Search Documents

By Chi-shing Wang

The U.S. Bureau of Mines has been developing the mechanical roof pulling technique as a method for evaluating the effectiveness and the comparative advantages and disadvantages of various roof bolting systems, based on the characteristic responses of bolted nine roofs to a prescribed external loading system. Preliminary experiments were conducted in the Bureau's Safety Research Coal Mine using a 12-foot and a 16-foot-span test rig. The experiments have proved the capability of the test rigs and suggested the viability of the test method. This paper summarizes the test concept and the experimental results.

Jan 1, 1974

The Newmont Boddington Orebody (NBO) is a large, diffuse Au/Cu orebody in Western Australias South-West corner with approximately 20Moz Au in current Reserves. The current sulphide Resource is reported after calculation with the non-linear estimation technique Uniform Conditioning to account for the mining selectivity being smaller than the average drillhole spacing. Simulation of Au grade is also run over the entire orebody reviewing risk and uncertainty. There are differences in results from the two methods. These have been investigated and the lessons learned of the influencing parameters and effect of technique alone, are helpful for applications to other orebodies.

Jan 1, 2010

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

By Steve Kral

For an industry that provides more than half of the nation’s energy needs, the U.S. coal industry still attracts negative publicity. However, the nation’s energy appetite continues to increase. And political leaders and the public are beginning to understand that alternative fuels will not be enough to keep up with that appetite. Does that mean the nation will now embrace the coal industry? No, according to speakers at the Rocky Mountain Coal Mining Institute (RMCMI) meeting. The industry still needs to sell the public on coal’s advantages over other fuels. And the industry must continue to develop technology that will allow coal to meet and exceed strict clean air and clean water regulations.

Jan 1, 2002

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By Robert W. Waytulonis

Miners working in underground mines where diesel equipment is used are exposed to exhaust pollutants. These include carbon monoxide (CO), carbon dioxide (CO,), nitric oxide (NO), nitrogen dioxide (NO2), sulfur dioxide (SO2), hundreds of different hydrocarbons (HC) and particulate matter. Evidence from animal inhalation studies and limited epidemiological investigations have led the National Institute for Occupational Safety and Health (NIOSH) to recommend that ‘... whole diesel exhaust be regarded as a potential occupational carcinogen ...’ NIOSH further stated that ‘... the excess cancer risk for workers exposed to diesel exhaust has not yet been quantified, but the probability of developing cancer should be decreased by minimizing exposure…’ The International Agency for Research on Cancer(IARC) reached a similar conclusion, saying that ‘... diesel engine exhaust is probably carcinogenic to humans.’ Before these declarations, there was insufficient evidence concerning the carcinogenicity of diesel exhaust. It was well known, though, that diesel exhaust caused less severe problems, such as headache, eye irritation and unpleasant odors. In 1988, a milestone was reached in the Mine Safety and Health Administration (MSHA) regulatory process. An advisory committee recommended a three-tier approach to regulating diesels used underground-approval of diesel equipment, safety and health. Diesel particulate matter may be specifically regulated. In addition, ambient air quality standards are being proposed that will establish a new standard for CO2 and lower the permissible exposure limits for the NO2, CO, SO2 and formaldehyde emissions that originate from diesels and other sources. Additional safety and emission restrictions are also proposed for diesel engines in coal mines. The goal of the US Bureau of Mines (USBM) diesel engine research program is to minimize the health and safety problems associated with underground diesel equipment use. Part of this program is focused on reducing exhaust emissions from diesel-powered equipment used in underground mines.

