Search Documents

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

By K. Deaton

"INTRODUCTION A packaged cooling system is being developed for refuge alternatives (RAs) that meets MSHA qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed Refuge Alternatives (RAs) to be maintained by keeping the apparent temperature inside the RA from exceeding 95°F. Research investigations sponsored by NIOSH have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 95°F limit established in 30 CFR 7.504. Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 81°F mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines. The RAECS will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96 hour refuge period.This paper describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 95° limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature – approximately 60°F. The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 85°F. Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described."

Jan 1, 2017

By Jameel Menashi

A process has been developed for recovering the refractory metal values contained in mixed secondary source materials such as contaminated grinding wastes, oxides and sludges. The wastes are calcined with sodium carbonate in air to convert the refractory metals to water soluble Na2CrO4, Na3V04, Na2Mo04 and Na2W04. The base metals, Fe, Ni, Co and Cu, are converted to water insoluble oxides. An aqueous leach of the calcine effectively separates the refractory metals from the insoluble base metals. Co, Ni and Cu can be recovered from the oxidic residue by conventional processing methods. The leach solution is purified and then treated to recover the refractory metals as Cr203, NH4VO3, (NH4)6Mo7024?4H2O and H2WO4. The purity of the products is sufficient for their use in many metallurgical applications. The Na+ values in the leach solution are recovered as Na2CO3(or NaHC03) and are recycled to the calcination step. It is shown that the process can accommodate a wide range of feed compositions and generates a minimum of aqueous effluents.

Jan 1, 1984

By J. D. McKay

Continuous column flotation parameter testing, to improve operating methodologies, using coarse bubbles on fluorite ore from Nevada, revealed that retention time is the predominant factor affecting column flotation fluorite recoveries. Column height and feed injection location affected fluorite grades and recoveries because they affected particle retention times in the collection and cleaning zones. Other parameters tested, including froth depth, wash water addition, and axial mixing, showed varying results. Four defined zones within the column were found to have characteristic rates of upgrading per vertical foot. Fluorite-gangue separation was more efficient in a column than in a conventional cell at all particle sizes.

Jan 1, 1987

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By Louis A. Sandbak

Drift excavation by boom-type roadheaders in the San Manuel and Kalamazoo sulfide copper ore bodies has been successfully demonstrated. Geomechanical rock classification in conjunction with detailed geologic mapping has been necessary to assess roadheader performance, and to predict advance rates in the varied rock classes in the San Manuel block caving mine. Rapid excavation and less fractured ground are obvious advantages of roadheader drift excavation over conventional drill and blast techniques. The geomechanical system of Engineers International (1984) can be an effective roadheader performance and ground support tool.

Jan 1, 1985

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By Ken Mathers, Tom Conley, Jim Rozek

The Melbourne City Link Tunnels have been constructed through a BOOT process, the largest undertaking in Australia to date. Tolling commenced on the 1.6 kilometer Domain tunnel in April 2000, and the 3.4 kilometer Burnley tunnel December 2000. The project was delivered by design construct contracting and under ISO 9000. There were a number of major challenges in completing the tunnels, including much higher than expected groundwater infiltration, hydrostatic pressures greater than 6 bar, and unique design and construction applications required to prepare the tunnels for service. This paper covers the end play and final delivery of the tunnels.

Jan 1, 2001

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997

By Anna Sieminska-Lewandowska, Monika Mitew-Czajewska

"The construction of 6.3 km long central part of 2nd metro line in Warsaw was completed in September 2014 (7 stations - out of which three 25m deep stations - built using cut and cover method; two single-track tunnels constructed using four EPB TBMs as well as a short NATM section with soil freezing below the existing road tunnel). Central section of the 2nd metro line was opened to public after verification and testing in March 2015. Design and build tender for the extension of this line in East (three stations) and West direction (three stations) was announced with total length of running tunnels – approx. 5 km. Detailed description of a very complex geotechnical context, different construction methods, challenges encountered and solved during construction and finally lessons learnt on this interesting project are presented in the paper. DESCRITPTION OF THE PROJECT Introduction The very first concept plan of the metro system in Warsaw was designed several years after regaining independence by Poland in 1918. In 1929, following the geotechnical survey, design works begun, but the economic crisis of the 1930s stopped it. After a few years of break, in 1938 a coherent concept of the metro network was proposed to be implemented in phases over the next 35 years. In total, construction of 46 kilometers of metro, including 31 km of tunnels and 15 km on surface, was planned. Unfortunately, World War 2 made the implementation of those plans impossible. In the post-war period several metro designs were elaborated, but none except one was scheduled for implementation. Construction of the 1st, 23.1 km long, North-South line commenced in 1983 and finished in 2008 (Sieminska-Lewandowska et all. 2009). Nowadays, Warsaw covers the area of 517 km2 and, according to year 2014 statistical data, the city has much more than 1.7 million inhabitants. Only one operating metro line is not sufficient for such a populated city. Up-to-date metro plan, shown on Figure 1, includes also 30.5 km long 2nd metro line. It’s route is divided into four sections: Western Section with the length of approx. 9.2 km and 9 stations, Central Section with the length of 6.3 km and 7 stations, North-East Section with the length of 7.7 km and 6 stations, South-East Section with the length of 7.1 km and 6 stations. The construction of the central part of the 2nd metro line in Warsaw was completed in September 2014 and its operation started in March 2015. The paper focuses on challenges encountered and solved and lessons learnt during construction of the central part of the 2nd metro line in Warsaw."

