Search Documents

By Y. Lahaye, O. Martinsson, B. I. Palsson

"Four main and three minor rare-earth-element (REE)-bearing minerals were identified and quantified in the Kiirunavaara apatite iron ore tailings using optical microscopy, an electron probe microanalyzer (EPMA) and a mineral liberation analyzer, and their chemical compositions were analyzed by the EPMA and laser ablation inductively coupled plasmamass spectrometry. REEs are shown to be contained in the minerals apatite, monazite, allanite, titanite, zircon, thorite and synchysite. In zircon, thorite and synchysite, they occurred in only trace amounts and contributed limited amounts to the total REE budget, and these are consequently of minor importance. Monazite occurred as inclusions in apatite and as free particles, 90 percent liberated. Allanite occurred to some degree in mixed grains with magnetite but also as free particles. Monazite mainly reported to the apatite concentrate, while allanite and titanite largely went to the tailings, the latter preferably to those fractions smaller than 38 µm. The amount of titanite in the finest tailings fraction was 2.3 weight percent, containing close to 1 percent REEs, with heavy rare earth elements (HREEs) making up 28 percent of the total REEs. However, a texturally distinct group of titanite grains showed an HREE/REE ratio of up to 67 percent. Furthermore, titanum dioxide analyses indicate that titanite is preferentially released into the tailings from the secondary magnetic separation step in the concentrator. Our data therefore suggest that titanite, occasionally enriched in HREEs, can be extracted from the processing stream and might thus be considered a new source for REEs at Kiirunavaara and similar deposits.IntroductionDeposits of apatite iron ores are the major source for iron in the European Union and are exploited by Luossavaara-Kiirunavaara AB (LKAB) in several mines in the Kiruna-Malmberget area in northern Sweden. Kiirunavaara is the largest of the apatite iron orebodies in Sweden, comprising more than 2 Gt of iron ore with 60 to 68 percent iron (Fe). At the end of 2015, the total accumulated production of crude ore from openpit and underground mining since the start of mining was 1,566 Mt, with ore reserves of 644 Mt grading 46.3 percent Fe (LKAB, 2016). The deposit defines a steeply dipping tabular body, approximately 6 km long and up to 180 m thick, extending at least 1,500 m below the surface. It is situated in the middle part of the Palaeoproterozoic Kiirunavaara Group of volcanic rocks and follows the contact between a thick pile of trachyandesitic lava and overlying pyroclastics (Martinsson, 2004)."

Jan 1, 2017

By J. D. Miller

The effects of operating variables on water transport to the over- flow, classification of hydrophilic particles and the recovery of copper and molybdenum from a low-grade porphyry ore are presented. Recoveries of copper and molybdenum exceeding 90 percent at a grade of 8 percent Cu and 0.2 percent Mo were realized for minus 100 mesh (1 49 µm) material at retention times of less than 500 milliseconds. The rapid rate of flotation and the effective separation of fine particles for an air sparged hydrocyclone appear to be due to directed interaction of particles in a high force field with numerous freshly formed small bubbles. This interaction occurs in the swirl flow developed by the system and is analyzed in terms of collision and induction time phenomena.

Jan 1, 1982

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Steve Skelhorn, Dan Ifrim

"A tunnel project poses many challenges; the operation of the Tunnel Boring Machine (TBM) being one of them. Mechanized tunneling is known as a safe and effective alternative to other methods in terms of schedule and cost; however, efficiency can be severely affected by a bad TBM selection and qualification and employment of inexperienced operators. The success of a mechanized tunneling project involves a comprehensive and interdisciplinary consideration of all contributing factors such as TBM technical specification and selection, TBM design and procurement including ancillary equipment and tunnel linings. The tunnel equipment selection along with the operation can make or break the project. The objective of this paper is to address the importance of the skills and qualifications of the TBM crew with particularity to the TBM Operator. The study includes the Owner and Consultant involvement in the selection and pre-qualification of the TBM crew and specifically the TBM operator as well as the role of Contractor and TBM manufacturer in TBM operator training. This paper also analyzes the possibility of issuing a TBM operator certification, and discusses the benefits and significance of periodic training and certification programs. INTRODUCTION Training in the tunneling industry is not a new topic. The industry continues to evolve and become more complex with technology advances and expansion of mechanical tunnelling to mechanized shaft construction, large diameter drilling and mining industry applications. The need for professionals trained to operate mechanized tunnelling equipment is ever increasing, while there is a significant number of veterans who will be ageing out in the next 5 years. Consequently attracting young professional is a very important aspect of sustaining a qualified pool of professionals. For any given tunnel project, the owner and the engineer spend up to several years, studying the ground conditions during preliminary and final design. Post contract award the contractor spend additional months studying the ground again to develop the optimum means and methods for construction. All this time and money spent at the beginning of the project has the purpose of developing the optimum tunnel design, assessing the risk associated and implementing mitigation measures to reduce risks to acceptable levels. Following the tunnel design process, sophisticated TBMs are being specified and sourced to ensure the best tool for the job. The question raises here: Are there available experienced/trained professionals capable of operating these sophisticated machines?"

