Search Documents

By Ron Allum, Ed VanDerPas

The application of high speed tunneling in a deep underground copper mine is essential for an ambitious expansion project at Magma Copper Company's San Manuel Mine. At stake is the future of over 1,300 employees at the largest producing full gravity block caving copper mine in the world. A joint venture of Frontier-Kemper Constructor's Inc. and Deilmann Haniel GmbH is helping create that future through the successful application of tunnel boring technology. This paper examines the details required to assemble, deploy and operate a 4.62 m open main beam tunnel boring machine (TBM) in a 1048 m deep operating mine accessible only by shaft.

Jan 1, 1995

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008

By M. Botz

Alacer Gold Corporation is constructing the Çöpler Gold Mine in eastern Turkey. Mining commenced in the fourth quarter of 2009 and gold production started in the fourth quarter of 2010. The mine is a 15,500 t/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production, but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life, approximately 40 Mt of ore will be placed on the leach pad, which will contain about 35,000 t of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the life of the mine. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By J. E. Garlanger

Each year, Florida mines approximately 40 million tons of phosphorite, most of which is ultimately converted to various commercial fertilizers. The phosphorite is mined from within the bottom portion of the 40-to 60-ft. thick surficial aquifer, using open pit mining techniques. The ore zone or "matrix" is generally overlain by relatively permeable fine sand to silty and slightly clayey fine sand. The ore itself is highly variable in nature but, in Central Florida, typically consists of less permeable clayey phosphatic sands and sandy clays with stringers of permeable sand. The ore is much more sandy in the north Florida mining area.

Jan 1, 1990

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By Eugene L. Foster, Gilbert L. Butler

The successful demonstration of a precast segmented concrete liner in the Lexington Market Section of the Baltimore Regional Rapid Transit System (BRRTS) is an important step forward in our continuing efforts to control tunneling costs in the USA. In addition to its contribution to specific savings in future tunnels, this demonstration project has taught other lessons about the U.S. tunneling industry and about the process of "mainlining" new and improved technology into that industry. This paper will present an overview of the Lexington Market Demonstration Project from its beginnings to the present time. In addition, it will discuss other implications which have an important bearing on the extent to which tunnels will be used in future transportation systems in the USA. THE HISTORY Precast segmented concrete tunnel liners are not new. An unbolted version was reportedly used in New York City in the 1930's. The modern bolted configuration has been in use in foreign countries for more than 15 years. Indeed, consideration of the use of precast bolted segments below the water table in the USA dates back to the BART system in San Francisco in the 1960's. At that time, they were evaluated and it was concluded that the state of the art would not allow segments to be precast to the required tolerances. A secondary grinding operation would be required if water-tightness was to be assured, making them economically non-competitive with steel. Based

Jan 1, 1981

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks capable of hauling payloads in excess of 290 t (320 st). Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Because truck haulage costs can account for 10% to 50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, but vehicle operating and maintenance costs would increase prohibitively. Thus, there is a need for improved design technologies encompassing the construction and management techniques of mine haul roads appropriate for the wheel loads of vehicles now in use. This paper presents the different components of a mine haul road design and management system and demonstrates the value of its application through case studies. The system has been applied at several South African surface mines, and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and provided better service, while the optimal selection and management of wearing course materials provided better functionality at lower total transportation operating costs.

Jan 1, 2000

By Anthony Harding, Rodolfo D. Aradas, Juan M. Fernandez, Darío Tsingas

"The adoption of tunneled combined sewerage interceptors and outfalls leads to design linings which are often subject to internal pressures that are larger than the external pressures, resulting in significant tension loads. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining. However, improvements in concrete technology and the need to seek efficiency in terms of time and costs, have driven designers to consider single pass segmental linings. The Riachuelo Sanitation project in Buenos Aires is subject to these constraints both upstream and downstream of a sewage treatment plant. This paper describes how the challenges of up to 2 bar pressure differential have been addressed by careful analysis of soil structure interaction to ensure that the full benefit of external ground pressure is realized, resulting in a more optimal design for the constructor both in terms of cost and time. INTRODUCTION The construction of long sewerage interceptors and outfalls is becoming an increasingly common piece of infrastructure for modern urban cities facing a large water front and estuarine conditions, which are under a significant environmental burden imposed by decades of sustained growth. Such works intercept most of the distributed sewage discharges to then divert them to a central treatment point from which it will be finally diffused via an outfall into a water body capable to accept these discharges under acceptable environmental conditions. Depending on the magnitude of the sewage load to be handled, the configuration of the urban environment and the conditions of the receiving water body, both in terms of oceanography forces and seabed conditions, these schemes will vary in length, conveyance capacity and design and construction requirements. When conditions permit, the current trend is the execution of long outfalls using flexible solutions (such as the use of HDPE pipes) which usually require some form of concrete ballasted weights to resist off shore dynamic forces when directly laid over the sea bed. However, this concept faces limitations when the conveyance requirements indicate the need for large diameters (typically above 3000 m) and also when the outfall needs to avoid deep features off shore such as navigation channels. When this occurs, tunneling, particularly segmentally lined tunnel constructed by TBM emerges as the most feasible approach for large diameter, long deep outfalls. The operating conditions often result in internal pressures that are larger than the external pressures, resulting in significant tension loads in the lining. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining."