Jan 1, 2016

By William Hustrulid

INTRODUCTION The Idarado mine lies high in the San Juan Moun¬tains on the divide between the Uncompahgre and San Miguel Rivers and consists of a consolidation of a number of old and prominent mining properties through which course some famous and very produc¬tive veins. Among the better known are the Smuggler, Tomboy, Montana-Argentine, Black Bear, Liberty Bell, Virginius, Flat, Barstow, and Japan, as well as many others. Most of these veins have been extensively mined over the past century and in the last three decades the Montana-Argentine and Black Bear veins have been the backbone of the Idarado mine; therefore, the descrip¬tion of the veins is limited to them. Access to the mine is through either the Treasury tunnel, whose portal is below Red Mountain Pass on US Highway 550 at an elevation of 3244 m (10,643 ft), or the Mill Level tunnel entrance 3.2 km (2 miles) east of Telluride, CO, at an elevation of 2761 m (9060 ft). The Treasury tunnel intersects the Black Bear vein 2643 m (8670 ft) from the portal and the Mill Level tunnel intersects the Argentine vein 2179 m (7150 ft) from the portal. Mining is by shrinkage stoping from slusher sublevels. The size of the scope blocks varies somewhat, but the standard size is 67 to 76 m (220 to 250 ft) long and 61 to 76 m (200 to 250 ft) high. The mine ranks either first or second in Colorado in yearly production of gold, silver, copper, lead, and zinc. It is 9.6 km (6 miles) from the Red Mountain plant to the Pandora plant, via interconnecting drifts and raises. There are engineering offices at both plants as a matter of convenience. The Red Mountain plant in¬cludes the company general offices, warehouse, carpen¬ter and machine shops, and mine change room. The Pandora plant consists of the mill and assay office, ma¬chine shops, and mine change room. The flotation mill has a capacity of 1632 t/d (1800 stpd), making a bul¬lion product and separate concentrates of lead, copper, and zinc. HISTORY OF THE MINE The Montana-Argentine vein was first extensively worked by the Tomboy Gold Mines Co., Ltd., a British concern. This company mined the stoped areas above the Ophir level between 1910 and the late 1920s and most of the stoped areas above the 2100 level between 1900 and the late 1920s. Gold was the principal ore metal mined. The area between the Revenue and Ophir levels was mined chiefly by the Revenue Mines Co. between 1900 and 1910. The ore was worked from the Revenue tun¬nel, which portals in Canyon Creek. Gold and silver were the chief metals recovered. The stopes between the 1700 and Revenue levels, as well as some higher stopes, were mined by Telluride Mines Inc. during the 1940s. The Mill Level tunnel was driven by that company from 1945 to 1948. Lead and zinc then became economically more important than the precious metals. In 1953, Idarado purchased Telluride Mines, which merged with the parent company in 1956. The Black Bear vein was first extensively worked by the Black Bear Mining Co. in the 1900s and by the Colorado Superior Mining Co. from about 1914 until snowslides at the mine camp [altitude 3750 m (12,300 ft)] terminated the company's operations in 1924. Leasers operated at intervals until 1934. The Treasury tunnel, formerly the Hammond tunnel, had been started before 1900 and reached the 1646-m (5400-ft) mark early in the 1900s, at which time activity lagged until the late 1930s. In the early 1940s, Idarado extended the Treasury tunnel from its heading at 1646 m (5400 ft) to the Black Bear vein and established a raise connec¬tion with the 600 level, the lowest level in the old mine. Since completion of initial work in the mid-1940s, systematic development of the mine, both in the driv¬ing of new headings and the utilization of older open¬ings, has resulted in the present extensive network of workings. GEOLOGY Introduction The oldest rocks of the area are the Precambrian metamorphic rocks, the Uncompahgre formation which are massive quartzites, some phyllites and slates, and dolomitic or limestone beds. West-dipping Paleozoic and Mesozoic strata lie on the Uncompahgre formation. These units are separated by a major angular uncomformity from overlying, essentially horizontal, Tertiary formations that include the basal Telluride conglomerate and several thousand feet of overlying volcanic rock. Intrusive rocks, mostly Tertiary in age, are common in the area, and are in the form of dikes, stocks, and sills. Dikes are very closely associated with some of the ore veins (Mayer). Description of Veins The Black Bear and Argentine veins range from 0.6 to 7.6 m (2 to 25 ft) in width, but in most places are 1.5 to 2 m (5 to 7 ft) wide. They vary in character from a well-defined tabular structure between sharp "frozen" walls, or gouge seams, to an irregular zone of quartz and quartz-sulfide stringers. Many gouge seams within the veins make the veins blocky and loose. Common gangue minerals in the veins include quartz, pyrite, rhodonite, chlorite, sericite, clay minerals, epidote, calcite, adularia, rhodocrosite, fluorite, and specularite. Quartz constitutes 60 to 70% of the veins and varies widely in character, ranging in color from clear through white, gray, and green, to amethyst. Chlorite, sericite, the clay minerals, and fine-grained quartz are common alteration products of the vein walls and of wall rock fragments in the veins. Epidote is an altera¬tion of the dike or, less commonly, of tuff-breccia. Calcite, adularia, fluorite, and rhodocrosite, which are wide¬

