Search Documents

By J. M. Carter, Rodney H. Sergent, L. E. Kun, J. T. Pressly

Underground mine service water in South Africa is used for dust suppression and cooling the environment as well as the pneumatic rock drills. Although the chilled water is not intended for potable use, it is often used as drinking water by mining personnel. Furthermore, droplets sprayed are liable to be inhaled. The water is recirculated on a continuous basis and is a potential source of infection by intestinal microorganisms or water-borne diseases such as cholera or typhoid. In order to protect the health of the underground workforce it is customary to disinfect the chilled service water, The bacteriological quality of the water is monitored by enumerating total aerobic bacteria (TAB), total coliforms (C C) and Escherichia coli (E Coli). E coli is an indicator of human faeca_l __ - -- contamination, The bacteriological standard specified by the Anglo American Corporation for mine service water is less than 3000 TA B per 100ml, less than 2 CC per ml and the total absence of E Coli. There are several disinfecting agents available for use. Among these are UV irradiation, ozone, chlorine dioxide and compounds that produce hypobromous and hypochlorous acids. Historically, the methods of treatment have been chlorine based and include the use of gaseous chlorine (surface installations only), calcium hypochlorite granules or tablets, chlorinated cyanurate tablets, sodium hypochlorite solutions and hypochlorite produced by electrolysis.

Jan 1, 1991

By J. H. Gasper

A cost analysis for two alternative contour mining methods is performed to compare their results. The methods evaluated are: 1) Front-End Loader/Truck Haulback and 2) Scraper Haulback. Before performing these analyses, output requirements and equipment needs are found based on integrating geometric limitations with material properties. The final geometric design establishes limits on clearances, congestion problems and grades (with associated running surface materials). All calculations are kept practical, with assumptions clearly stated. The cost analysis is a unique, easily utilized compilation of several different approaches incorporating cost engineering principles. The strengths of each are welded into a cohesive entity once again aimed at practical application. The results are presented in tabular form.

Jan 1, 1992

By John E. Dreier

The Pachuca-Real Del Monte district, Hidalgo, Mexico (Figure 1) has produced roughly 1,500,000,000 oz Ag., 6,000,000 oz Au. and minor Pb., Zn, and Cu from about 100,000,000 tons of ore since discovery early in the 16th century. Production has come from epithermal vein deposits that have been up to 8 km in length, 650 m in vertical extent and 45 m in width but which averaged 200-400 m in length and vertical extent and 2-4 m in width. Ore deposits occur through-out an area about 12 km E-W by 10 km N-S (Figure 2) and between the elevations of 2000 and 2800 m above sea level. The deposits occur as shoots in the veins and terminate laterally where the veins narrow, upward where the veins pinch out and downward where the veins decrease in silver con-tent to below the cut-off grade; the veins are known to extend 500 m below the bottoms of the ore bodies and probably extend to much greater depths. The district lies wholly within a mid-to-late Tertiary volcanic rock sequence that is made up principally of andesite and dacite lava flows and flow-breccias. Although the bottom of the sequence is not exposed in the district, stratigraphic constructions indicate the volcanic rocks to have an aggregate thickness of 2000 to 2500 m. Structurally, the area is characterized by gentil warping and normal faulting of the volcanic rocks. Pre-ore modifications to the volcanic rock sequence consisted mainly of faulting along west-trending, south-dipping normal faults and north-trending high-angle faults.

Jan 1, 1978

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

The survival chances of trapped miners in underground mines depend on how quickly they can be located and rescued post-accident. During entrapments, emergency rescue is highly desired but can be hindered by the lack of positioning information when a fit-for-purpose missing-person locator system is not available. Various types of missing-person locator systems are available to aid search-and-rescue operations. From the wide range of the available systems, selecting the most suitable one becomes the next challenge. The available systems have not been measured if they are fit-for-purpose or not, and to what situation. This study proposes user requirements that can be used as a guideline to facilitate the system selection process. These user requirements provide a framework for the design and development of a fit-for-purpose missing-person locator system. The user requirements can also be used for evaluating the performances of a particular system, predict its success, and also drive future research toward developing new technology to enhance the capabilities of the current systems.

