Search Documents

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By Andrzej Wala

Constantly increasing demand for energy materials and metal ores brought about tremendous progress in mining techniques which are characterised by a high degree of mechanization and concentration of works. One of the recent trends in underground mining mechanization is connected with an application of heavy machines with diesel engines [l],[2]. The introduction of diesel engines in mining all over world caused not only improvement in economic conditions but also the necessity to prevent contamination of air in the mine by toxic agents in diesel exhaust emissions. A generally used way of eliminating exhaust gases is proper ventilation of the cross cut by means of providing permanent exchange of air that would guarantee in every point of the cross cut and in every moment the decay in concentration of exhaust gases beyond threshold limit [3][4][5][6][7][8][9][10]. The present paper is an attempt to define a mathematical model describing the changes of concentration in cross cut face to which fresh air is distributed by ventilators and tubes in a forcing way. Obtained model should offer its practical adaptability to engineering calculation of the amount of fresh air needed for diluting and eliminating exhaust gases beyond threshold limit. Justness of these models has been confirmed by investigation of the growth of nitrogen dioxide concentration in air environment in some cross cut faces of Kiirunavaara iron ore mine in Kiruna (Sweden).

Jan 1, 1980

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By Oscar Letelier Gonzalez

The goal of mine planning is to determine "the best" strategy to exploit an ore deposit during its workable life. Such strategy must be consistent with the objectives of the company and must be subject to the contraints imposed by economical, physical and geological conditions. Mine planning process may be broken down into three categories, according to the planning horizon: Long range, Short range and Operational. The shorter the scope of planning, the higher the level of details and the lower the degree of freedom associated to each plan. A long range plan defines the economic limit of mining at the mining life end of the deposit; it also can be used as an aid in the evaluation of the economical potential of a mineral deposit and as a guide for short range plans.

Jan 1, 1979

By Fred D. Wright, Stefan H. Boshkov

12.1-BASIC AND PARAMETRIC CRITERIA IN THE SELECTION, DESIGN AND DEVELOPMENT OF UNDERGROUND MINING SYSTEMS STEFAN H. BOSHKOV AND FRED D. WRIGHT The criteria governing the selection of an underground mining system relate to several factors the importance of which varies with geographic location, the state of development of the industrial technology, the economic climate in the Nation and, perhaps, in the world-all these as functions of time. Thus, the best choice of a mining method depends upon sets of definable and undefinable values for numerous factors that may be considered fixed at the precise point in time. Subsequent changes in economic and/or technological developments may necessitate modification or complete revision of the existing mining system. A classification of criteria for selecting a mining system must be based on the broadest definitions. Specific cases may present simple solutions or pose very intricate questions, the answers to which are frequently based on judgment rather than explicit logically reasoned and derived results. Specific criteria may be of negligible consequence in some instances and of overriding importance in other cases. It would be foolhardy to attempt to point out, in the limited space available, all possible variations and interplay of factors, as well as to define the setting in which this interplay can take place. The reader is, therefore, referred to the case histories described in the subsequent parts of this section where actual practice will point out the variability of the problems encountered in the selection of a mining method. A popular thesis suggests that the proper approach to selecting the method of mining should be rooted in the inverse solution, whereby the limitations of the various methods in use serve as criteria to eliminate most of these methods from consideration in the specific case. This narrows the ultimate selection to one or perhaps two most appropriate methods. At this stage, a critical comparison analysis will lead to the ultimate choice. Although such a negative approach un¬questionably is valid in discarding obviously inapplicable mining systems from consideration, it falls short in defining the best system, which in practice quite often turns out to be a variation of a textbook standard, or a combination of two or more such standards. Because the deployment of capital and manpower over a long-term commitment closely follows the selection of the mining system, the decision-maker can well afford to spend a great deal of time and effort in evolving the optimum solution for the peculiarities of his specific case. Within the basic engineering tenets of economy and safety to which the design of a mining system must adhere lie numerous factors of constraint which may be grouped, somewhat arbitrarily but for ease of discussion, into several categories. The criteria that enter into the choice of a mining method derive from the following groups of factors: 1. The shape, size and spatial position of the ore deposit.

Jan 1, 1973

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By T. P. Meloy

A methodology is presented for the spreadsheet solution of processing networks performing separations with the methodology developed here a spreadsheet grid is used to represent networks with and without recycle loops. In this manner, network solutions are numerically approximated by spreadsheet grid solutions. The methodology was used to explore the ramification networks developed by the Chinese for tungsten and molybdenum processing. Non-linear stage transfer functions for two-component sharp separations can be used.

Jan 1, 1994

By M. Fan

Dry coal separation technology has particular advantages in the applications in arid and cold regions, or low rank coal separation. The hazardous pollutants in low rank coals can not be efficiently removed by conventional wet coal separation processes because a considerable amount of porose and easily friable low rank coals suffer serious particle size degradation problems in water. In this paper, a novel dry coal separation method with a vibrated air-fluidized bed of magnetic fly ash and magnetite is put forward for dry coal beneficiation. The magnetic fly ash used in this study was derived from fly ash obtained as a byproduct of coal combustion. The vibration?s effect on the uniformity and stability of a magnetic fly ash air-fluidized bed was studied. The 6×0.5 mm dry coal separation results with a vibrated air-fluidized bed of magnetic fly ash and magnetite showed that the probable error E value of separation is 0.06-0.08 t/m3.

