Search Documents

By Xiaobo Zhang, Panshi Xie, Xiaobo Wu, Ding Lang, Jiandong Yu, Yongping Wu, Kun Feng

In a fully mechanized top coal caving mining process, the mechanical properties of the top coal deteriorate constantly, and the stability of the support is determined by the boundary position of the top coal entering the limit equilibrium state. Top coal flaking occurs more easily along the advancing direction owing to an increase in the distance of the boundary from the wall. Moreover, the strength of the coal seam is an important factor that determines the boundary position. The equation of the top coal limit equilibrium zone boundary, used in fully mechanized top coal caving mining, was determined based on the limit equilibrium theory, continuum damage mechanics, and the Hoek–Brown rock empirical strength criterion. Using the RFPA3D and UDEC numerical analysis methods, the effect of top coal strength on the mechanical behavior during the mining process was determined; and the space–time relationship between the top coal deformation failure, damage evolution, and boundary of the limit equilibrium zone was established. The results revealed that when the coal mass entered the limit equilibrium zone, accelerated crack development, accelerated damage, and axial unloading occurred. Moreover, an increase in the coal seam strength caused the boundary of the top coal limit equilibrium zone to be closer to the wall. By comparing the numerical results with the theoretical results, the overall trend was found to be consistent, allowing the verification of the rationality and reliability of the determination equation of the boundary position of the limit equilibrium zone.

Sep 21, 2021

By Fred J. Fleischauer

Industry requires higher speed sheet stacking. High speed sheet stacking requires equipment and techniques to solve several inherent difficult problems, such as the tendency for sheets to sail, and the need for a means to absorb the kinetic energy of the sheet without damaging the sheet. Accurate alignment of the sheets on the stack is another problem difficult to solve. The paper first analyzes the process of sheet handling into its basic elemental steps. It then describes equipment and techniques presently used for moderate sheet handling speeds, with emphasis on how each step in the stacking process is accomplished by the present equipment. The limitations to speed-up of present equipment is discussed. New high speed equipment, either recently introduced to the market, or in the process of development, is described. Magnetic, air float and vacuum conveyor stackers are compared.

Jan 1, 1973

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By A. Yazadni-Chamzini

Risk ranking of projects is one of the importance parts of the complicated risk management procedure. Recognizing the riskiest criteria enable the managers to plan for risk reduction. The first stage for meeting this aim is defining the risky parameters and then working to establish order between them. There are variety methods for risk ranking. The ELECTRE method is one of the best among the multi criteria decision making methods. In this paper with implementing the fuzzy ELECTRE, The risky criteria in the Tehran Subway project are being ranked. The result of this research presents damage and accident of machineries as well as the lack of labor and equipment safety is located in the first order. Collapse factors and local prices are in second rank. Also wrong design, pollution, urban facilities damageable are in third to fifth respectively. Delay and ? are located in the last positions.

Jan 1, 2012

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By E. Topuz, Xing Wu

INTRODUCTION The air flow in the mine ventilation network can be categorized in three ways: natural splitting, controlled splitting, and semi-controlled splitting. In natural splitting, the air flow in branches of a ventilation network apportions itself according to the aerodynamic resistance of the branches. In controlled splitting, a prescribed quantity of air is circulated through each branch. In semi-controlled splitting, flow in some branches is fixed to a desired quantity while in other branches it is split naturally. In practice, the mine ventilation networks present the latter two situations. Usually, the resistance of each branch in the network is known and the quantity of air in the working place is predetermined by safety considerations. If the number of branches whose airflow quantities are known is equal to or larger than the number of the fundamental meshes in the network, then the network becomes a controlled splitting network (Wang, 1982 a). Otherwise, it is a semi-controlled splitting network. If no booster fans are used in the network, the problem can be solved as either controlled or semi-controlled splitting networks in order to determine the main fan pressure and regulator size and location. All techniques are based on Kirchoff's flow and energy conservation laws and Atkinson's Equation. Booster fans can be used in controlled and semi-controlled splitting networks. It has been proven both theoretically and practically that using booster fans in these ventilation systems can improve flow distribution and reduce consumption of power (McPherson et al., 1985). The current techniques used in determination of booster fan location and size include simulation, linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. These techniques can be classified into two groups. The first group, including linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing techniques, deals with controlled flow networks. The second, simulation, can be applied to the handling of semi-controlled flow networks. Mathematically, the problem of controlled splitting networks can be solved more easily than that of semi-controlled splitting networks. This is because the controlled flow network can be formulated as a linear programming problem, for the solution of which there are several sophisticated algorithms. Moreover, the semi-controlled flow network is usually modeled through nonlinear programming, for which there are no universally applicable solutions. The procedure described by Wu and Topuz, 1986, can be used to convert a semi-controlled network to a controlled flow network, and the problem can then be easily solved by the techniques used for solution of a controlled flow network problem. In practice, a mine ventilation network may change from controlled splitting to semicontrolled splitting with advancement of mining. This dynamic nature of mine ventilation makes the problem more complicated and necessitates development of new solution procedures which will consider the overall economics of the system. CONTROLLED SPLITTING NETWORK The problem in controlled splitting networks with booster fans is to determine the operational characteristic of the main fans, and the location and size of booster fans and regulators. The objective is to satisfy the air flow rate requirement for each branch while minimizing consumption of energy. The techniques used for the controlled splitting network problem include linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. The objective function and constraints can be expressed as follows (Wang and Pana, 1971): [ ]