Jan 1, 1993

By W. M. Jr. Aubrey, R. L. Stone

INTRODUCTION Most metallic minerals and some industrial minerals have a relatively high specific gravity and most have at one time or another been concentrated by gravity methods. The principles of gravity concentration are straightforward, well documented and easy to understand, but in practice there are many pitfalls that await the engineer in the development of an integrated flowsheet. Gravity concentration equipment has a long history of use and there is a great diversity available. The equipment is capable of treating material over a broad size range, only falling off in efficiency in the very fine sizes. Gravity concentration is also inexpensive, generally free of environmental problems, and commercial equipment can process large tonnages of ore with a minimum of capital cost. As might be expected of an efficient and low cost process, the bulk of the tonnage quickly and inexpensively. Another obvious application is treating mineral deposits such as hematite and manganese ores that are sufficiently liberated after a minimum of crushing to allow production of a coarse concentrate that will meet market specifications. Except for hand picking and mechanical sorting, there is no competing process on coarse size material. Conversely, it is sometimes obvious that gravity concentration does not warrant consideration. Examples are ores that require very fine grinding to attain liberation, for ores where the minerals of interest have a gravity similar to the gangue, and ores that are strongly magnetic. Actually a mineral processing engineer may not know if gravity is the best way to concentrate an ore, but he should have little difficulty recognizing when gravity concentration deserves consideration based upon specific gravity differences and liberation gravity concentration has wide use. size. His challenge then is to At times its selection as the identify and test the applicable primary concentration process is processes, to develop a obvious. Low grade placer deposits metallurgical balance and flowsheet of tin, gold and beach sands usually for the best process, to estimate are only profitable because gravity production rate over the life of concentration is able to throw away the deposit and to make equipment

Jan 1, 1986

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By Y. J. Wang

A critical path approach is presented for the problem of mine ventilation net- works where regulators and fans are employed to control the airflow distribution which is preassigned. The problem is a classic one which arises in mine ventilation planning. By identifying the analogy between the network for controlled flow and that for CPPI, the applications of the well known CPM technique to the ventilation network problem become straight- forward. The mathematical formulation of the problem is presented and the solutions are illustrated with examples. The effect of booster fans on the total air power consumed in a ventilation network are also discussed.

Jan 1, 1981

By Cherie H. Tilley

The possibility of drilling oil wells from underground locations is not a new concept. It bas not been cost effective for the oil industry in the past and therefore disregarded. Today's state of the art in tunneling and shaft sinking greatly improves the potential for this type of oil field development scheme. This report presents a plan for providing a aeries of drilling bases and the design of the drilling location. The design minimizes the amount of excavation needed to develop the oil field and maximizes the use of rapid excavation techniques.

Jan 1, 1983

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By E. F. C. Ferrett

The benefits derived from the use of main fan evasees or diffusers are well known. If a well designed evasee is fitted to a fan either more air will flow through it or the same air flow rate will be discharged at a lower fan speed. This latter possibility will reduce the air power requirement of the mine, the fan input power and the overall energy costs. Despite these apparent advantages, many reports have been received from the industry of poor evasee performance. After examination, it appears that these problems are often caused by installation difficulties or inaccurate design procedures. The performance of an evasee is affected by several independent factors. Some of these factors describe the evasee geometry whilst others are concerned with the behaviour of the air as it passes through the evasee. This paper shows that the divergence angle is by no means the only ;important parameter which affects evasee performance and that the size of the inlet boundary layer has a significant influence. The performance of evasees of differing geometric shape are compared and the criterion to be used for optimum performance is discussed. It is shown that the commonly used evasee efficiency is a poor indicator of good performance. Recent work by the author and others is evaluated and a simple design. guide discussed. For more sophisticated work, details of a. computer program are provided. Finally, a brief resume of the performance of truncated diffusers is given. Since compressibility effects can be ignored for most mining applications, incompressible flow has been assumed for most of this paper.

Jan 1, 1980

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

By M. Nambiar

Due to the remote locations of mining projects and the need for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short-circuit capacity. To cope with this situation, more and more mining operators are considering the installation of appropriately designed synchronous condensers together with power factor correction and harmonic filter systems (PFC & HFS). The installation of such power quality equipment is viewed as a technological advancement in the mining application. An adequate level of short-circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter-driven gearless mill drive systems (GMDs) used for grinding. This paper explores the impact, technical advantage and reasoning for the selection of this advanced hybrid technology to cope with the power system challenges of future mining projects. It also delves into the potential problems and how to address them.

By C. A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 2001

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014