Search Documents

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management's ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By C. W. Hoffman

A fairly recent development in the field of particle separation is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing as such is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages to be gained by the use of probability sizing vs. conventional screening methods are: reduced space requirements for a high capacity unit, fewer moving parts, more versatile product sizing selection, reduced maintenance requirements and lower power consumption.

Jan 1, 1968

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By M. Khandrika, B. K. Parekh

Column flotation has proven to be the most effective technique for the flotation and recovery of ultrafine coal. The commercial application of columns in the coal industry is steadily increasing (Parekh et al., 1990; Yoon et al., 1992). For the flotation of coal or mineral air is used for generating bubbles. Using a conventional flotation cell, Miller and Mishra (1985) compared froth flotation behavior of fine coal using air, nitrogen and carbon dioxide gas. They concluded that carbon dioxide gas provided a higher rate of recovery and a lower ash content. The objective of the present study was to investigate the effect of various gases such as compressed air, nitrogen, argon, and carbon dioxide on the column flotation of fine coal.

Jan 1, 1999

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

Floc properties such as density, size, size distribution, porosity and shear strength govern the effectiveness of flocculation as a process for solid-liquid separation. Floc characteristics desired for removal of suspended solids by sedimentation or filtration, for example, are known to be different. In this study, an attempt has been made to evaluate floc density using a simplified procedure and determine the effects of various physical and chemical factors on the density of floes obtained. A brief discussion of techniques employed to measure the shear strength of flocs and the effect of various parameters on the floc strength is also presented.

Jan 1, 1988

By Jr. Pickering

Commercial quality kaolin deposits occur in fluvial sediments in both central-eastern Georgia and in the eastern Amazon River area of Brazil. Distinctive coarse and fine particle size kaolin deposits are present in both areas; they have many remarkable similarities for mineral deposits occurring at such wide geographic separation. Industrial, mineralogical, crystalline, and chemical resemblance of the coarse and fine kaolin deposits from the two areas will be described in detail. Knowledge of similarities of the Brazilian clays to those which have dominated world production in Georgia will help to develop superior quality kaolin products for world use in paper, paint, plastic, ceramic, and other applications.

Jan 1, 1997

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986