Jan 1, 1989

By G. A. Perry

Cyprus Sierrita is a major producer of copper and molybdnum from its Sierrita and Twin Buttes open pit mines south of Tucson, Arizona. Both pits were started in the late 60's and are in excess of 1500 feet in depth. Sierrita has utilized a Cat 992C Remote Controlled Loader since January 1993. The loader was justified to increase SAFETY and PROFITS at Sierrita. It has exceeded all expectations. As of June 1993, it had produced additional profits totaling more than $1,500,000.

Jan 1, 1994

This paper presents the development of a knowledge based integrated decision support system (E.X.I.S) for the extractive industries to provide information concerning the environmental impact of extractive operations on land quality, surface and ground waters, and the best solutions for the rehabilitation/revegetation of the waste disposal areas to the relevant target groups (extractive industries, regional authorities, national authorities, research institutes, public). GIS was integrated with the decision-making models for the rehabilitation and revegetation of mine spoil. The system design involves several steps including site selection ? mine type identification ? waste identification ? selection of rehabilitation (revegetation or other methods). The knowledge based model consists of two integral parts: the model base, in which the input data are processed and classified using special fuzzy algorithms and criteria and the knowledge model, which hosts the various decision algorithms concerning evaluation of vegetation covers, selection of trees and plant species, selection of rehabilitation and revegetation schemes and also economic analysis for each option. The system input will include parameters on site characteristics (climate, topography, geology, hydrology etc), waste type and properties (physical-geotechnical and geochemical data) as well as environmental parameters of the existing waste disposal area. Based on the values of the above parameters and the characteristics of the rehabilitation technologies developed worldwide, the system, using IF-THEN rules will define a list of appropriate techniques for the rehabilitation of the examined waste. Then, the model will involve the application of multi-criteria analysis (MCA), i.e. a structured system for ranking alternatives and making selections and decisions. Each technique shall be judged based on its behavior into four fields, i.e. financial, social, technical and environmental criteria. In turn these fields will be analyzed into a lower level of evaluation criteria.

Jan 1, 2006

By Robert S. Shank

Introduction The Pinto Valley open-pit copper mine is located in southern Arizona, 11 km (7 miles) west of Miami. Production at Pinto Valley began in 1974. About 350 Mt (386 million st) of ore and waste was removed by the end of June 1982. At that time, the mine was using more than 90 major equipment items with a total mobile fleet numbering 320. Some of the major equipment consisted of four Marion M4 rotary drills; six P&H 15, 11.5- and 19.1-m3 (15- and 25-cu yd) shovels; and 24,136- and 154-t (150¬and 170-st) Wabco haulage trucks. This equipment was used to move more than 139 kt/d (154,000 stpd) of ore and waste. The mill was processing more than 50 kt/d (55,000 stpd) of mine ore. Shutdown A two-week vacation shutdown began in July 1982. Maintenance jobs were scheduled, and most employees left for the vacation. During the vacation period, copper prices fell below $1.32/kg ($0.60 per lb). Inventories remained at alarmingly high levels. At this point the mine was losing more money operating than it would by being shut down. The vacation shutdown was first extended to five weeks. But, after further evaluation, the mine was shut down indefinitely. In Dec. 1982, Cities Services Co., owner of Miami Operations (which included the Pinto Valley mine and mill), was acquired by the Occidental Petroleum Corp. On March 1, 1983, Occidental sold the operations to Newmont Mining Corp., and Newmont created Pinto Valley Copper Corp., as a wholly owned subsidiary. Copper continued to be produced by the Pinto Valley solvent extraction-electrowinning (SX- EW) plant because of its low cost per pound of production. To ensure proper equipment care during the shutdown, maintenance management was given three goals; • maintain the SX-EW plant; • maintain the environmental and pollution control systems such as domestic water pumps and mine dewatering; and

Jan 4, 1985

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acidinsoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Nov 1, 2011

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acid-insoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Jan 1, 2011