Search Documents

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By D. Erik Spiller

A commercialized dry gravity concentrator is operating on an alluvial gold deposit in the Boludo Mining District, State of Sonora, Mexico. The technology base of the process is the Rotary Air Concentrator (a dry circular air jig) that recovers gold from the desert sand resource. An overview of the Mexican operation and the dry concentration technology is presented. Application of the dry technology to pretreat­ment of heap leach feeds and other heavy minerals is a pos­sibility.

Jan 1, 2000

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By B. F. Dickerson

STRATEGIC METALS! Recently, this money accented cry has been heard in such diverse locales as Mining company boardrooms, Banker's offices, Stockbroker's quarters, Swindler's dens and Congressional committee rooms. (In some cases, these locales are one and the same). Is the strategic metals rush for real? Should it be? Our paper attempts to give a very generalized view of the subject for a few metals, points to a few potential, but generally overlooked sources of these metals, and offers conclusions based on our studies.

Jan 1, 1981

By J. David Lowell

The discovery of the Kalamazoo (Arizona) ore body was a comedy of errors and coincidences and luck -as most discoveries probably are. The story began in early 1965 when Quintana Petroleum decided to diversify from petroleum into minerals and decided to do this by the route of minerals exploration. Quintana Petroleum is owned by the Cullen family of Houston and has Geen successful over the years in discovering oilfields. In 1965, the president and general manager was Corbin J. Robertson, son-in-law of Harry Cullen, founder of the company and a famous Texas wildcatter. But, in 1965, Quintana's financial advisors suggested that the company go into several mineral commodities, including copper, with Tucson, AZ, as the jumping-off point for copper exploration, and with a geological consultant (me) as the point man. The stage was now set! (See Fig. 1, location map of the San Manuel District, Arizona.)

Jan 1, 1991

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By J. W. Mahar, E. J. Cording, F. L. Gau

INTRODUCTION The Washington, D.C. rapid transit system (METRO) when completed will consist of 98 miles of double track rail. Fifteen miles will be tunneled in rock and 12 large underground rock chambers will be constructed at station locations. The University of Illinois is under contract to Metro to provide observations and instrumentation services in the initial phase of construction. The work is coordinated through DeLeuw, Cather & Co., the General Engineering Consultant to Metro. The program is designed to monitor construction conditions as well as to provide information useful for the design of future rock tunnels and rock chambers in the Metro system. This paper presents the results of observations in the rock tunnels constructed to date. Most of the observations are in a 5000-ft-long, 30-ft-wide, double track tunnel in downtown Washington, D.C. Observations were also made in single track tunnels, shafts, enlargement areas, and pilot tunnels, and are being made in a large rock chamber 700 ft long, 76 ft wide, and constructed at shallow depth in a schistose gneiss. One of the major objectives of the observational program was to determine the orientation and character of joints and shear zones and to evaluate their effect on support requirements for various tunnel orientations and configurations. The consistency of geologic features throughout the Washington area has made the results of the initial study applicable to evaluation of support requirements on future tunnel contracts. The first section of this paper summarizes the geologic conditions in the tunnel and their effect on overbreak and rock movement.

Jan 1, 1997

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By Philip M. Rice, Paul Schmall, Peter W. Deming, Hugh S. Lacy

A groundwater cut-off is needed to provide a stable face of tunnels to be constructed by jacking precast rectangular tunnel segments beneath commuter rail tracks for the new I-90 extension in Boston, MA. Extensive obstructions are present within the path of the tunnels. This paper describes how the use of artificially frozen ground is being planned to provide a reliable groundwater cutoff and assure a stable tunnel face. Monitoring during freezing assures continuity of the cutoff. Laboratory testing of frozen soil samples aided the design of this frozen soil boundary. Logistics of installing vertical freeze pipes are described.

Jan 1, 1999

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By A. D. Davis, J. L. Sorensen, C. J. Webb

Environmental impacts from acidic mine drainage are growing national concerns that are particularly acute in the headwaters of the Rocky Mountain region. In the Black Hills of South Dakota, approximately one thousand mines are inactive or abandoned, most of them in the headwaters of major drainages. This paper examines the Bear Butte Creek basin, a heavily mineralized watershed with significant historical mining impacts and a surface gold mine permitted in 1997. The watershed loses its surface discharge to swallow holes in the karstic Madison Limestone. The integrity of the aquatic ecosystem was monitored with a suite of sitespecific bio-indicators. Stream surveys covered the entire reach of Bear Butte Creek from near its headwaters to the swallow holes in the Madison aquifer. Data from the stream surveys, water-quality sampling, and bio-indicator surveys clearly showed that water-quality impacts are limited mainly to Strawberry Creek and to the area of Bear Butte Creek near and downstream of the town of Galena.

Jan 1, 1999

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

By Douglas R. Cook

Exploration record In preparing this paper, a list of world class discoveries prepared in 1983 has been updated. In both surveys, the following criteria were used in the definition of world class discoveries: • deposits that are continuously operated and consistently return a profit even in periods of low metal prices; • deposits large enough to significantly affect a medium sized corporation's profits; and • these deposits should be in the lower one-third cost per unit of metal produced for all similar deposits. Only 70 discoveries in the last 40 years qualified as world class deposits using these criteria. Unfortunately, this restricted population was too low to develop meaningful trends. The numbers were therefore enlarged to include all significant discoveries. The principal feature of a significant discovery is that its size and grade would yield more than $500 million in revenue using average metal prices for the last five years. A significant deposit should also meet some of the standards for a world class deposit. A tabulation of these deposits are shown in Table 1. The number of discoveries increased to 166 from 70 using the revised classification. The relationship between the number of discoveries per year and their location by continents was prepared from these data. Figure 1 shows the number of discoveries per year for the nonCommunist world. It also shows estimated and actual nonCommunist world exploration expenditures per year and the commodity price index. These data show that modern exploration started in the late 1940s, with the tempo picking up rapidly in the 1950s. The maximum discovery rate occurred in 1962. Thereafter, the discovery rate gradually declined to the present. This occurred despite a real increase in expenditures from about $200 million/a in 1955 (1982 constant dollars) to more than $900 million/a in 1980. Thus, these data suggest a significant decrease in the exploration success ratio (total exploration expenditures a year divided by the number of significant discoveries) in the last 20 years. As an example, $70 million was spent for each significant discovery in the early 1960s as compared with $225 million in the late 1970s (expressed in 1982 constant dollars). However, with the general declining trend of discoveries, one can perceive a more pronounced drop in 1973 and then a sudden increase in 1974, 1975, and 1976. This increase is probably related to the inflation of the 1970s that in turn created an environment for the explosion of commodity prices, as shown by the commodity price index on Fig. 1. Thereafter, the decline in discoveries resumed in 1975 until the present. Exploration performance by regions North American discoveries are shown in Fig. 2. The graph shows three pronounced high discovery peaks in 1962, 1975, and 1980-81.

Jan 2, 1986

By H. Y. Sohn

The paper discusses two processes, flash ironmaking technology (FIT) and moving-bed ironmaking technology (MBIT), which aim to reduce energy consumption and greenhouse gas emissions in the ironmaking industry by using concentrate directly without pelletizing and without using coke.

Aug 1, 2023