Search Documents

By George Schmitt, Ted Dowey, Grant Millener, Sean McAndrew, Eric Jordan

The Rondout-West Branch Bypass Tunnel is being built to bypass a substantial leak in New York City’s primary water supply tunnel. The 13,500 foot long tunnel travels 600 feet under the Hudson River through the same troubled geology and high pressure water inflows that the original tunnel did in the 1940s. A Robbins TBM traversed this geology and built gasketed segments. Nine thousand two hundred feet of 16 foot diameter interliner was installed and backfilled within the segments. Finally, reinforced cast in place lining was placed. This paper addresses the challenges and the multi-tasking approach the contractor utilized.

Jun 13, 2021

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992

By G. E. Jones, G. K. Hoffman

Two Sun Juan Basin studies were completed through the USGS National Coal Availability program. The study areas are in the northwest Bisti field (Fruitland Formation) and in the eastern Standing Rock field (Menefee Formation). In the Bisti and Standing Rock areas, the original coal resource5 are estimated at 4.66 and 3.1 7 Gt (5.14 and 3.49 billion st), respectively. The Bisti coal resources are greatly reduced by the Bisti-De-Nu- Zin wilderness area, which contains an estimated 1.13 Gt (1.25 billion st) of coal. Technological restrictions remove 32.5% from Standing Rock's original resource. Available resources are 60%. 2.79 Gt (3.07 billion st), of the Bisti original resource and 65%, 2.07 Gt (2.28 billion st), of the original Standing Rock resource.

Jan 1, 2002

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By Richard J. Leary

At the 1976 Annual Meeting of AIDE, Alan Merson reminded his audience that economic' success comes to those who understand things as they are, rather than as they have been or what ideology says they should be (1). He went on to say that, measured by this standard, the mining industry is in trouble. The mining firms had recognized long ago the importance of effective lobbying in Washington and the state capitals. But, he pointed out, those methods are nearly worthless anymore in coping with many land use problems because the critical decisions are likely to be made at the local level. There the tactics are far different as are the relations of the decisionmakers to the parties before then. Furthermore, in his estimation the trend is to leave land use regulation largely to the local level of government. All who are concerned for access to land for mineral development will be benefited by reading Professor Merson's paper lie is speaking effectively about the context of decisionmaking for specific cases, the shape of things in the here and now. There is, however, a longer-tern set of considerations that if pursued will be likely to foster the creation of public support for mining developments. At that sane meeting I spoke on two foundations of the long-term relationships: namely, the growth in requirements for minerals implied by projections of increasing consumption; and a rationale for fostering mineral exploration and development. I mentioned in passing the social decisionmaking process for public uses of land (2). This paper is intended as a complement. The growth of requirements for Minerals and the rationale for development based on the Entropy Law will be only mentioned. The main concern will be on the process of social decisionmaking in the context of access to land for mineral development.

Jan 1, 1976

By ANDREW HOBERT, Maoming Fan

Low-cost and environmentally friendly green froth flotation modifiers of plant origin, such as guar gum, carboxymethyl cellulose (CMC) and starch, have been used in the flotation of some sulfide and nonsulfide minerals. This paper discusses the fundamentals, current applications and potential new applications of guar gum, CMC and starch in minerals flotation. In this study, improved flotation performance was achieved using some green modifiers in flotation columns.

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. First, the talc sample was wet-ground in a stirred media mill for five different lengths of time (30, 60, 90, 120 and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35 and 50 µm), solid ratio (2.5, 5, 7.5 and 10 percent), and sonication time (60, 120 and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50 ), reduction ratio and specific energy consumption. Submicron particles prepared by ultrasonic treatment were highly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on the structural properties of talc particles were characterized by X-ray diffraction (XRD) analysis.

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By Nelson M. Solow

Raise boring of mine ventilation shafts in many cases offers a lower cost and higher speed method of construction in comparison to conventional shaft sinking. Where underground access is available for raise boring the potential savings indicate that raise boring should be considered as an alternative to other methods. Raise boring machines are currently in use which have the capability for reaming shafts up to twenty feet in diameter, depending on the strata and depth. These large capacity machines make it possible to consider raise bored shafts for moving large volumes of air. Although we will consider here only ventilation shafts, raise boring should also be considered for men and material shafts. When the mine planner has determined the volume of air required through a shaft at a particular location he is faced with the problem of selecting the shaft size. The principal factors in optimizing the shaft size are the construction costs for the shaft 'and the power cost to move the air through the shaft. The larger diameter the' shaft is the more it costs to construct, but for a given volume of air the power required (cost) becomes lower as the diameter increases. The construction cost is paid only once, when the shaft is constructed. The power costs, however, are paid throughout the life of the shaft. Methods of optimizing air shaft size found in the literature (References 1 and 2) amortize the construction cost and include it in the average annual cost of operating the airshaft. These methods derive a formula for the average annual cost vs. shaft size and de-rive the formula to compute the optimum size for a given air flow rate. It is, however, desirable to take into account tax considera-

Jan 1, 1977

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By E. G. Loesche

Grinding mills in which the comminution takes place between rollers and the surface of a disc, table or ring are generally known as roller type mills. The Loesche Mill, also known as the Disc Roll Mill, is a special type of roller mill in which the grinding surfaces consist of two rollers assembled over a horizontal disc or table which rotates at a relatively low speed. This design is particularly applicable to industry's present day demand for large capacity grinding mills.

Jan 1, 1964

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022