Search Documents

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By Doug Halbe

A number of CIP plants have been built in Western Australia in the past two years. The authors have surveyed several of these new plants and present drawings, data and discussion of operating and design innovations and areas of interest.

Jan 1, 1982

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By E. A. Laurila

During last years many different types of X-ray fluorescence analysers have appeared in the market most of these instruments being designed for laboratory use. The instruments applied ins continuous processes are usually modifications of these laboratory types. The application of these instruments to the analysis of heavier elements seems to be quite satisfactory. By lighter elements difficulties are caused by the strong absorption of the characteristic fluorescence radiation, which sometimes makes the use of vacuum or helium chambers necessary. In the following an instrument of another type will be described. It has been developed exclusively for the analysis of titanium in ilmenite concentrate, where the content of Ti02 varies between 43 - 46%. Preliminary measurements have shown that in this interval absolute change of 1% in the Ti02 concentration causes a relative change of about 2% in the intensity. Because: the accuracy of 0.5 % Ti02 is sufficient, 1% relative accuracy should be, attained in intensity measurement. The problem is not very easy to solve due to the fact that Ti K radiation is rather soft and the requirement's for accuracy are rather high. Being applied to the analysis during a continuous process may statistically fluctuating variables in connection of sampling and disturbances of many kind set special requirements for the instrument design.

Jan 1, 1960

By P. M. Yavorsky

Using a mine roof simulator press capable of duplicating the expected magnitude of vertical and horizontal forces experienced by underground mine roof supports, load capabilities of some roof support cribbings were measured. Comparative ultimate vertical support strengths are reported for cribs of old and new timber and nonreinforced and steel-fiber-reinforced (SFR) concrete blocks. In terms of load- bearing capability, cribs of new hickory and nonreinforced concrete blocks have about equal strength, and SFR concrete blocks are three times as strong. Wood aged 2 years underground lost 43 pct of its support strength. These data were obtained during the course of the initial familiarization exercise of the complex press.

Jan 1, 1984

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By R. B. Taylor

The Esmeralda mine is located about three miles west of the town of Parral, in the State of Chihuahua, Northern Mexico, and about 400 miles south of El Paso, Texas. The area is serviced by the Interamerican Highway and a branch line of the National Railways of Mexico. The Parral district is quite typical of the semidesert of Northern Mexico, lying near the western margin of the Chihuahua basin and range province known in Mexico as the ?Mesa Central? In the immediate mine area, low rounded hills and rolling plans slope toward the Parral River. Surface elevation at the mine is 5,800 feet. The Esmeralda vein outcrops strongly, but was too low grade to be of interest to the Spaniards, The first claims were staked in 1897 and limited exploration work to a depth of 550 feet was carried out prior to 1912, at which time work was suspended. The Eagle-Picher Company acquired the property in 1944 and by surface diamond drilling outlined an orebody to a depth of 800 feet, Minas de Iguala, S. A, de C.V., one of Eagle-Picher?s totally owned subsidiary companies in Mexico, then unwatered the old workings, developed the mine, installed a modern differential flotation plant and started production lage in 1948. To the present, more than two and ahalf million tons of ore have been mined and milled producing lead and zinc concentrates.

Jan 1, 1958

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By Edgar O. McAlister

Associated with cordilleran intrusives of intemediate to acidic composition, gold/silver ores are generally found in the intruded host rocks which are adjacent to these intrusives. Generally precious metal deposits lie further from the intrusives than allied base metal deposits. For vented intrusives, the associated volcanics may constitute the intruded rock and form the host for precious metal accumulation. Potential field methods, particularly magnetics, can help to define unseen boundaries of intrusive systems and thus can point to generalized prospecting targets. Other clues arise from the intrusive system type, its emplacement fracturing, the host rock type and local magnetic changes caused by mineralization processes.

Jan 1, 1984

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

By Rosario Lunar, Jesús Martínez-Frías, Egidio Marino, Trinidad Torres, Jose E. Ortiz, Juan A. Martín-Rubí, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

Seamounts, submarine banks, volcanoes and undercurrent channels are prominent geomorphic features that have become an important target for minerals research and exploration with the goal of future exploitation. Polymetallic ferromanganese deposits are common types of mineralization on these settings. Co-rich ferromanganese crusts are important as potential resources of Mn and Co, but also Ti, Ni, Tl, REEs, PGEs, and other metals. Many seamounts and channels along the Atlantic Spanish continental margin are known to hold mineral deposits but are poorly studied. This work presents and briefly describes the most recent activities of the Spanish Geological Survey (IGME) on exploration and investigation of ferromanganese deposits along the Atlantic Spanish continental margin. Different submarine areas from the northwestern margin of the Iberian Peninsula to the west off Canary Islands have been surveyed by geophysical, sampling and underwater observations from 89 to 4000 m water depth. The mineral deposits cover a large diversity of submarine geological and geomorphical features: mud volcanoes and diapirs related to hydrocarbon seeps, seamounts associated with hot spot volcanism, hydrothermal vents in active magmatic volcanoes, structural basement highs and banks or contourite channels. Considering the collected dataset, we present the preliminary results of the study of these mineral deposits, including ferromanganese nodules and crusts and phosphate pavements and nodules, which can be considered as potential sources of raw materials.

