Search Documents

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

The removal of tritium from tritiated water (-0.5 µCiIL) was studied by metallothermic reduction using aluminum. The influence of the three variables namely the aluminum powder amount, the NaOH concentration and the reaction time has been studied on the tritium activity reduction. The experimental results and statistical analysis showed that more than 85% of tritium can be removed from the tritiated water. Further work on the tritium recovery as well as efforts to totally decontaminate water by incorporating a cryogenic concept is currently pursued.

Jan 1, 1998

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Drummond Earley III

The hydrology of in situ leach mining operations is being studied by the U.S. Bureau of Mines using a variety of techniques, and the Bureau has made significant advances in tracking and modeling the flow of leach solutions in rock formations. However, the influence that leach solution composition has on the hydrology of these systems is poorly understood, and geochemically-controlled changes in the hydrologic characteristic of ore deposits during in situ leach mining of porphyry-hosted, copper oxide ores have not been previously studied. The Cyprus Casa Grande in situ leach mining operation mines fracture-hosted and disseminated copper oxides (predominantly chrysocolla) hosted by granodiorite porphyry using a pattern of underground wells. The injection solution consists of sulfuric acid raffinate from a solvent extraction-electrowinning plant. Chemical analysis of representative injection and recovery solutions reveals that gangue cation concentrations in these solutions are high, and geochemical modeling shows that the solutions are saturated or nearly saturated with respect to gypsum, jarosite, and various amorphous oxides. Precipitation of these solids is evoked by calcium-exchange reactions, rising pH, and perhaps locally rising redox potential, as the leach solution reacts with the ore minerals, host rocks, and the atmosphere. Mass and volume balance calculations show that approximately 25 cm of precipitates are formed per gram of copper recovered at Cyprus Casa Grande. The results of geochemical modeling agree with petrologic examination of pre-and post-leach core samples from the leached horizon. Moreover, hydrochemical modeling and hydrologic field data suggests that chemical precipitation causes significant decreases in porosity and permeability during in situ leach mining of porphyry-hosted, copper oxide ore.

Jan 1, 1992

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Thomas H. Koenning, James R. Boulton

The coal mined by Cyprus at the Shoshone mine near Hanna, WY is highly susceptible to spontaneous combustion. Spontaneous heatings have occurred in the gob of several of the longwall panels and, in some cases, following roof falls. Prevention and detection methods have evolved over the years as more has been learned about the occurrences. Seal design and construction have progressed to reduce air leakage into the gob. Pressure balancing has been successful as a supplement to good workmanship in reducing leakage. Early heating detection has improved as knowledge has been gained. Prior methods of detection relied upon thermocouples detecting a temperature change. Later a gas chromatograph was used to analyze gob gas samples. Initially the products of combustion (POC) were relied upon for detection. Most recently, lack of oxygen depletion in the gob has been used as an early warning of problems. Examples are presented to illustrate the evolution of spontaneous combustion control at the Cyprus Shoshone coal mine. Methods have been developed which minimize the oxygen concentration in the gob and reduce the potential for spontaneous combustion.

Jan 1, 1997

By H. C. Seeber

When considering all the aspects of a viable mine plan, it is important to estimate the accurate cost of mine ventilation, which varies as a function of airway dimensions, fan selection and ventilation network. Optimization of the overall elements of ventilation design can lead to very significant cost savings when capital and operating cost savings are considered in combination. This paper will describe a methodology, whereby ventilation costs can be minimized by optimizing the ventilation aspects of mine design and fan selection, by providing a brief description on ventilation theory and the factors which affect ventilation operating and capital costs.

Jan 1, 2002

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By C. S. Simons

The aphorism that provided the title of this paper is probably a couple of hundred years old, but it still expresses a fundamental truth in the metals industry. This truth will be illustrated through a brief review of the major developments in the extractive metallurgy of the oxidized ores of nickel - the "laterite" ores. While the details to be discussed are for the most part specific to nickel, a close parallel with other commodities - particularly in recent years - will be apparent even to those whose interest in nickel itself is slight. Thus it is hoped that this paper will be stimulating, at the least, to anyone who is concerned with the implementation of process improvement, "Invention" in the present context means any change from "conventional" process technology that shows a reasonable chance of reducing costs, increasing revenues, or both, in the production of a commodity. This can be anything from a simple rearrangement of flowsheet steps to a completely different basis for processing. And the result may reduce costs by more efficient use of energy or labor or reagents; may increase revenues by better recovery of the primary product or by introducing the recovery of previously ignored by-products; may insure sales volume (and thereby cash flow) through higher product purity or an improved product form. "Necessity" is the perceived need to attain at least one of these classes of results. This perception of necessity, however, varies widely from management to management and from project to project.

Jan 1, 1983

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By A. S. Ibrado

Research investigations on the chemistry of the adsorption of gold cyanide on activated carbon have mostly reduced the role of activated carbon as the provider of the large surface area needed for adsorption. Most do not go beyond suggesting that oxygen functional groups on carbon play a key role in the adsorption process. Our research shows that the nature of the material, specifically its structure, is a crucial factor in the adsorption equation. To delineate the effect of adsorbent properties, gold cyanide was adsorbed on a series of carbonaceous adsorbents, including lignite, coals, anthracites, carbon blacks, graphite and activated carbon, which covers wide variations of composition, surface acid group content, and degree of graphitization. The results show that the adsorption of gold cyanide per unit area of adsorbent is not related to the amount of oxygen groups on the surface or even the total oxygen content of the material. However, they show very strong correlation with the degree of graphitization of the adsorbent, which indicates that the graphitic plates of activated carbon play the most important role. The findings suggest that majority of the adsorption occurs on the plate faces of the graphite crystallites of activated carbon.

Jan 1, 1992

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper outlines a cutting-edge probabilistic resource modeling workflow tailored to the Round Mountain epithermal gold deposit. The primary goal is to craft a robust and modern simulation process that enables the quantification and comprehension of anticipated discrepancies during mining reconciliation, offering a more precise gauge of expected gold quantities compared to conventional estimation models.

Dec 1, 2023

By R. Lawrence

Mineral property valuations to be used for Canadian securities regulatory purposes must comply with CIMVal1. The technical basis for a CIMVal report is the same as that required for a technical report that complies with NI 43-1012. NI 43-101 describes the content to be covered in a technical report, while also covering other requirements, one of which is that the report should be based on a property visit. CIMVal is based on five tenets that the valuator must follow: ? Materiality. ? Independence. ? Transparency. ? Competence. ? Reasonableness. Upon its adoption by CIM Council in 2003, it was hoped that the new CIMVal code would be adopted without change by the several Canadian regulators.

Jan 1, 2011