Search Documents

By H. H. Murray

New and improved benefication techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques including particle size separation, high intensity magnetic separation, chemical leaching, flotation, and selective flocculation are described and results and applications are discussed. The blending of clay minerals with other minerals provide opportunites to make special ceramic materials such as cordierite and other minerals which have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1989

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

By M. R. Peterson

The U.S. Bureau of Mines (USBM) is investigating alternative methods to strip metal-loaded solvent extractants. Hydrolytic, precipitation, and hydrogen pressure stripping all recover metal or metal salts directly from the organic solvent extractant. Pure metals, metallic oxides, or metal salts can be formed, allowing direct production of value-added products. Aspects affecting commercial application are emphasized, including metal recovery from actual ore leach solutions, particle size control, organic modifier and diluent effects on stripping and metal recovery efficiencies, metal grade, seed addition, mixing intensity, recycling efficiency, and reactor plating. Metal separations from copper ore leach solutions and complex waste leach solutions were examined.

Jan 1, 1995

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By J. W. Gulyas

Settling a contract for process design involves a negotiation between the design engineers and the client. Clients wish to offload as much risk as possible by seeking various guarantees about the process performance. Design engineers respond with preconditions and qualifiers, believing that the risk must remain with those who stand to benefit. This paper presents the engineers? point of view on guarantee types and precedents, performance testing, damages that may be claimed, and remedies that can be provided with particular reference to the mining industry.

Jan 1, 2010

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By Nasri Munfah, Steffen Matthei, Vojtech Gall

"Conventional tunneling as defined by ITA WG19 is also known as the New Austrian Tunneling Method (NATM) or Sequential Excavation Method (SEM) was transformed in the US to deal with challenging tunneling conditions as an alternative to the more traditional tunneling methods. It is being used more often in urban areas, under difficult ground and ground water conditions, and with limited cover. Often the tunnel is of a large and non-uniform cross section in soft soils or weak rocks. The intent of using this tunneling method is to minimize impact on traffic and utilities and reduce disruption of everyday life of people and businesses. To meet these challenges, the industry developed technical approaches and implementation techniques and established sophisticated contractual relationships and collaboration in the field among various parties for successful implementation. This paper examines the development of conventional tunneling (NATM/SEM) in the US to deal with these challenges using recent examples such as Russia Wharf in Boston, Northern Boulevard Crossing, in New York, and Chinatown Station in San Francisco. INTRODUCTION / HISTORY Conventional tunneling or NATM/SEM is a concept that is based on the understanding of the behavior of the ground as it reacts to the creation of an underground opening. In its classic form the SEM/NATM attempts to mobilize the self-supporting capability of the ground to an optimum thus achieving economy in ground support. Initially formulated for application in rock tunneling in the early 1960’s, NATM has found application in soft ground in urban tunneling in the late 60’s and has since then enjoyed a broad, international utilization in both rural and urban settings. In the US the NATM/SEM tunneling method has been used successfully to address challenging tunneling conditions in urban areas. A large number of tunnels have been built around the world using a construction approach which was loosely termed NATM. During the years of discussions and the application of NATM a variety of terms have been used for the same construction approach. These terms were primarily aimed at describing the construction approach rather than the region of its reported origin."

Jan 1, 2016

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By K. Fair

Using an agitated column 203 mm (8") diameter by 1829 mm (72") tall with independent agitation units for the gas dispersion zone and the collection zones, respectively, permitted the independent evaluation of the attachment and the detachment mechanisms for the chalcopyrite/ silica system. Three particle size fractions were used in this study, i.e. coarse (+75 µ m), intermediate (-75 µ m + 10 µ m) and fines (-10 µ m). The optimum selection of the two agitation zones for the three particle size fractions were determined as a function of grade, recovery, residence time and air superficial gas velocity.

Jan 1, 1990