evaluated and many innovations have been introduced. The Heavy Density. Cyclone is one of the newer systems which has extended the operating range of this process to 65 mesh size. Several different finely divided materials have been used to produce the separating bath but nearly all new plants use a ferro-magnetic medium. The, advantages of magnetic medium include: 1. Smaller recovery plant 2. Lower cost recovery plant both in initial and operating cost 3. Excellent medium stability 4. Dependable medium supply at reasonable and stable cost. Magnetic separators are used to recover this magnetic medium and the smaller plants and lower operating costs are directly related to their use.

Jan 1, 1964

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By J. H. Hill

The globalization of mineral markets and intense competition in downstream mineral-consuming industries such as transportation, agriculture, and construction are requiring raw materials suppliers to innovate, improve quality, invest in new technology, and control costs. Mineral specifications are becoming more refined, and pressure to improve products is felt from increasing numbers of competing producers, substitute materials, customers, and regulators. As a result, engineered mineral products are becoming more like manufactured ones in terms of cost structure, differentiation, and the importance of market driven, customer specific product development. Engineered mineral products are defined as those where the costs of refining and upgrading outweigh those of conventional mining activities (blasting, crushing, classification, haulage etc.), and where close control of physical and chemical parameters is required for customers' processing and manufacturing applications. This includes industrial minerals such as calcium carbonate, kaolin, mica, specialty oxides, talc, and some metal powders. It excludes most metals and bulk commodity materials such as gypsum, lime, sulfur, and soda ash. Engineered mineral products are utilized in common household goods, and are at the forefront of industrial materials engineering in plastics, ceramics, composites, glazes, coatings, and construction materials. As a group, they introduce interesting questions to the minerals firm. Advanced materials or basic? Diversify or specialize? What are the implications of advanced materials and for mineral markets, and most importantly, where can the producer look for long-term value, volume, and profits?

Jan 1, 1993

By L. A. Arrington-Webb

The International Standards Organization (ISO) 9000 series of quality standards was published in 1987. First initiated by the British in the mid-1970's to assure the quality of British goods and services. ISO 9000 certification demonstrated the capability of a supplier to meet the requirements of the customer. Thiele Kaolin Company has invested considerable time and money achieving and maintaining ISO 9002 certification. Through a regimen of process control and documentation, routine audits, and a commitment to quality management, this kaolin producer continues to be a competitive pigment supplier in a world-wide market.

Jan 1, 1997

By C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self-advancing hydraulic supports. U.S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology has greatly increased productivity. Past trends are used to predict future technological directions.

Jan 1, 1997

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Alejandro Sanz, Juan Luis Magro, David Mazeyrie

The Hampton Roads Bridge-Tunnel Expansion Project (HRBT), initiated by the Virginia Department of Transportation (VDOT), will add two new 1.5-mile TBM bored tunnels to the two existing immersed-tube tunnels between artificial islands, part of the connection between Norfolk and Hampton under the Hampton Roads Harbor in Virginia, USA. The new bored tunnels will be built by Hampton Roads Connector Partners (HRCP), a joint venture of Dragados USA, Vinci Construction, Flatiron Constructors and Dodin Campenon Bernard. This paper covers technical discussions that led HRCP to select a Variable Density TBM to address the challenges of this tunnel project, including but not limited to (i) the diameter of the bore: a 46 feet (14.04 m) diameter machine that constitutes the second-largest TBM ever used in the United States; (ii) shallow ground-cover under the water table; (iii) challenging and varying geology along the alignment, with mixed-face conditions and different types of ground modification zones; and (iv) the high TBM operating pressures required—all these and other challenges in a sensitive marine environment.

Jun 13, 2021

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979