Sep 1, 2014

By Warwick Hoffmann, Robin Batterham, David Conochie

CRA has been actively involved in developing a bacterial oxidation process for the treatment of low grade, refractory gold resources. Success in this application is dependant on the design of large, energy efficient reactors. It was identified at an early stage, that the conventional, bottom sparged bioreactor is inherently inefficient because air must be compressed to a pressure above that at the bottom of the tank. This inefficiency increases as the size of the reactor increases. CRA has developed a novel approach to the aeration problem. In this, venturi aeration is used to aspirate air into a liquor stream. The stream is then reintroduced at the top of a draft tube bioreactor. The advantages found with this technique include · low energy requirements and high oxygen utilisations. From results at the 30 m3 scale, we predict an energy usage of -500 kWh/t sulphur oxidised at a scale of 1000 m3.

Jan 1, 1993

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By R. S. Kalyoncu

Materials demands by the advancing process technologies, desire for higher performance and durability, and improved efficiency in combustion processes, such as applications in heat engines, heat exchanges, and batteries have added to the driving force fueling R&D efforts for the development of components with the combined characteristics of metals and non-metals. These new materials involve refined and specialized microstructures that can lead to improvements in the performance characteristics and durability new technological applications require. Fabrication and sintering methods, once believed to be sufficient, alone, have been found to be inadequate in the manufacture of such advanced components. Realization of the importance of the starting powders has led to efforts to produce materials of ultrahigh purity and ultrafine particle size with very narrow particle size distributions. Such powder characteristics are essential for the fabrication of components with high density and with the desired mechanical, electrical, or magnetic properties called for by the specific application. Novel ultrafine and ultrapure powder preparation techniques are discussed and effects of impurities on the powder characteristics, particle size and morphology, sintering behavior and properties of the finished product are elucidated.

Jan 1, 1992

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By David J. Starbuck

For small precious metals mining to show a comeback a different perspective must be taken than that of larger mining companies. This perspective must be much the same as that of past successful smaller mining enterprises such as when the US had a need for Uranium. Abandoned mines and environmental concerns in older mining districts have discouraged many from entering with the attitudes of why try there if so many unsuccessful mines exist. A small mining venture can be successful there but must have a "think smart'' attitude. There must be a thorough understanding of deposits, utilization of advanced technology and a properly managed mining operation. "THINK SMART" MINING The small mine operator is usually looking for small high grade deposits, consequently, long term success depends on a series of small successful mining operations. The small miner must succeed right-off or credibility and future project funding will suffer. No veteran of even a few years in the mining industry needs to be told that a dollar spent on production today fails to yield as much as it once did. More efficient equipment and techniques have helped soften the problem, but there is little likelihood that a mining company can do much to control inflation, wages, regulations, or grade. That leaves the small miner to "think smart" as one area where operating dollars can still be stretched to produce more than they presently do (Gardner. 1981). In the planning stage of a mining venture, when most options are still open, the main controllable elements are market timing, deposit selection, cutoff grade, mining method, mine design, mining sequence, rate of production build up, process design, project financing structure, project management, and project ownership structure. During planning, optimum criteria can be established for each of these. Once a mine is in production, these options are foreclosed or at least severely constrained. The more thought given to a mining program using all information available the less the risk of encountering disabling surprises. Thus the intent of this paper is to suggest the "think smart" attitude most small mine operations use for long term success. If one looks at a number of successful mining ventures, whether large or small, there is a general logic most have followed to be successful. They have used proven exploration, mining and processing techniques along with economic evaluation and experienced personnel to improve their odds. LOGIC IN DEVELOPING A FEASIBLE VENTURE Most successful small mine ventures achieve positive cash flow as quickly as possible by seeking out those deposits which require the least time and expense on activities leading up to production. To do this they look for deposits that are the most accessible, easily investigated, mined and processed with the cheapest fundamental methods. The general sequence of events starting with district selection are deposit selection, preliminary feasibility, exploration, detailed economic feasibility, mine planning, development and production. Each successive step becomes more costly requiring intermediate decisions along the way. District Selection Small operations should look for known deposits which favor the occurrence of the type deposit sought rather than efforts in unproductive areas. Known deposits in developed areas have some advantages over remote areas: 1. More alternative methods of transportation are available. 2. A larger stable work force is available. 3. The area is usually more pro-mining. 4. Power, water, housing, technical services, skilled services, schools, recreation and shopping are available.

Jan 1, 1987

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991