Search Documents

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By Nicole R. Henderson

Many mining engineering graduates enter the mining industry lacking training in mine emergency management. As a result, mining universities in the United Sates and other countries are beginning to form volunteer student mine rescue teams to train mining engineering students in handling mine emergency situations and give them hands-on experience managing potential emergency scenarios underground. In the early 1980s, the Missouri University of Science and Technology developed the first collegiate mine rescue team in the United States. For approximately 30 years, it was the only successful collegiate team until the Colorado School of Mines (CSM) started its program in 2009. Currently, there are at least five collegiate teams in the United States and one in Canada. At the Freiberg University of Mining and Technology in Germany, the goal is to adapt the Colorado School of Mines Mine Rescue Program to develop a collegiate team of its own. Currently, mining engineering students cover the theoretical basics of mine rescue in an occupational health and safety lecture and take a basic, one-day mine rescue training course at the Central Mine Rescue Station in Leipzig. The course covers the basic mine rescue topics and gives students the opportunity to experience working in elevated heat and smoke conditions while wearing breathing apparatus. This training gives students a small insight into the importance of mine rescue and mine emergency management. Collegiate mine rescue teaches students the importance of mine rescue and mine safety by giving them hands-on learning experiences before entering the mining industry.

Feb 1, 2014

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Adam Saylor, Travis A. Shoemaker, Steve Miller

Lidar scanning has become an increasingly popular tool for documenting underground excavations; however, high costs of traditional mechanical electrical lidar hardware, software, and training have limited the frequency at which lidar scans can be performed. Additionally, traditional scanning can be time consuming because multiple scan positions are necessary. With Apple’s incorporation of low-cost mobile solidstate lidar on select smartphones and tablets, lidar is becoming more tractable for everyday construction documentation similar to construction photo collection with smartphones. Here, we describe benefits of mobile solid-state lidar and describe several practical applications for use in underground construction, such as documenting the working face, over-blast, and geologic features of tunnels.

Jun 13, 2023

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By M. C. Roberts

As nations advance through various stages of economic development, the patterns of demand for minerals change. For example, as a nation develops from a subsistence economy through industrialization and into a service based economy, the use of minerals is at first low, then grows rapidly, and finally stabilizes. The past trends in the use of agricultural minerals by the currently advanced nations provide a pattern that the world as a whole may follow as it progresses through the stages of economic development. Future needs for agricultural minerals are estimated using this approach.

Jan 1, 2001

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By M. Deutsch, E. González, M. Williams

"There is uncertainty in ultimate pit limits due to geologic variation and unpredictable economic landscapes. In this work we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis is used to model the effects of geologic and economic variation on ultimate pit limits and overall project economics. This analysis is made possible by a new, highly efficient pit optimization implementation which can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement, and to mitigate the possibility of incurring substantial costs relocating critical mine facilities. INTRODUCTION The mining industry is increasingly concerned with the effects of risk and uncertainty. Uncertain prices, unpredictable global markets, and unknown foreign exchange rates can alter the economic viability of a mining project in substantial ways. This economic uncertainty is compounded by geologic uncertainty. The extent and quality of any given deposit cannot be fully measured and is not known before consequential decisions must be made. These two sources of uncertainty are responsible for the majority of deviation between what happens during operation and what was initially planned. Understanding and explicitly quantifying this uncertainty will lead to better decision making and allow mining engineers and investors to be aware of what may occur. It is unrealistic to believe that one model, estimated from sparse measurements, is enough to capture both geologic and economic uncertainty and allow for optimal decisions. The entire breadth of uncertainty should be considered, as both upside and downside risks have large impacts on the investment potential and operational efficiency of mining projects. The workflow presented here uses Monte Carlo simulation and parametric analysis together to explicitly analyze the breadth of geologic and economic uncertainty as it applies to ultimate pit calculation and long range mine planning."

Jan 1, 2015

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo, Noelia Munoz-Garcia, Michèle Heitz

Sulfide tailings from past and present mining activities are important hosts of critical elements and precious metals. This review paper presented a literature survey on the recovery practices of some critical minerals containing Te from sulfide tailings with a special focus on the physical beneficiation and hydrometallurgical separation methods. Finally, a conceptual framework and possible processing flowsheets were proposed. The findings of this review will be useful for the researchers in the field of geochemistry, mineral processing, and metallurgy to evaluate the separation processes for reprocessing of mine tailings for the recovery of critical minerals.

Feb 1, 2024

By W. B. Hayes

The origin of the titanium pigment and metal? industries began with the discovery of the element titanium in 1791 by an Anglican clergyman named William Gregor. The titanium was discovered in magnetic black sands found in the beaches near Cornwall. England. The name titanium was established by the German chemist who discovered the mineral rutile in Hungary. Rutile is the oxide of the element titanium, which he called titan alluding to the mythological titans, giants of ancient Greece. The commercialization of titanium minerals began probably in 1916 with the production of titanium tetrachloride which was to be used in tracer bullets, flares and smoke screens during World War 1. In the 1920's composite pigments based on TiO2 barium sulfate and calcium sulfate were produced, followed by the introduction of the sulfate process anatase TiO2 crystal in the 1930s. The U.S. Bureau of Mines in 1938 began investigating titanium metal technology and promoted the development of the Kroll process. which is the magnesium metal reduction of titanium tetrachloride to produce titanium metal sponge.

Jan 1, 1989

By Ehsan Alavi, Sanjeer Yogendran, Savreet Singh

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel Project in Toronto extends approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. This project includes the installation of five intake shafts connected by 10.5 km of 6.3 m internal diameter tunnel and eleven drop shafts and vent shafts, connected to the tunnel by a series of adits. During the excavation of one of five intake shafts (20 m in diameter and 52 m deep), significant volumes of free phase oil and hydrocarbons were encountered. Due to the heavy inflows of the contaminants, excavation was stopped at the transition depth. The initial support of excavation needed to be redesigned, shaft had to be backfilled with CDF and installation of deeper secant piles are in progress to cut off contaminants. This paper outlines the initial plan for excavation as well as the design changes to the plan. The current status of the shaft excavation and lessons learned will be discussed.

Jun 13, 2021

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.