Search Documents

By J. L. Thompson

Lime made in a coal-fired, rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh-percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly 3 orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically inert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime. The total hydration of the chemical complex that is called commercial lime can be more easily understood by considering the individual reactions and combining them to form a more comprehensive picture of the situation. Calcium oxide and magnesium oxide hydrate similarly, differing only in their reaction kinetics. Dolomite, however, reacts differently than a simple mixture of calcium oxide and magnesium oxide as its hydration is strongly influenced by calcination thermo-dynamics and stone grain structure. Finally, the dust hydration and composition should be examined Understanding these reactions enables one to examine hydration reaction graphs with more insight into the factors which determine their shape.

Jan 1, 1978

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By John Hanna

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption and high reactivity of fatty acid collectors towards apatite over silica surfaces under slightly acidic conditions of pH 5-6.5. The process was successful in upgrading various phosphate samples from Florida and North Carolina containing 7.7-15.3% P205 and 62.3- 77.2% Insol to concentrates assaying 28.1-33.1 % P205 and 4.1-9.9% Insol with high P2O5 recovery of 81.8-92.2%. Depending on the type of silica impurities present one or more cleaning steps, with or without sodium silicate, would be required to improve the grade of the rougher phosphate concentrate.

Jan 1, 1992

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine's large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine's ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company's Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana's Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By Carl E. Nelson

Shallow epithermal stockworks hosted by maar eruption craters contain over ninety percent of the bulk mineable gold identified to date in the Circum-Caribbean region. Pueblo Viejo (Dominican Republic) and Santa Rosa (Panama) contain combined gold reserves of over 600 tonnes. Bulk mineable gold deposits are also being discovered in and around veins that were formerly mined underground. Bellavista, El Recio and San Martin (Costa Rica) contain combined announced gold reserves of over 50 tonnes. Representative rock suites collected at 8 bulk mineable gold deposits include 291 samples of veins and vein stockworks, hydrothermal eruption breccias, sinter, variably altered host, unaltered host, nearby intrusive rocks and basement. Analyses completed to date show that Circum-Caribbean epithermal ores are enriched in arsenic, mercury and antimony as well as gold and silver. Exploration efforts in the region naturally focus on districts with past production. However, an order of magnitude more bulk mineable gold has been discovered in shallow epithermal stockworks outside of the old bonanza vein camps. Exploration guides include basal island arc volcanic sequences, hydrothermal and hydrovolcanic (maar) eruption breccias, thinly-bedded carbonaceous maar sediments, and hot spring-related silicification and argillic alteration.

Jan 1, 1990

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Daniel J. Kennedy, George W. Klinowski

A significant portion of each mine is ventilated with the help of auxiliary fans delivering fresh air to the faces of its developing headings via flexible or rigid ducts. Quality and volumes of air delivered to the blind working faces are essential for creation of safe and acceptable conditions for employed crews. Well designed and properly maintained delivery systems are necessary in each mine. The Cape Breton Coal Research Laboratory, part of the Canada Centre for Mineral and Energy Technology located in Sydney, Nova Scotia, Canada, developed a tracer gas based technique which provides fast and accurate evaluation of any auxiliary ventilation system performance. In addition, important information about the system's behaviour is gathered which can be used for designing a similar system in comparable conditions.

Jan 1, 1989

By C. M. Bristow

The mineral kaolinite is one of the commonest minerals in the uppermost 10 m of the continental crust; ranking in abundance alongside minerals like quartz, mica, feldspar and calcite. Only very exceptionally does it possess all the necessary properties needed to make it worth commercially exploiting. The terms 'Kaolin' and 'Kaolinite' are derived from a locality known as 'Kau-ling', in Jiangxi Province, Peoples Republic of China; where samples of a white clay used by the Chinese to make porcelain were first obtained by European missionaries and explorers in the eighteenth century.

Jan 1, 1986

Africa is rich in natural resources, much of which remain untapped. Despite that, international mining companies have largely stayed away from the continent due to political instability in many countries, lack of infrastructure and the inability to gain control of mineral deposits. Today, optimism is growing concerning African mining. Many of its nations are moving toward privatization of their mining industries. They see it as a way to improve the lives of their populations and become politically stronger. Ministers from 22 African nations were Denver, CO in June for the World Bank's Multilateral Investment Guarantee Agency's Fourth Annual African Mining Investment Symposium. The three-day symposium drew more than 400 mining executives and government representatives. Foreign mining investment in Africa is on the increase. In 1996, international mining companies spent about $418 million on exploration. That is more than double the $190 million spent in 1994. Mining executives say the mining climate in Africa is improving because countries are privatizing the industry and rewriting mining laws that encourage natural resource development. They estimate that private mining firms now control about 80% of mining today. Mine development will help lift the living standards for Africans, the ministers said. The average income for ordinary Africans is about $500 a year. If this new mining boom continues, citizens of nearly all African nations will reap the benefits of better infrastructure and government services, as well as more higher paying jobs, the ministers said. They also issued a word of caution to mining companies attempting to join in the African boom. Concerns are being raised about the treatment of villagers and the environment. In the past, foreign companies would "behave about like colonial masters," said Gerald Ssendaula, natural resource minister for Uganda. Africa is in a different position now, he said. "Now we are solving our own problems." Mining companies must respect local communities or risk creating unrest that will threaten fragile new governments, said Akolang Tombale, chief geologist for Botswana. On the other hand, he said villagers must accept that mining development will benefit them. "They feel these are their natural resources. There must be a mutual interaction between the companies and the people."

Jan 1, 1997

By Nasib Al Habib, Hooman Askari-Nasab, EUGENE BEN-AWUAH

In-pit crushing and conveying (IPCC) is getting popular in deeper open pit mines as a suitable alternative to truck haulage because it offers a lower operating cost due to shorter haulage distance and less truck requirement. Semi-mobile in-pit crusher, currently the most popular IPCC system, is relocated every two to five years, and the short-term plan needs to be updated accordingly. To the best of our knowledge, short-term planning with IPCC is an area of research that has yet to be explored extensively, and hardly any model can generate a shortterm extraction sequence considering an IPCC. This research work proposes a mixed integer programming model to develop a short-term production plan within a time horizon of 12 months. The model's objective is to optimally allocate shovels to minimize the cost of material handling and maximize revenue subject to meeting plant requirements, maximum allowable tonnage variation and IPCC location constraints to achieve production and NPV targets set by the strategic plan. The proposed model will be implemented in an iron ore mine case study for verification. The model is developed and solved using MATLAB. The comparison of results between scenarios with and without IPCC justifies the use of IPCC in large open pit mines from a short-term perspective.

Jun 25, 2023

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

By D. A. Harman

The U.S. Environmental Protection Agency recently recognized Newmont and other mining companies, along with the Nevada Division of Environmental Protection for their voluntary work in reducing mercury air emissions. One example of this voluntary effort is the installation of a reactive scrubber to capture mercury vapor from the exhaust of a carbon regeneration kiln at Newmont’s Twin Creeks Mine. After considering the available technologies, a proprietary reactive scrubber, developed by ADA Technologies, Inc., was selected and is currently being commissioned. Mercury removal rates greater than 90% have been documented.

Jan 1, 2004