Search Documents

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

By Klaydison Silva, Pedro Silva, Letícia Damet

The current situation of the global mining economy is increasingly focused on the utilization of materials previously discarded in the mining process. The waste from the past, through new processing routes, is gaining new contours for use as high-value-added products. The strategic mine planning process has consequently had to adapt to the new economic reality. In standard scenarios, the focus was primarily on mine sequencing aimed at the highest economic return, with all infrastructure allocated as a necessity of mining. This work aims, in strategic planning, to configure and select the best composition of mining structures. The entire Mine-Plant-Waste-Tailings-Products chain will be considered as a factor in the sequencing of a multimine complex, to achieve the most sustainable utilization of the current mines’ waste. The sequencing is based on concurrent flows of process configurations and capacities, structure sharing, and flexibility of feed types. These factors will guide the sequencing, which will be constrained by components such as waste and tailings disposal rates, lithology feed relationships, and especially product composition through market specifications, all while respecting product shipping capacities.

Feb 22, 2026

By Ma Lianren, Wang Duolun, Chenzhe Li, Hongyan Xie, Fenglan Luo, Huixin Jin

In this study, the oxidation of low-grade pyrolusite to potassium manganate in alkaline solutions under O2 pressure has been investigated. The effects of different conditions on the high-grade and low-grade pyrolusite leaching process were investigated based on thermodynamic calculation, as well as the reaction mechanisms and kinetics of the low-grade pyrolusite during the leaching process. The results showed that the manganese conversion rates of the two types of pyrolusite were almost the same, and reaching 99% for high-grade pyrolusite and 96% for low-grade pyrolusite under optimal conditions. The optimum condition for low-grade pyrolusite sample JM-2 was achieved as 0.5 MPa of the oxygen partial pressure, 55% of KOH, 14 of the initial alkali-manganese ratio, and ≤ 48 μm of the mineral granularity at 260 °C within 150 min of leaching time and 500 rpm. In alkaline leaching of low-grade pyrolusite, Mn(IV) was oxidized into Mn(VI). The particles changed from large particles to flakes and finally formed crystals. Finally, the shrinking core model was used to fully describe the leaching kinetics of the manganese. It was demonstrated that the leaching of manganese was controlled by the chemical surface reactions and the activation energy which equals 115.9121 kJ/mol.

Dec 3, 2022

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By M. Götze, P. Eysel

Over the last years, the importance of the assessment of environmental and social aspects as well as of issues of good governance has increased significantly in mining finance. For this, international standards as well as internal guidelines of the banks and other involved institutions have been established and continuously improved. Considering these standards and regulations, the banks can influence the sustainability of mining projects - and they have done so in the past -, mainly by implementing certain provisions and covenants in the loan documentation, binding the financing to the mining company’s adherence to the agreed sustainability standards. However, there are limits to the banks’ influence due to the competitive environment with other available means of financing. Nevertheless, the experience of the last years has shown that the standards and regulations bound to the financing by the banks help to lead the mining industry towards more sustainable projects.

Jan 1, 2011

By R. J. Piniazkiewicz

Talc orebodies are mined in Asia, Australia, Europe, North America, and South America. Operators in North America must be efficient quality suppliers to thrive in a talc market in which many overseas suppliers have advantages such as lower hourly wages, shorter distances to ports, and less government regulation and intervention. Continuous improvement through teamwork and innovation is needed in the following areas to thrive amidst worldwide competition: 1) Maximization of the in-place value of ore. 2) Research and development to yield new processes and products. 3) Safe productivity. 4) Involvement in legislative processes. 5) Wellness programs to lower health care costs.

Jan 1, 1993

By J. H. Kelley

In this paper, we show that the methane emission and the dust generation in under-ground mining currently and in the future pose operational, health and safety conditions which adversely Impact face productivity and worker satisfaction. One solution is the use of a dual-aircourse system of ventilation. In this concept, one aircourse captures and exhausts to the surface the dust generated and the methane emitted in coal/mineral fragmentation while a second aircourse provides workers with cleaner air for breathing and comfort. Various dual-aircourse configurations adapted to the Variable Wall Miner are analyzed and compared with conventional mining in gassy seams, indicating a marked reduction in the required air quantity and the number of aircourses.

