Search Documents

By K. Bunney

A high-pressure laboratory elution rig was commissioned to simulate industrial Zadra and AARL elution conditions for the stripping of gold, silver and mercury from loaded activated carbon. It was found that cyanide was essential for the efficient elution of both mercury and silver, while gold was found to elute most effectively in hot, low-ionic strength solutions. Therefore, the standard AARL-type elution, which implements a cyanide soak and water elution, results in a lower recovery of mercury and silver from the carbon. No single set of conditions was found whereby gold, silver and mercury can all be effectively eluted in a single step. However, sequential elution conditions can efficiently recover all metals and provide a potential approach for separating these metals.

Jan 1, 2010

By Greg R. Wheeler

Few members of the general public have a clear understanding of mineral resources. Most people do not know how minerals are mined or why they must be extracted from many diverse locations. Many people acquire knowledge of mineral development from mass media sources with incomplete details or obvious anti-mining bias. The California Mineral Education Foundation was formed in 1991 to provide educational opportunities for the public and industry. There have been major changes in earth science teaching requirements for kindergarten through 12th grade (K-12) curricula since the passage of California Senate Bill 813 in 1983. Model graduation standards, curriculum standards and the state science framework mandate substantial coverage of geoscience topics. The California State Commission on Teacher Credentialing has completed changes in multiple subject and single subject science credentials which will require more geoscience preparation for all teachers. The need for pre-service and in-service education in geoscience is at an all time high. Teachers must have continuing education to maintain their credentials and many are now seeking information in geoscience. The California Mineral Education Foundation designed and conducted the California Mineral Education Conferences held in August 1991 and 1992. The conferences involved lectures and field trips on mining geology, environmental problems and political concerns. Master teachers were employed to share how they get across mineral resource concepts in the classroom. Ninety-six percent of the participants stated that they had changed to a more positive perception of mining after taking the three day course.

Jan 1, 1995

By J. R. Arnold

The problem of recovering gold from a cyanide solution has been plaguing metallurgists since the cyanidation process was discovered in Glasgow, Scotland.1 The "perfect" method has never been found and this paper will not purport to fill that gap. But we, at Gold Fields, feel that we have developed a workable, cheap and efficient method of producing a refinery - ready product that has several distinct advantages over conventional electroplating techniques. The Gold Fields replating system is presently being used at their Ortiz and Mesquite operations. In short, the system electroplates the gold out on stainless steel wool, instead of mild steel wool as is usually done, then replates the gold by reversing the current onto stainless steel plates. By doing this the steel wool can be reused many times, the gold can be scraped off the plates cleanly and quickly, the operating costs are reduced and the slag production is greatly reduced.

Jan 1, 1986

By D. Olsen

The paper discusses the legislative and practical approach adopted to problems of management of environment in relation to coal mining in a very sensitive area of the south coast of New South Wales. The environmental problems are complicated in this area due to multiple and very often conflicting land usages. The environmental approach in relation to water quality maintenance, noise control and air quality is discussed and methods adopted meet stringent requirements. Requirements of New South Wales Regulations on Environmental Impact Statements (EIS) are described.

Jan 1, 1988

By Stanley M. Moos

The Pueblo Viejo gold/silver mine, located in the Dominican Republic, started production in early 1974 processing ores averaging 4 g/tonne gold and 20 g/tonne silver at a rate of 7,250 tonnes/day. The ore milled is a silicified siltstone with average work index of about 8 that occurs as an extensive oxide capping of a primary sulfide orebody. The sulfide ores are refractory to conventional treatment process and extensive research work is now in progress to develop a treatment process for them. The ore deposit has a long history having been mined by the indigenous Arawak Indians (for some time in the early sixteenth century) prior to the arrival of the Spanish and then by the Spaniards. In the early 1950?s, Italian engineers attempted to process the sulfide ores. Mining by the Indians and Spanish was abandoned because of low grade and little coarse gold in the oxide ores and by the Italians because of the refractory nature of the sulfide ore. In 1969, Rosario Resources geologists discovered that there existed sufficient reserves of oxide ore for a viable mining operation and accordingly, the plant was designed, built and brought into production.