Jan 1, 1982

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By M. G. Karfakis

Grouting has been used in underground mining for more than twenty years. Chemical grouting is often used as a remedial measure when the implemented ground control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. Utilization of the polyurethane grout currently being used is restricted by its limited range of physical and mechanical properties that restrict its utilization. To overcome some of the drawbacks of polyurethane, research has been conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as StrataGrip, provides a number of features, including variable gel times and much reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted. Assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research have defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1997

By Robert J. Clarke

Reflections on over ten years experience handling bituminous coal from railroad cars to ground storage and lake vessels. The arrangement of the facilities is described but the basic theme of the discussion is the experience gained and lessons learned from facility operation. The Great Lakes provide the maritime environment for the economical transport of vast quantities of raw materials from their source in the Upper Lakes (the Mesabi Range, for instance) to Lower Lake Ports. Lake Erie, because of its proximity to the steel centers , blossomed with the great ports that now line its southern shore - Toledo, Sandusky, Lorain, Cleveland, Huron, Ashtabula, Conneaut and Erie.

Jan 1, 1981

By George R. Stephans

The Climax Mine is a panel caving mine which has had a long history of incidents of severe ground control problems. The nature of the ore deposit, which lends itself to the caving meth- of of production, a1 so makes the mine susceptible to large scale stress concentrations which are referred to as ?weight? problems. These problems have increased with increased production and also with expansion to deeper mine levels. During the past twenty years the mine has had to learn to cope with these problems in order to remain in operation. A number of practical guidelines and useful techniques have emerged from these efforts. The purpose of this paper is to share a few of these ideas. The Mine is located near Leadville, Colorado on the continental divide at an elevation of 3450 meters. The ore body is a large low grade deposit of disseminated molybdenum sulfide. It measures about 1200 to 1600 meters in diameter and it had an original depth of about 660 mters. The Mine has been in operation since 1918 and the massive nature of the ore body together with its blocky, highly fractured condition made it natural for the caving system to have been adopted for production at an early date. Open pit mining was started in 1973. The total plant has a capacity of more than 50 thousand tons per day, and more than 400 million tons of reserves at an average grade of 0.310 percent molybdenum disulfide remain to be produced.

Jan 1, 1982

By M. J. Raffaldi, L. A. Sandbak, K. K. Dehn, S. N. Warren, J. B. Seymour

"Confidence in the design and stability of an undercut cemented rockfill (CRF) span requires a thorough understanding of its emplaced material properties. The unconfined compressive strength (UCS) of cast 6×12-inch QA/QC cylinders is typically used as an index test to track the performance of a backfill plant. However, these strengths need to be adjusted for oversize aggregate removal and sample size effects if used to estimate the emplaced UCS. UCS testing of 6×12, 12×24, and 18×36-inch cast CRF cylinders was used to quantify the relationship between readily available 6×12-inch QA/QC strength data and the emplaced UCS. Test results indicate that the UCS of 18×36-inch cylinders is roughly 40% of the 6×12-inch UCS for similarly compacted samples. Mine QA/QC data indicate that the UCS of CRF is highly dependent on the degree of compaction as measured by bulk density. Based on these results, knowledge of the emplaced CRF density compared to 6×12-inch QA/QC density is also necessary to estimate the emplaced UCS. The scale effect reported in this study is more pronounced, compared to current understanding of backfill properties discussed in the literature, and underscores the need for further site-specific testing. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SRMD), in cooperation with Barrick Gold Corporation, is conducting research with the goal of determining a relationship between 6-inch QA/QC cylinder strengths and the in-place strength of cemented rockfill (CRF). CRF cylinders with dimensions (diameter × length) of 6×12, 12×24, and 18×36 inches were cast onsite at the Turquoise Ridge Joint Venture (TRJV) and Cortez Hills Underground (CHUG) mines using CRF mixed at the mines’ respective batch plants. UCS tests were performed after 28 days of curing to estimate the size correction factor for each mine’s CRF. This paper presents an overview of the mix designs, sample collections, testing methods, test results, and an estimate of the UCS size correction factor for CRF at these mines. BACKGROUND Underhand cut and fill mining methods utilizing cemented backfill are common in underground metal mines in the United States. These methods are advantageous for controlling weak or highly stressed rock mass conditions by creating an engineered material that can be placed in openings, forming a beam that provides a safe, stable back for the next undercut. Increased use of underhand methods in the last 30 years has greatly improved safety in many cut-and-fill mines. However, with the continual push for more efficient and cost effective mining, there is a need to thoroughly understand the geotechnical properties of cemented backfill to assist in designing safe, stable openings while optimizing costs and production schedules."

Jan 1, 2018

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986