Jan 1, 1996

By Kristen E. Coose

Concrete is a mixture of a fine aggregate (sand), a coarse aggregate (gravel), cement, and water. Cement itself is the most expensive of the ingredients but generally amounts to only about 10% of the concrete mixture. Cement raw materials include calcium, alumina, iron oxide, silica, and gypsum. They are heated and chemically changed into clinker "minerals," which are then ground and shipped as cement. Each of the four main clinker minerals-tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminoferrite-impart specific strength and compositional properties to the final concrete product. During hydration of the cement, chemical changes produce new minerals that include calcium silicate hydrate gel (C-S-H, the main constituent of hydrated cement paste), calcium hydroxide, and calcium, sodium, potassium, and sulfate ions, among others. Two main reactions can occur that may be deleterious to concrete. Normal cement pore solutions, in a hydrated cement, contain sodium hydroxide and potassium hydroxide. If these alkali concentrations are too high, they can react with the siliceous aggregate (alkali-silica reaction, or ASR) to form an alkali-rich calcium silicate hydrate gel (C-N+K-S-H), which, upon prolonged contact with water, can expand to crack the concrete. The other deleterious reaction occurs when the mineral ettringite (Ca6A12(S04)3OH12. 26H20) forms after the concrete is hardened (delayed ettringite formation) and cracks the concrete. Many of the concrete bridges and structures built in New Mexico in the past 20 years are in need of replacement due to deterioration. Many others constructed very early on in the century are still sound. By collecting and analyzing samples of both old and new concrete and good and bad concrete, we compared their differences on both a microscopic and macroscopic scale. Samples taken from concrete sidewalks, parking lots, drainage canals, spillways, and a railroad-trestle foundation have construction dates that range from 1923 to 1997. They were analyzed by electron microprobe and by petrographic microscopy. Cracks, air voids, and aggregate alteration were primary locations for investigation and analysis. Using the electron microprobe, ettringite was found in voids of most of the samples, both in good and bad concrete. This leads us to believe that ettringite formation is not causing distress in the concrete. There was one exception in which ettringite was found lining a crack. In this instance, ettringite may have the ability to further the cracking and cause distress. No alkali-silica gel was identified with the microprobe. Using the petrographic microscope in cross-polarized light, a light-brown material was observed that lined some of the air voids and cracks; however, exact mineralogic identifications were not made. Although many instances of chalcedony and other deleterious quartz phases were found, no clear evidence of ASR-gel deterioration was present in our samples using these methods. However, positive identification of the ASR gel was made on an in-place concrete near one of our sample sites and in several sample cores using a newly developed chemical test for the soluble potassium ions associated with the gel. The chemical used in this test is sodium cobaltinitrite, Na3Co(NO2)6.

Jan 1, 1999

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By P. Munjal

"Usage of Supercritical CO2 in place of high pressure freshwater has proven to be a potential breakthrough in the technique of fracturing. Tapping of carbon footprints from feasible sources like industries can be used to manufacture Supercritical CO2 required for fracking. Supercritical CO2, being less viscous than water, creates complex and coherent micro-fractures which can connect many more natural fractures greatly, increasing maximally the fractures’ conductivity leading to an increment in production. The better clean-up property of Supercritical CO2 provides auxiliary benefits of immediate evaluation of fracture zones, usage of an optimized quantity of mesh proppant and elimination of the need of swabbing. Also, Coal has a stronger affinity for CO2 than for CH4. When CO2 is present, CH4 on coal is replaced by CO2. This also ensures rigorous recovery of gas from the coal beds. Use of Supercritical CO2 will obliterate many problems as the CO2 used for fracturing is either sequestered beneath the crust or is recovered at the surface and reused. Therefore, injecting CO2 into coalbeds achieves not only enhanced CBM recovery, but also greenhouse sequestration underground. INTRODUCTION Coalbed Methane At various times in the geologic past, earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath the soil. As more and more soil deposited over them, these dead plant remains were compressed. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The omnibus process of formation of coal, thus, comprises of conversion of dead plant matter into peat, followed by its conversion to lignite, then sub-bituminous coal, after that bituminous coal, and lastly anthracite. This process of enrichment of coal as it is progressively forced deeper into an ambience with higher temperature and pressure involves biological and geological processes that take place over a long period and is called coalification. During coalification, large amounts of methane-rich gas are generated and stored within the coal on internal surfaces; hence comes coalbed methane. Coalbed methane (CBM), a gas formed as part of the geological processes that are responsible for the generation of coal, is adsorbed into the solid matrix of the coal during its formation process. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoirs, as the methane is adsorbed and not absorbed. The methane is in a near-liquid state, lining the inside of pores within the coal. The open fractures in the coal that result from the liberation of volatile materials (and subsequent contraction due to the liberation) from the coal due to the high temperature and pressure conditions encountered, called cleats, may also contain free gas or can be saturated with water."