Jan 1, 1979

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022

By R. C. Bunge

The success of a mineral separation is commonly assessed from the separation curve, a graph of the recoveries achieved versus the corresponding separator settings. Two values characterize the curve, first the "splitpoint" which is the separator setting that produces a recovery of 50%, and second a measure for the separation sharpness. The splitpoint represents the "mean" while the measure for the separation sharpness represents the "scatter". In modelling the performance of crossflow separations the mean particle behavior is calculated from the force equilibrium that determines the particle trajectory which leads to a deterministic model. The scatter is then represented by a stochastic model. This presentation discusses the modeling of a crossflow separation and some implications with separation theory. The model is shown to successfully predict the performance of a magnetogravimetric separator.

Jan 1, 1992

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By Bobby C. Carson

INTRODUCTION The National Park Service is entering the seventh year of monitoring caves for the presence of radon and radon daughter products. The purpose of this paper is to summarize the radiation monitoring program at Mammoth Cave National Park, and to present some of the results of this program. Mammoth Cave National Park completed five years of collecting data on May 1, 1981: although Mammoth Cave encompasses approximately 361 km of underground passageways, this paper will concentrate on only a 2.2 km section of the cave known as the Historic Tour. Included in this paper is a discussion of the methods the Nations Park Service uses to protect employees from exposure to alpha radiation. MONITORING METHODS The National Park Service monitors cave atmospheres utilizing the procedures provided by the Mine Safety and Health Administration in their Radiation Monitoring Training Manual (Anon., 1976). This procedure is described as the Kusnetz Method (Kusnetz, 1956) of radon daughter monitoring. Due to the length of the tours at Mammoth Cave, it has been determined to be the most practical procedure. The Historic Tour is a 2.2 km (1.4 mile) loop through passageways ranging in size from 18 m high by 12 m wide, to 0.9 m high by 0.6 m wide. Seven five minute walking samples were taken for this cave tour by drawing at least 10 1 of air through a 25 mm fiberglass filter utilizing a Monitaire Sampler Pump. The radon daughter concentration levels were determined using an alpha scintillation counter to measure the alpha activity on the filter paper. The Monitaire Sampler Pump was calibrated each day prior to monitoring the cave tour and the scintillation counter was calibrated by procedures described by the Mine Safety and Health Administration (Beckman, 1975) at six month intervals. Guidelines established by the National Park Service and approved by the Mine Safety and Health Administration require weekly sampling when the average working level exceeds 0.30 (NPS-14, 1980). A working level is an atmospheric concentration of radon (Rn-222) daughters which will deliver 1.3 x 10 5 MeV of alpha energy per liter of air in decaying through Ra C' (Po-214). The Historic Tour has continually exceeded the 0.30 working level average and has been monitored weekly. Generally, only radon daughter working level data has been collected on the Historic Tour due to limited personnel. However, other special measurements of the uncombined fractions of radon daughters with wire screens, tsivoglou method for radon daughter sampling (Thomas modification, 1970), and thoron daughter monitoring. These special measurements have not been routine due to time limitations involved in radon daughter sampling of other occupied portions of the cave. SUMMARY OF DATA The Historic Tour has been the most consistantly monitored tour since elevated levels of alpha radiation were found to exist at Mammoth. Cave. It is also the only natural entrance to the main sections of the cave and provided an opportunity to study man made actions upon the natural entrance. For these reasons the Historic Tour was isolated for study. Beginning October 10, 1977, and ending November 20, 1977, a pilot project was undertaken involving the Historic Tour and the practice of covering the natural entrance to this tour with sheet metal in the winter months. The purpose was to study radiation levels on the Historice Tour while the covers were on and off the natural entrance. In this pilot project, comparisons were made with incast air with covers on and off the entrance, and outcast air with covers on and off the entrance. TABLE 1 Incast air Mean W.L. Covers on . . . . 1.46 W.L. Increased 54% Covers off. . . . 0.67 W.L. when covers on Outcast air Mean W.L. Covers on . . . . 1.33 W.L. Decreased 5% Covers off. . . . 1.40 W.L. when covers on The natural entrance was artificially covered in the winter months (Yarborough, 1978) to protect the visitor from the extremely cold incast air, in the first four years of monitoring. The data in Table 1, illustrated in Figures 1 and 2, shows that this action increased the radon daughter working levels on the Historic Tour by 54% when the covers were on the entrance and the airflow was incast. While the air flow was outcast at the natural entrance, it made little difference as to whether the entrance was closed or open. Some interesting findings were observed when

