Search Documents

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By A. C. Smith

Although it is only utilized in a few U.S. longwall mines, a bleederless ventilation system can be an effective spontaneous combustion control method in mines with a demonstrated history of spontaneous combustion. In order to provide insights for the optimization of bleederless ventilation systems for U. S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas with a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical ventilation data for a longwall mine was used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of nitrogen injection to prevent spontaneous heating in the gob was also examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By R. G. Reddy

Viscosities of Feo-SiO2 slags were calculated using the previously developed structural based model. An expression was derived using hole theory and the atomic pair model to relate the NO0 and temperature to the viscosity. The deduced equation n=4.9x10-9 T1/2 NO0 exp (E/RT) poise was successfully applied to predict the viscosity of FeO-SiO2 slags in the composition range of 0.1 < XSiO2 < 1 for several temperatures. The calculated data agrees well with the experimental viscosity data.

Jan 1, 1991

By Giovanni Osellame, Jean Habimana

"The Montreal Metro Blue Line Extension Project is part of a metropolitan Program that was launched in 2009 by the Transportation Ministry of Quebec to add additional extensions to existing metro lines in the cities of Montreal, Longueil and Laval with the intention to meet current demand and future growth within the Montreal agglomeration. Specifically the Blue Line Extension Project will add five underground stations to the East of the Montreal. The paper addresses the preparation and the implementation of a three-step geotechnical and geo-environmental investigation program and preliminary design considerations such as the selection of a preferred horizontal and vertical alignment, the selection of construction methods based on previous local experience and current industry trends, as well as preliminary sizing of underground infrastructures. PROJECT BACKGROUND An agreement between the three mayors of the Montreal Metropolitan City agglomeration, namely, Montreal, Longueil and Laval prompted the Government of the Province of Quebec to create a project office to oversee the studies of extending the existing metro network. The last extension of the existing metro network was completed in 2008 with the Laval extension, which consisted of adding three stations from the existing Orange line. The current extension Program consists of three different extensions, namely extending the Orange Line to Laval and finishing the loop, extending the Blue Line to the East of Montreal by adding five stations, and adding five stations on the Southshore of the St-Lawrence River for the Yellow Line extension. The extension program also requires the construction of an underground storage and maintenance garage located to the north-west of the existing Cote-Vertu station on the Orange line. Figure 1 shows the overall extension program with the existing network."

Jan 1, 2016

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By M. Xing, S. Usman, K. Awuah-Offei

"While mines generally focus on achieving operational efficiency, creating shared value for all stakeholders is also a management goal. This includes taking a holistic view of their supply chains and increasing local participation. This paper examines the role of supply chain management in mine management; in particular the effect of a strong local supply chain on regional economic impacts. Using input-output analysis, the impact of a local supply chain on a mining sector’s regional economic impact is examined by increasing local sourcing (increasing local purchase percentage -- LPP) for 10 key commodities. An approach, based on multipliers and excess local capacity is used to identify key commodities. The impacts examined are sales, employment, labor income, and value added. The work is illustrated with stone mining and quarrying in Missouri. Ten percent increases in LPP of the key commodities, in this example, result in $4.1 million additional impact on the Missouri economy. This work can provide insight on how to better create shared value for all stakeholders. INTRODUCTION Little research has been published on improving mine supply chain management (SCM) to enhance regional economic impacts. Although some extensive academic research has explored the importance of an industries’ supply chain, not much is known about how a locally-based supply chain increases shared value in the resource sector. Across industries, traditional SCM is getting more and more complex. This is true of the mining sector as well. However, this increased sophistication is not directed towards increasing shared value for all stakeholders, particularly, the local communities. Further research is required to develop new SCM strategies that enhance local participation. One major point of difference between this work and traditional supply chain management is the inclusion of stakeholders’ shared value as a goal in SCM. Creating shared value has become a business goal in recent years (Porter and Kramer, 2011). The authors use input-output analysis (Leeuw, 2012) to evaluate the regional economic impacts of supply chain decisions, which is not part of traditional SCM. Although input-output analysis has been applied to SCM for decades, most of the research uses input-output analysis as a tool to advance an industries’ own operational efficiency (Accenture, 2014)."

Jan 1, 2015

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By William Wargo

The basic reason for lining underground cavities is to keep the cavity open during its useful life by providing adequately for the support of the surrounding rock and for the necessary degree of water tightness. This covers the entire field of support methods from the simpliest timber support to reinforced concrete in all its variations as applied to tunnels, galleries or shafts. The problem involved in the design of more efficient and economical lining systems for even bigger cavities has been magnified by increased speed of advance made possible by better blasting tecniques, improved tunneling machines and more efficient material handling. Tunnel lining today requires a disproportionate amount of time and money compared to other operations mostly due to the manuel labor involved in its installation. One solution to this problem is the developement of an entirely new concept in tunnel lining designed notoonly to overcome this bottleneck but also to open up the field for further increases in speed of advance. This new lining system acts first as a fast protective armour then becomes the concrete metal form and ends up as reinforcement sheet inside the concrete lining. This system developed and manufactured by Bernold A. G. of Switzerland since October 1968 has been installed in 25 applications in Europe under all ground conditions from stable rock to unconsolidated ground.

Jan 1, 1970

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources&apos; South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50&apos;s. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

The impact generated by old abandoned mines in Peru have produced mining environmental liabilities, which can generate an impact on the environment. In the search for long-term sustainable solutions, Phytoremediation is presented as an interesting alternative, since it allows the use of Peruvian native plant species for the accumulation of heavy metals. In this paper, we present the results of native high Andean species: Stipa Ichu and Cortaderia Nitida. The final metal concentration in the aerial parts and in the roots of each plant show that Stipa Ichu is more efficient to recover Fe, reaching almost 278 times its initial value. In the same way, this plant is efficient to remove Zn, Cu and Cd, reaching maximum values of 64, 39 and 12 times its initial concentration respectively. Cortaderia Nitida turned out to be more efficient to recover Fe, Zn, Cu and Cr, with highest recovery of 250, 117, 39 and 13 times its initial value respectively. Finally, based on translocation factor, Stipa Ichu has better capacities of hyperaccumulation of Fe, Cu, Zn, Pb and Cr. Cortaderia Nitida only shows hyperaccumulation of Cr.

Mar 2, 2022

By Gunjan R. Bhattarai, Kumar Bhattarai

Recently, there has been an enormous increase of interest in artificial intelligence (AI), machine learning (ML), and their applications by researchers, government agencies, and the underground construction industry. Ultimately, these tools have the potential to automate the design and construction processes and boost productivity, safety, quality, and operational stability. This paper presents ongoing research and applications of artificial neural networks (ANNs), robotics, and 3D technologies in ground characterization, tunnel ground support prediction, risk projection and reduction, and productivity enhancement in TBM operations. The paper further investigates potential uses of AI, robotics, and 3D technologies in the underground construction industry

Dec 1, 2022

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011