Search Documents

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By Edward J. Sterne

Several shale-hosted Pb-Zn-Ag deposits have been discovered in the northwestern Brooks Range, Alaska. Best known among these are the Red Dog, Drenchwater Creek, Lik, Ferric Creek, Hot Dog Creek, and Competition Creek deposits. They occur in a tectonically disturbed sequence of of Mississippian to Triassic shales, argillites, and cherts, and most are spatially associated with volcanic rocks. The sulfides are hosted in shales as disseminations, banded layers, massive lenses, and crosscutting veins. Detailed geologic descriptions of sulfide prospects in the Brooks Range were given by Tailleur (1970), Nokleberg and Winkler (1978), and Plahuta and Robinson (1979). Lange et al. (1980) discussed the formation of the deposits, the nature of the mineralizing solutions, and the temperature of formation on the basis of sulfur isotope studies. More recently, Harrover et al. (1982) detected a correlation between sulfide mineralization and high-temperature formation of charts associated with the sulfides by oxygen Isotope and chert crystallite size determinations.

Jan 1, 2013

By R. Vergunst, E. A. Devuyst, G. Robbins

By the middle of 1989 Inco will have applied its patented cyanide removal technology to seventeen commercial operations. Removal of cyanide from CIL slurry tailings is applied at Equity Silver and Inco's new 1.200 mtpd mill at Inco/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3.600 mtpd), Canamax's Ketza River (360 mtpd) and Westmin's Silbak Premier (2000 tpd) operations. Repulped tailings from Merrill-Crowe flowsheets are treated at Total Erikson's Mount Skukum (300 mtpd) and Skyline's Johnny Mountain (200 mtpd) mills and barren bleed at Inco/Queenston's McBean mill (500 mtpd). Lynngold's MacLellan mill (1800 mtpd) and ERG (40.000 mtpd) treat pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating and two other plating shops in Ontario. Details regarding some of the above operations are given. Operating and capital cost estimates for various treatment options are discussed.

Jan 1, 1989

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By Eddy J. Jacques

When the automatic control of a ventilation process is considered, and supervising expert systems need to be designed, an important problem to address is: what will be the optimal set points of the regulators that should meet a certain number of independently formulated requirements, distributed over a ventilation network? The set of these requirements, expressed in terms of air flow quantities or differential pressures in certain airways, need not be consistent. Their number is not limited by the number of available regulators, nor by their nature, i.e. passive or active. Moreover, they may be subject to upper or lower limit values. The method described here addresses this problem and tries to provide a tool that should allow to calculate the set points of all the regulators as a global and optimal solution with respect to this set of distributed requirements. The pure mathematical developments in this paper are kept as short as possible in order to allow more room for the description of a relevant example.

Jan 1, 1991

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By Tomek Ulatowski

This article discusses four principal areas relevant to financing direct reduction facilities: (1) Lenders' differing requirements with respect to projected cash flows; (2) The impact of leveraging on project viability; (3) The importance of appropriate debt structure; (4) The significance of accurate and complete capital cost estimates. The overall findings emphasize the inseparable connection between the project economics and its financeability, and particularly how direcly intertwined they both are in the project planning.

Jan 1, 1978

By Ben DiFiore, Richard DePew, Nate Long, Adrian Naranjo-Castillo, Chris Petta, Robert Auber

The Walworth Run stream was brick-culverted in the 1800s, converting it to a 16-ft diameter sewer. This Cuyahoga River tributary contributed to the infamous burning river that became the catalyst for USA’s environmental movement. The NEORSD has been working hard to reduce CSOs here, most recently by diverting Walworth Run’s 882 MGD of flow to the new Westerly Tunnel. This had to consider structure age/size, alluvial/glaciolacustrine deposits (requiring several ground support systems, groundwater control), and maintenance of massive flows. This paper examines challenges identified during design that supported the contractor in development of a risk-mitigating plan, culminating to successful implementation.