Apr 1, 2024

By A. Jahedsaravani, M. Massinaei, M. H. Marhaban, N. Mehrshad, M. I. Saripan

"It is well known that froth visual features reflect the operating conditions of the flotation process, so that being able to accurately obtain the froth properties is the most significant criteria to optimize and control this process. Froth segmentation is a useful procedure that can determine the bubble size distribution. Several algorithms have been proposed in this field, but marker-based watershed transform shows the best performance. In spite of this fact, the algorithm suffers from oversegmentation in cases when the flotation froth includes large bubbles along with small ones. In the paper, the marker-based watershed method is modified to prevent oversegmentation of large bubbles. The developed algorithm is validated using some froth images captured at different operating conditions, so the results indicate that the method can segment the mixture of big and small bubbles effectively.IntroductionFroth flotation is a widely used process for separating valuable from gangue minerals. Effective control of flotation circuits has a dramatic effect on overall performance of a mineral processing plant. In most flotation plants, process operators monitor the froth surface visually and make adjustments to process parameters based on their interpretation of the surface appearance and their idea of the appearance of an ideal froth. However, due to natural complexity of the flotation process, achieving optimal control is often not possible for human operators.In recent years, attempts have been made to control the flotation circuits using machine vision systems (Moolman et al., 1995; 1996a,b; Bartolacci et al., 2006; Kaartinen et al., 2006; Vanegas and Holtham, 2008; Aldrich et al., 2010). The froth bubble size distribution is the most significant control variable that reflects the operating conditions in a flotation machine. To date, a number of approaches have been proposed for bubble size measurement from froth images, including segmentation (Sadr-kazemi and Cilliers, 1997; Wang et al., 2003; Mehrshad and Massinaei, 2011), texture spectrum (Nguyen and Thornton, 1995), wavelet (Liu et al., 2005), an improved texture spectrum approach, a method based on binary images (Lin et al., 2008) and, finally, using interfacial morphological information (Yang et al., 2009)."

Jan 1, 2015

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By Karoly (Charles) Kocsis, Kyle A. Scalise

Understanding the climatic conditions in underground mines is necessary for efficient ventilation design, cost savings, and to ensure the health and safety of mine workers. Large volumes of ventilation and climatic data including air volume, barometric pressure, dry bulb temperature, and relative humidity were collected at active underground precious metal mines in Nevada, which allows for the determination of wet bulb temperature and other key parameters. Through the utilization of neural networks, the wet bulb temperature at the bottom of the intake shafts is predicted, while taking into account the “thermal flywheel effect” (TFE). Wet bulb temperature is one of the most important climatic parameters to model and understand because it significantly affects the work conditions and the cooling capacity of the ventilating air. The accurate prediction of the dry bulb and the wet bulb temperatures at the bottom of intake shafts is critical when assessing the climatic conditions in future underground mines and deciding onwhether a cooling system is needed to assure adequate working conditions throughout themine. By utilizing accurate predictions of wet bulb temperatures and other climatic parameters, mine personnel will be safer as reported by Bluhm et al. (2003), and a more accurate ventilation design can be achieved resulting in major cost savings for underground mines.

Mar 3, 2021

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By F. Calizaya

This study summarizes the ventilation requirements for a highly mechanized P.T.Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The Deep Ore Zone (DOZ) is a copper-gold deposit being developed underneath the current Intermediate Ore Zone (IOZ) mine. One of company's current plans is to prepare this mine for a steady oreflow of 25,000 tpd by year 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 1998

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By P. A. Hendricks

The surface coal mining industry in the United States employs over 50,000 people and is responsible for 60% of domestic coal production. This represents a very significant contribution to our national economy and an important source of highly skilled and well paying jobs. The U.S. Bureau of Mines (USBM) has targeted surface mining as an important research priority to reduce the social and economic costs associated with surface mining injuries and fatalities. USBM safety research focuses on the development of technologies that can enhance productivity and reduce mining costs through a reduction in the number and severity of mining accidents. This report summarizes a number of completed and ongoing research programs that address a broad range of surface mining safety problems. Research methods are described, and research products which are suitable for industry implementation are highlighted.

Jan 1, 1994

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Jan 1, 1997

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By Arash Nikvar‑Hassani, Timothy Batchler, Lianyang Zhang

Recently, a new hybrid geopolymer/biopolymer (GP/BP) cementitious material was developed for improving the performance of pumpable roof supports in underground mines. This study demonstrates the application of the hybrid GP/BP cementitious material and validates its effectiveness in full-scale. In this regard, eight (8) full-size (0.61 m diameter and 1.52 m height) cribs were produced in collaboration with Minova International Ltd and tested at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) Laboratory. These full-size cribs were produced with different material configurations to evaluate the effect of water to solid (W/S) ratio, Portland cement (PC) content, and BP dosage. The results demonstrated and validated the effectiveness of the hybrid GP/BP cementitious material in increasing the peak and residual bearing capacities of pumpable cribs and eliminating the issue of deterioration when exposed to air compared with the conventional Portland cement/fly ash (PC/FA) cementitious material currently used in practice. On average, the peak uniaxial compressive strength (UCS) and the highest residual UCS after peak of the full-size cribs produced from the hybrid GP/BP cementitious material are 1.90 and 1.33 times of those of the PC/FA-based full-size cribs by one company and 2.32 and 1.66 times of those of the PC/FA based full-size cribs by the other company, respectively.

Feb 6, 2024

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By Frederick B. Henderson

On 10 August 1976, The Geosat Committee was organized in Denver to institute The Geosat Program. This program is an industry backed effort to evaluate and help select optimum space remote sensing systems for geological purposes. It is believed that the recommendations of The Geosat Committee can be supported by industry as additional exploration tools which can materially benefit industry and the Nation with respect to our energy and other natural resources needs. Appended is a general summary of The Geosat Committee Organizational Meeting and general review of The Geosat Program. The Geosat Workshop Report. The Geosat Committee, and The Geosat Program will be reviewed at a special afternoon session, Friday, 3 September.

Jan 1, 1976