Jan 1, 2009

By W. Haupt, M. Thormé, H. J. Ertle, K. Reim

Though Germany has a very old mining history, her experience in uranium mining only started in the late sixties. Today in the Federal Republic of Germany (FRG) there are only 5 small mines in the exploration stage, namely Menzenschwand and Müllenbach in the Black Forest and Mähring, Popenreuth and GroBschloppen in northern Bavaria. In all these exploration mines much development is required to define shape and size of ore bodies. Mining engineers, government authorities and environmentalists alike are very much concerned about environmental safeguards and protection of mine workers against radon and its daughter products. Miners are affected by internal and external radioactive exposure. In general the external [f3]- and [µ] -exposures can be considered as small in comparison to the internal exposure and are therefore not discussed in this paper. The internal exposure is caused by the inhalation of radon and its daughter products and is relevant to the lung as the critical organ. The nobelgas radon is inert and does not from compounds with other elements easily. Contrary to the physical half-life of 3,8 days the biological half-life of radon is only 10 to 20 minutes. During the rentention time in the body only approximately 1 % of the long-lived decay products are retained in the system (SCHOGER, 1976). In this connection is it important that the radon resorption as well as the radon secretion varies individually and depends to a large extent on the age of the person (SCHOGER, 1960). RENOUX et al. (1978) have determined that the greatest part of the a(-activity in the air is attached to aerosoles with a diameter of 0,4/14. The radiation exposure of the lung by radon is negligible if compared with the exposure by short-lived decay products. For this reason one has introduced the concept of the potential [o](-energy (P) of the short-lived radon decay products, which means the total [ct]-energy, which is produced when an atom decays in the decay-series down to the long-lived lead-210. [ ] The unity of the potential [o]-energy concentration in the SI-system is 1 j/m3 air. In radiation protection however a specific unit is used namely the working level (WL): [ ] The WL-unit, though internationally recognised has not been introduced officially in Germany. Because of the large amount of tunneling still to be done in the FRG, the various mines departments responsible for safety and health in mining ask searching questions such as: - What are the laws governing radon emanation in tunneling? - Can workers be adeguately protected against radiation hazards? - How should one drive through high grade uranium ore? - What happens if the ventilation system breaks down?

Jan 1, 1981

By G. L. Dollinger, W. H. Hamilton

INTRODUCTION Design and development of new products generally proceeds through a phase of initial development and discovery based on the evolution of existing arts, followed by technical innovation and development based on both pure and applied research. The development of the mechanical tunnel boring machine (TBM) has followed a similar pattern, with the first machines closely resembling continuous coal miners. In general, however, the design of TBM's to date has been more a result of evolution and discovery than of new technical innovation, even though large sums of money have been spent on research and development. In particular, the results of experimental laboratory and field investigations have had little effect on tunnel boring machine design, and the better performance of TBM's today over those of 10 or 15 years ago, is due more to increased mechanical reliability and greater operating experience, than to improvements in penetration rates and rock fracture capability. The improvements made, have been mainly by the machine and cutter manufacturers who recognize the greater efficiency and economic advantage of utilizing large single row cutters with high load capacity along with large edge spacing. Are there any improvements to be made, therefore, in TBM performance without new and dramatic technological breakthroughs? Can TBM manufacturers design greater performance into their machines by a logical extension of the present art, and by applying what has been learned in the laboratory and field? Some, for example, believe that the kerf cutting system of boring rock is at, or close to, its opti¬mum and little improvement can be made in the present TBM concept.

Jan 1, 1979

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By Neil S. Fishman

Tabular uranium ore in the Grants uranium region, New Mexico, occurs as tabular layers of a urano-organic mixture suspended within host sandstones of the Morrison Formation. The intimate urano-organic association points to the organic material as the main ore control. Petrographic evidence indicates that the organic material was postdepositionally introduced into the host sandstone, probably as humic acids; however, the mechanism by which these acids precipitated from solution remains uncertain. A model, the cation scavenging model, is proposed in this paper to explain humic acid precipitation. The model, supported by evidence from regional alteration studies of the host sandstones, proposes that cations responsible for humic acid precipitation were scavenged from framework grains which altered during passage of the humic-rich fluids through the host sandstone. This process, coupled with the affinity of organic molecules for each other, caused flocculation of humic acids into tabular zones. The precipitated humic substances then continued to concentrate uranium to form the orebodies. The cation scavenging model requires only one solution, the humic-bearing solution, in the precipitation process. All cations necessary for humic acid precipitation originated in the host sandstones. This model contrasts with a previously proposed model--the brine interface or two solution hypothesis--in which it was proposed that a cation-rich brine introduced into the host sandstones provided the cations necessary for humic acid precipitation. The brine hypothesis has several drawbacks, one of which is unrealistic hydrologic reconstructions necessary to accommodate mineralization at various stratigraphic horizons in the Morrison Formation. Moreover, no mineralogic evidence exists to suggest a brine occupied the host sandstones at the time of mineralization. The proposed cation scavenging model for humic acid precipitation not only readily accounts for humic acid precipitation, but also is consistent with geologic observations and regional alteration studies.