Dec 1, 2022

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By D. Berberick

Hecla?s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d?Alene mining district of northern Idaho. Main access into, and production from, the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk by J.S. Redpath to an original depth of 1,890 m (6,200 ft) in the early 1980s. The shaft is divided into four compartments (Fig. 1), with sets made of 225 mm x 175 mm (9 in. x 7 in.) hollow structural section (HSS) steel buntons and 150-mm x 150-mm (6-in. x 6-in.) HSS dividers spaced every 4.5 m (15 ft) down the length of the shaft. Two skip compartments on the east side of the shaft are equipped with 125-mm x 150-mm (5-in. x 6-in.) HSS steel guides and 9-t (10-st) skips with three deck trailer cages for men and materials. The west side of the shaft is divided into a manway, and a fourth compartment that was originally designed for a service cage. Shaft services consist of a 250-mm (10-in.) a compressed air line and 150-mm (6-in.) sandfill line along the south side of the shaft, and 250-mm (10-in.) discharge (gray) water and 150 mm (6 in.) fresh water lines on the north wall. The mine?s primary 13.8 kV power lines, as well as communication lines are located on the west wall of the shaft. The production hoist is a 3.7-m (12-ft) diameter, double drum, double clutch, 2,238 kW (3,000 hp), direct current unit equipped, at the time, with thyristor drives. The 30-year-old drives would prove to be problematic during the rehabilitation project, leading to an upgrade to modern ABB drives later in the project, after the shaft rehabilitation was complete. The shaft had been subjected to the typical wear and tear of 30 years of operation, including intermittent sandfill and muck spills, and, in the lower areas, some corrosion. During those 30 years, the west compartment, originally designed for the service cage, could only be accessed from a work deck on top of the skips or from the manway.

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By G. Knight

It is shown that the dust exposure of all underground workers varies greatly from day to day even though each man did the same job in the same working place each day. The variability follows a logarithmic normal distribution with a geometric standard deviation of about 1.6 for the three dust assessments; total respirable dust, respirable combustible dust and respirable quartz dust in both mines studied. The variability was homogeneous for all men and most jobs. The differences between men doing the same job was found not to be significant and it is suggested that the dust sampling program should determine the average for each job and use this as the best estimate of the exposure for each man.

Jan 1, 1980

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By Elena Chiriotti, Federico Valdemarin, Jan Cenek

"SUMMARY The “28 May Station” is the only transfer station between the existing Green and Red metro lines in Baku. As part of the huge development strategy of the metro network, the complete separation of the existing underground lines has been planned at this location, in order to simplify the operation of the future metro system. The extreme challenge of the project is represented by the need of achieve the separation of such lines over a breakdown of the operation of just five weeks. The lack of direct access from the surface, a complex geology with artesian water layers, a congested underground space and sensible buildings represent additional constraints. The chosen design solution consists in creating a complex steel pipe jacking frame around the operating tunnels and then excavating under such frame two large caverns where the separation of the existing lines and the construction of the new metro tunnels will be achieved. Soil treatments have been conceived to mitigate the geotechnical risks and to reduce possible impacts on the existing structures. The paper illustrate the challenges of this extraordinary project, one of the most complex underground structures under study, the design solutions and the risk management approach used to manage the complexity and to design the mitigations measures. INTRODUCTION The metro network in the capital of Azerbaijan is rapidly growing together with its metropolitan area. The beginnings of the existing metro system started in Baku in 1967 in Soviet times. To date, only two lines (Green and Red) are in operation with a total length of 34 km, including 23 stations. The future network will be much wider: besides the construction of three completely new lines and the extension of two existing lines, the whole metro project includes the development and modernization of the existing metro sections. A consortium formed by Systra (leader), Mott MacDonald (Praha) and Saman (Korea) awarded the contract for the preliminary and detailed design of infrastructures for the extension of Baku Metro Network. This extension consists in 83 km of new lines and extension of existing lines. As part of this modernization project, the connection of the Green Line at the 28 May / Cefer Cabbarli Stations, focus of this paper, represent also it’s ""Achilles' heel"" given that the already very congested system have only one transfer station."

Jan 1, 2016

By John W. Antalovich

Normally I would like to begin a talk on photogrammetry by defining the word. However modern technology has changed the science so radically that it bears little resemblance to its original definition. Photogrammetry as defined is a science of taking accurate measurements from photography. Today's photogrammetrist, in addition to working with photography, finds himself working with magnetometers, infrared scanners, radiometers, holo¬graphy, lasers, side-looking radar, digital interfaces, computers and countless other modern space age concepts. The modern photogrammetrist is a pilot, photographer, lab technician, mathematician, geologist, programmer, engineer, physicist, and cartographer. His modern instrumentation and many spheres of activity all have a role in the environmental sciences. For example, the magne¬tometer which measures the earth's magnetic fields is used to locate the earth's ore deposits. The infrared scanner captures the heat emitted from the earth to detect ground waters and thermal pollutions. To elaborate on each of his many endeavors would take volumes rather than this short paper. I have elected therefore to discuss what I feel is his most important role in the environmental sciences - that of cartographer.

Jan 1, 1970

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970