Jan 1, 2015

By Clifford J. Lewis

The control of sulfur dioxide and fly ash in the emissions from coal-fired boilers is a significant segment of the national environ- mental protection program. Developing technologies to accomplish this objective presently emphasize aqueous scrubbing techniques. Should circumstances require aqueous scrubbing for fly ash control only, provision must nevertheless be made to counteract the presence of sulfur dioxide which can create an acidic and potentially corrosive environment. Major technologies for sulfur dioxide control by aqueous scrubbing include, l), recovery processes yielding sulfuric acid or elemental sulfur and 2), throw-away processes which produce a sludge consisting essentially of calcium sulfite or varying amounts of calcium sulfate.1/ Recovery processes are more sophisticated and best suited for locations where there are markets for sulfuric acid or sulfur, or where sludge disposal is an overriding consideration. Throw-away processes are generally less sophisticated but have a problem in that gas scrubbing systems may not operate for practical time periods without failures due to corrosion and to plugging by particulates and precipitates. To overcome this difficulty, some throw-away systems employ an aqueous solution of caustic in the gas scrubbing device to assure maximum water solubility of sulfur compounds, followed by the addition of lime to the scrubbing medium in a system external to the scrubber to produce the throw-away sludge and regenerate the caustic for recycle. Such systems are referred to as double alkali systems.2/

Jan 1, 1975

By C. Xiao, R. Chi

In recent years, the biosolubilization of rock phosphates by phosphate-solubilizing microorganisms has become a major topic of research studies. However, the microorganisms used in previous studies were mostly single and known species, and studies seldom focused on mixed communities of microorganisms or microbial consortia from natural environments. In this study, a microbial consortium from rhizospheric soil was used to solubilize two different compositions of medium- to low-grade rock phosphates — designated as ore samples 1 and 2 — in a laboratory-scale bioreactor. The microbial consortium showed good growth in the bioreactor, reduced the suspension pH and released soluble phosphates from the ores. Scanning electron microscopy with energy-dispersive X-ray spectroscopy showed the action of the microbial consortium on the ore surface. There was considerable corrosion on the ore surface, and 3.42 and 4.93 percent of the element phosphorus was removed from ore samples 1 and 2, respectively. Microorganisms were sampled from the bioreactor for the analysis of their community structures by Illumina MiSeq high-throughput sequencing. The analysis show that the suspensions added with different ore samples had different microbial diversities and richness. This study provides new insight into the biosolubilization of rock phosphates by a microbial consortium directly taken from rhizospheric soils.

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By A. C. Nixon, A. D. S. Gillies, Hsin Wei Wu

Ventilation and refrigeration strategies for the 3000/3500 orebodies, Mount Isa Mines, Australia were reviewed. The orebodies lie between 1,200 and 1,800 m below surface and are characterised by steep geothermal gradients, intensively mechanised stoping methods and high ambient air temperatures in summer. Providing acceptable working conditions under these situations is difficult and costly. The ventilation air quantity required in the 3000/3500 orebodies exceeds 550 m3/s when the production rate is greater than 2.5 million tonnes per year. The maximum quantity that can be supplied and exhausted using the existing intake and return ventilation system is estimated at about 630 m3/s. For production rates greater than 3 million tonnes per year, either new intake and return airways will need to be developed or innovative approaches such as controlled partial recirculation used. A description is given of technical and economic investigations conducted at Mount Isa into controlled partial recirculation. During these investigations, a major field trial of a controlled partial recirculation system was undertaken with results indicating that an acceptable working environment can be achieved practically and economically utilising this approach. The cost involved in controlled partial recirculation for supplying the required ventilation quantity when the production of 3000/3500 orebodies exceeds 3 million tonnes per year is examined. A cost comparison between recirculation and other conventional alternatives such as new surface shaft or underground booster fans is included. The results indicate that the option of a new surface shaft will incur a high initial capital cost and moderate annual operating costs. The alternative of underground booster fans will necessitate a moderate capital cost and very high operating costs. Controlled partial recirculation, in this case, offers both the lowest capital and operating costs of the three options evaluated.

Jan 1, 1995

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003