Search Documents

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

By S. Lee, F. Campero

"Past heap leach design has evaluated hydrodynamic parameters based on a uniform particle size of heap material, but has ignored the equal importance of the instability of fine migration within heap stack in the beginning stages of the irrigation process. The proposed probabilistic model evaluates internal fine erosion and segregation potential of well-graded crushed ores by considering the entire particle size distribution shape and site compaction degree. Using this model, unsaturated flow model parameters were successfully evaluated based on synthesized soil-water characteristic curve (SWCC). Additionally, one-dimensional unsaturated transient flow modeling with Hydrus 1D® showed that the different recovery efficiencies of heap material under unsaturated flow patterns depending on the particle size distribution and compaction degree of heap material. Agglomeration preprocess employed by most heap leach sites can reduce the potential of fine erosion within heap material significantly, but internal stability of crushed ores and hydrodynamic-based analysis of heap material’s pore structure is equally important in the prescreening stage in order to improve efficiency of the heap leach and avoid a costly agglomeration process. INTRODUCTION Accurate estimation of heap leach recovery is a difficult task due to the variety of design parameters that need to be considered - such as geochemistry, hydro-dynamics, and geotechnical design aspects, most notably particle size distribution through the process of agglomeration. After agglomeration techniques were introduced to heap leach design, the influence of particle size distribution and compaction degree in enhanced heap leach recovery has been neglected. The main purpose of agglomeration is to prevent fine segregation and internal erosion during and after heap stacking for well graded crushed ores, which will eventually diminish heap reach recovery. Recent studies show that agglomerated heap materials that had been consolidated at 10 meters below heap surface can release the fines after contact time with lixiviant to the compacted heap material and produce poor drainage performance (Milczarek et al, 2013). It must be noted that engineers and practitioners should investigate feasibility of agglomeration benefit prior to heap leach design because the agglomeration process can incur up to 20 or 30% of project costs. Internal stability of stacked heap material is mainly governed by the particle size distribution of crushed ores. Depending on this stability, segregation and internal erosion of fines can be mitigated by the application of moderate compaction effort during heap construction. Investigation of segregation and internal erosion potential therefore takes precedence for well graded crushed ore since reaction time and contact area with lixivant are greater in finer ores."

Jan 1, 2016

By Bartłomiej Bursa, Paweł Stefanek, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

The article presents the main functionality of the DSS class system for monitoring and stability assessment of tailings storage facilities. The presented demonstrator was deployed on the example of the Żelazny Most reservoir - the largest active facility of this type in Europe and the second one in the world. Considered a high-risk structure, it demands a system capable of online analysis of big data from various sources using machine learning, 3D modeling, or GIS mapping with the functions of interactive time-spatial analysis. In this paper, we present a complex calculation module with an integrated user interface.

Jun 25, 2023

By A. R. Conroy

Microscopic observation of physical and chemical changes which take place in various materials under conditions of elevated temperature and controlled atmosphere can often yield valuable insight into the fundamental physical-chemical reactions which control processes in which these materials play an active role. The technique of high-temperature microscopy thus becomes an important tool for basic and applied research in pyrometallurgical and allied fields. Investigators have long been aware of this and through the years have applied the technique to a wide variety of problems. However, up to this time, application has been on a rather limited scale due to the high initial cost of equipment and the relatively low rate of production of data resulting from the complexity of the apparatus and attendant problems in manipulation.

Jan 1, 1964

Microwave pretreatment can improve grindability by weakening brittle particulate material prior to size reduction. The differential thermal expansion experienced by multiphase materials during rapid heating can also promote damage in the grain-boundary region, which may ultimately translate into enhanced liberation. The effect of microwave pretreatment on the breakage characteristics of different ores has been studied using the Ultrafast Load Cell. The energy accumulated during impact (fracture energy) and the particle stiffness have been measured for untreated and microwaved ore samples. It has been observed that microwave pretreatment can weaken brittle multiphase particulate material, as observed by reductions in fracture energy and increase in damage.

Jan 1, 1996

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By J. Hanna

Four Ca-bentonitic clays from Alabama were evaluated for use in Diammonium Phosphate (DAP) or Urea Ammonium Nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium exchanged Alabama clays, were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Na-modified clays, prepared according to the TVA soda ash method, was as good or even better than those observed for the Mg-, Na/Mg-or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1989

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023