Jan 1, 1981

By S. Managi, M. C. Williams, N. H. Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key-technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate or hydroxide electrolyte. Since a pure stream of CO2 is produced the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology. INTRODUCTION The DCFC has been under development for many years. It was researched as early as 18961), but an intense research and development is necessary to realize its potential. William W Jacques, a US electrical engineer and chemist, described a DCFC in 1896 in US Patent 555511 for a “Method of converting potential energy of carbon into electrical energy”. Jacques used coke electrodes in a molten NaOH electrolyte. Molten carbonate fuel cell (MCFC), solid oxide (SOFC) or hydroxide electrolyte (AFC) technologies can be used as the basis for the DCFC technology. A schematic of the direct carbon fuel cell in the MCFC mode is shown in Figure 1. The molten carbonate fuel cell operates at approximately 650°C (1200°F). The high operating temperature is needed to achievesufficient conductivity of the carbonate electrolyte, yet allow the use of low-cost metal cell components. A benefit associated with this high temperature is that noble metal catalysts are not required for the cell electrochemical oxidation and reduction processes. For the hydrogen reaction the half-cell electrochemical reactions are

Jan 1, 2019

By Colin Connors

Cemented rockfill is a key component in the success of underground mining at the Jerritt Canyon Joint Venture. The Murray and SSX mines are characterized by relatively poor rock mass quality, and the goal of complete mining recovery makes maintaining a high quality backfill product vital to the safety and efficiency of the mining operations. A large portion of the ore production from the Murray mine originates from drifting under backfill. Modelling studies performed to investigate induced loading of the backfill were used to develop engineering specifications for the backfill material. Operations history has shown an almost 100 percent stability of the backfill when mining is carried out beneath it. The volume of backfill required each year (approximately 300,000 tons) and the required cement content have a significant impact on the total mining costs. The potential for cost savings associated with higher replacement of cement with Type "C" fly ash and the implementation of a backfill strength management strategy were therefore evaluated.

Jan 1, 2001

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

By Lianhui Jia, Yali Han

"The key technologies of a large rectangular pipe jacking machine with dimensions of 10.12m × 7.27m (width x height) include selection of rectangular cross-section cutting modes, analysis on the strength and stiffness of the rectangular shield, integrated control of electro-hydraulic proportional thrust systems and ground conditioning for excavation are presented in detail in this paper. These key technologies have been successfully applied and verified on site during tunneling, providing a new concept for the building of large rectangular traffic and pedestrian tunnels in urban areas for the future.1 INTRODUCTIONIn the past, underground tunnels were mainly used for drainage, sewage, utilities, metro tunnel, etc. and most of them had circular cross-sections. Recently, as a result of economic development, gradually accelerating urbanization process and diminishing ground space, underground tunnels have already become a new trend for urban underground space utilization. Due to the heavy traffic flow, the demands for rectangular cross-section underground tunnels, such as pedestrian underpass and road tunnel, are increasing gradually.The Rectangular pipe jacking machine (hereinafter referred to as RPJM) was firstly developed in Japan for the construction of metro station, pedestrian underpass, underwater tunnel by-passes, etc. Kazunaki Kawai et al. introduced a RPJM developed and manufactured by KOMATSU in 2002 [1]. Tosikazu Kubota et al. confirmed the rectangular tunnels’ superiority to circular tunnels with regard to larger inner cross-section and lower construction cost in their RPJM construction reports [2]. Compared to circular pipe jacking machines, a RPJM also has the merits of a higher inner tunnel space utilization ratio and is able to excavate in shallow overburden areas. As shown in Figure 1, the effective area of a rectangular tunnel is more than 20% higher than that of an equivalent circular tunnel."

Jan 1, 2016

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By Cesar Carrasco, Heath Arvidson, Mark Forster

Block models built to represent the geology and rock characteristics of mineral deposits represent huge complex data sets, which form the basis of strategic and business planning, and public reporting of Mineral Resources and Mineral Reserves. Recent advances in cloud computing and database technology developed for the Internet of Things offer a different way of working with these critical data sets. Enabling a cloud based, open data structure with high performance data analytics capability presents a compelling improvement in governance and a democratization of ore body knowledge that can lead to automation use cases that support the digitalization of mining.

Jun 25, 2023

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018