Jan 1, 2013

By John P. Anderle

A tectonically disturbed sequence of Mississippian age evaporites expressing a 5 milligal negative gravity anomaly near Sussex in southeastern New Brunswick, Canada, was investigated by a program of drilling, geologic and geophysical work over the past 27 months. Seventeen of twenty-one drill holes have penetrated 10 to 140 feet of potash mineralization in a salt sequence underlying 2 000 to 3 000 feet of arenaceous, conformable red beds, also of Mississippian age. Bromine and borate studies, lithological characteristics and geophysics, have facilitated improved understanding of the salt structure. The salt sequence has been affected by f1owage which has resulted in both major and minor folding. In the more disturbed areas, the potash interval was extensively subterraneally eroded at the upper anhydrite-salt contact.

Jan 1, 1978

By Tom Skodack

Mine and tunnel contractors face a complex environment-one in which economic risks are high, operating costs grow ever higher, ore grades are lower or recovery more difficult, and civil construction projects are intensely competitive on a world-wide scale. Within the context of this environment, the risks and rewards of proper machine selection for rock excavation have become proportionately large. Speed, depth and scope of analysis, and extensive supporting information are indispensable in the selection process. Equipment designs and their applications are also myriad and diverse. Several equipment alternatives and excavation techniques may have to be evaluated at once to choose the most cost-efficient approach. The following examples are typical of the current demand for more detailed equipment analysis: • An aggregate supplier starts a new quarry. He knows his targeted tonnage, blasting restrictions, and previous operating costs from other quarries. But he must improve on his old costs. What drill pattern, hole size, and bench height will give lowest cost per ton? How many crawler drills and what type will produce this tonnage most efficiently? • A mine is using a fleet of twin pneumatic ring drills for long hole drilling to initiate their cave. The mine is facing both air shortages and increasing operating costs with decreased efficiency in the ring drill fleet. If they invest in new hydraulic long hole drills, what impact will each drill unit have on production? Each twin drill unit? What configuration gives best operator efficiency and subsequent reduction in manpower? Which configuration gives the best return on investment? • A tunnel contractor is bidding a long straight water tunnel by conventional drill and blast methods. What is the optimum number of drill booms for the tunnel cross section and excavation schedule? How many rounds per day can he achieve? What are his total project drill, blast, and muck costs? In the past, such questions could be answered, but only approximately at best. One good prediction could involve many hours of laborious calculations that had to be repeated each time a new parameter was introduced or an existing parameter changed. In 1980, increasingly complex analysis, coupled with increasing need and quick response times demanded by industry, led Atlas Copco's project department to turn to the computer. New computer programs based on theoretical considerations and three decades of worksite performance data were developed for evaluating mine and tunnel contractors' equipment needs, productivity, and partial or total operating cost calculations for most conventional drill and blast excavation techniques-including shot rock loading and transportation. This Computerized Analysis of Rock Excavation-or CARE-program has since been available to the mining and construction industry. From each program specific results can be pre- dicted, including: • Productivity Calculations-Rock drill penetration rate for a given drill, hole size, and rock type, optimized for the best drill steel life; net machine productivity (drill-out time or drill meters-footage-per shift); total drill round time, including charging, blasting, loading, and haulage; suggested drill pattern, computer printed, including hole size for a given rock drill, rock type, and associated blasting restrictions for either drift rounds or benching applications; long-hole drill meters (ft) per drill shift; breasting down (upper drilling) drill meters (ft) per drill shift; and comparison between continuous loading machine capacity and LHD capacity. • Operating Cost Calculations-Operating costs expressed as cost per drill meter (ft), cost per cubic meter (cubic yard) of excavated rock, and cost per meter (ft) of tunnel advance. These costs may be calculated using as many cost centers as the mine, quarry, or tunneling contractor wishes. Specific operating costs may cover drill rig operating costs only, less capitalization; drill rig operating costs, including amortized equipment investment; drilling and blasting costs; drill, blast, load, and haulage operating costs; long-hole drilling operating costs per drill meter (ft) or per blasted cubic meter (cubic yard) of rock; and loading and transport operating costs. In all the above cases, any number of cost and capacity calculations may be run by simply changing important cost center variables to judge their net effect. Accuracy as a Function of Input Data and the Statistical Data Base Accuracy of a projection clearly depends heavily on the data base from which the projection is drawn.

Jan 11, 1982

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thor¬ough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield reve¬nues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equip¬ment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Ar¬ranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1989