Jan 1, 2016

By W. E. Crandall

The Star-Morning mine is a. 1000-ton-per-day lead-zinc producer located in the easterly part of the Coeur d'Alene Mining District of North Idaho. The property includes both the Star and Morning mines which are located on the westerly and easterly portions of the same complex of veins. The mine is 70% owned by the Bunker Hill Company (Gulf Resources, Inc.) of Kellogg, Idaho, 30% owned by Hecla Mining Company, and operated by Hecla Mining Company with head-quarters in Wallace, Idaho. One of the characteristics of mines in the Coeur d'Alene District is that many of the ore bodies extend to very great depths. The Star is no exception, but rather a leading example. The complex of near vertical veins and ore shoots extend some 7000 feet below the surface at present, with a maximum strike length of about 4000 feet. Ore has been mined on 20 separate veins and ore structures. More than 50 miles of headings have been driven and nearly 23 million tons of ore mined since the Morning mine started in.189S. The problems of mining at such depths are formidable temperature on the bottom level is 1100 F and high humidity problem. Pressure from the sheer weight of rock is as high foot. This paper will deal with providing a new access to the deeper levels of the mine and the installation of a hoist and related items to service these levels. By the time development had reached the 7100 level (Figure 1), it became apparent that a different 'hoisting system was going to be necessary if we were going to continue to mine at a profit. The main shaft extended to the 4000 level at which point a ?:3100"'foot winze shaft provided access to the 7100 level. The two hoists were limited to handling 3-ton payloads at 1200 to 1500 feet per minute. Some ores are still produced from above the 4000 level but as these ore reserves become depleted the hoisting of the desired tonnage (1000+/day-) from the lower levels of the mine would exceed the capacity of the existing hoisting system. A decision was made to sink a new vertical shaft at a point well in the south wall of the ore bodies where strong rocks and a minimum of faulting was expected and to purchase and install a new hoist capable of hoisting over 7000 feet. This new' shaft, designated as the No. 4 Shaft, was planned to reach 2000 feet below the 7100 level which was the deepest level at that time. The hoist would be in-stalled on the ,main 2000 Adit level which is used as an access and haulage level to the concentrator and surface plant in Burke.

Jan 1, 1971

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By B. L. Gibbs

The mining industry is constantly in a state of flux -boom or bust; mine openings and closings. Part of the reason is the nature of ore deposits -they are there or they are not. Once they are mined, they are reclaimed and the move is on to the next deposit. Risks are usually high, and payoffs can be great or not so great. Many factors go into making a property payoff, and mining companies are continually searching for ways to remain profitable as long as possible. Computers and the people who can make them work are one of the ways available to improve productivity and ensure this happens. Computers have been used in the mining industry for the last 30 years (and more in a few cases). During the past 10 years, the explosion of micro-computing has changed how many mining companies do their work.

Jan 1, 1993

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By T. Marcher, C. Mathiesen, M. Allende, S. Bauer

"A unique pumped hydro storage facility using the ocean as a lower reservoir, combined with solar PV to create consistent, clean power will be presented: the Espejo de Tarapacá Project is comprised of a 300 MW seawater pumped storage hydroelectric plant using the Pacific Ocean as its lower reservoir and an existing natural concavity at the desert as its upper reservoir. The plant site is located in Chile’s northern coast 90 km south of Iquique. The site is characterized by a rocky shoreline and about 600 m of flat terrain moving inland, with an abundance of rock outcrops, after which there is a steep 700 m cliff. The power house and all waterways will be underground. The main focus is to present the rocks being expected in the underground works. As one of the actual most tectonically active regions of the world the seismic activity is particularly relevant and will be outlined in the presentation. INTRODUCTION Valhalla Energy is an independent Chilean-owned power development company. It focuses on the development, ownership and operation of renewable power projects. Valhalla was founded in 2011 with the goal of developing Chile’s natural renewable energy resources and strategically diversifies the country’s energy matrix away from an overdependence on imported fossil fuels. Valhalla began developing pumped storage hydro projects to provide scalable, clean, competitive, and reliable electricity by combining Chile’s superior solar resources with the country’s unique and extensive coastline suitable for storage.The capacity for renewable energy supply is driven by two distinct and unique natural characteristics found in northern Chile: (1) the abundant and reliable solar irradiation in the Atacama Desert and (2) a coastal site that benefits from a steep cliff and a natural concavity both within a relatively small land mass (see Figure 1). There are several potential sites in the northern part of the country that can be developed. The “Espejo de Tarapacá Project” is the first one to be built and subject of the present paper."

Jan 1, 2016

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach is a relatively new method to study the mechanical behavior of rock masses. Recently, an SRM approach was established to estimate pillar strength from laboratory scale to in-situ dimension using the two-dimensional Universal Distinct Element Code (UDEC). In this study, the developed methodology is applied to the S-Pillar database to estimate pillar strength and failure mechanisms as a function of width-to-height ratio of the pillars. First, stone mine rocks are categorized into three as low-, medium-, and high-strength according to their uniaxial compressive strength (UCS). Later, laboratory-scale intact rocks are scaled-up to the average in-situ pillar dimensions by explicitly considering the naturally existing joint sets. It is found that the strength of the pillars with low-UCS are overestimated when compared to pillars with high-UCS. This observation is attributed to the high joint density of the pillars with high-UCS. After obtaining in-situ pillar strength, the width-to-height ratios of the pillar models varied from 0.5 to 2.0 to gain a robust understanding of pillar mechanical behavior. Tensile failure is found to govern the pillar behavior with the width-to-height ratio of 0.5 while the combination of tensile failure in rib elements and shear failure in the core