Jan 1, 2016

By C. Newman

"Over the past decade, as conventional underground deposits have been depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. As such, there has been a global increase in the application of cemented paste backfill (CPB) in tabular deposits utilizing open stope mining method with a delayed backfill placement. Despite the extensive use of CPB, many fundamental factors affecting the design of safe and economical fill structures are still not well understood. A critical issue in the design of backfilled stopes is the determination of stress states within the fill material itself as well as the surrounding rock mass. Analytical equations provide a means of quickly evaluating the effectiveness of a given design. However, in developing these equations large assumptions are implemented to simplify the design problem. It is important that one understands these simplifications as well as their effect on the overall design. This paper investigates common analytical equations utilized in the evaluation of single vertical backfilled stopes and their assumptions through comparisons to numerical modeling results. INTRODUCTION AND BACKGROUND As the mining industry continues to produce at greater depths and in more geometrically and geologically complex conditions, cemented paste backfill (CPB) has gained traction as a means of providing localized ground support in modern stope-and-fill mining operations. The application of CPB in stope-and-fill mining as a ground support material has led to the reduction of mine waste costs, while increasing both mine production and stability. In an attempt to achieve total extraction of the mining reserve, stope-and-fill mining operations often employ a primary-secondary excavation-support sequence (see Figure 1). In this practice, primary stopes are initially excavated and then backfilled in a two-stage pour; plug and final pours. During the first stage (plug), a CPB material with increased cementitious content is placed at the bottom of the stope providing a strong base from which to build a backfill structure as well as protect mine works from material breakthrough. Following placement, the backfill plug is allowed to cure to a given strength as designated by the mine design. Upon achieving the required cure strength, a less cementitious CPB material is used to backfill the remaining stope area. This is referred to as the final pour stage. With all primary stopes excavated and supported using backfill, the extraction of the secondary stopes commences as primary stopes are utilized as artificial pillars. While the application of CPB in a primary-secondary extraction-support mining sequence allows for a substantial increase in reserve recovery, it is imperative the mining personnel and planning engineers have a clear understanding of the material’s behavior and stress interaction with the surrounding rock mass to ensure the most efficient, cost-effective, and safe extraction of underground deposits."

Jan 1, 2018

By Gordon R. Wicker, Peter V. Avotins, Steven S. Ahlschlager

Laterite ore slurries exhibit Bingham plastic behavior and can be characterized by the magnitude of their yield point and Bingham viscosity. These two parameters are affected by ore composition, solids concentration, and temperature and are used to predict the pressure drop in pipelines and heat transfer coefficients in shell-and-tube heat exchangers. In cycloning of laterite slurries, the calculated cut size is corrected by factors obtained from the rheological parameters.

Jan 1, 1979

By David Cronan

"Most of the recent renewed interest in manganese nodule mining has been focused in the Clarion-Clipperton Zone (CCZ) in the NE tropical Pacific where nodules are rich in Mn, Ni and Cu. However, equally interesting, but compositionally different, nodules occur in the tropical central South Pacific (CSP). The CC Zone deposits lie in the International Seabed Area whereas those in the South Pacific lie mainly in the Exclusive Economic Zones of Island States, principally the Cook Islands and Kiribati. The CSP nodules should not be regarded as an alternative resource to CCZ nodules, as they are enriched in different elements. Rather, the CCZ nodules should be thought of as a source of one group of metals (Mn, Ni and Cu) and the CSP nodules the source of another group (see below), mutually complementing each other and to be mined in parallel for their different metals.Manganese nodule mining in the South Pacific has been mooted since the 1970s. However, new data on manganese nodule composition and abundance there have recently appeared. Also, a recently developed interest in 'rare', 'green' and 'technology' elements has necessitated a re-examination of old South Pacific nodule data for information on these elements (previously thought to be economically unimportant), and the re-analysis of the deposits to obtain new data on them. Additionally, current and possibly future applications to the UN to extend island 'continental shelf' areas necessitates an appraisal of the manganese nodules in these areas. These developments have prompted recent work that has helped to refine our understanding of the distribution and abundance of metals of traditional interest in South Pacific nodules, namely Mn, Co, Ni and Cu, but has also drawn attention to other elements of possible economic interest including titanium (Ti), vanadium (V) and the rare earth elements (REE)."

Sep 1, 2014

By P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber, caulks, and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness, and outstanding rheology in water systems. The quality of calcitic GCC ores, which include chalk, limestone, and marble, is dependent on calcite purity and the nature and quantity of ancillary minerals. Wet and dry grinding is used in the manufacture of GCC. Ore processed by optical sorting, flotation, and/or particle size classification has higher brightness and lower abrasion. GCC markets are a function of the product's properties, purity, and cost.

Jan 1, 1995

By Charles A. Beasley, Vince Joyce, David E. Beasley, Orlando A. Gallegos, David A. Shuman, Mehmet H. Erten

COAL CHARACARISTICS AND PREPREPARATION REQUIREMENTS Preparation and Market Specifications The national ambient air quality standards (NAAQS) established by the Environmental Protection Agency in 1977 require that when coal is burned, the environmental degradation should be a minimum. For this reason, even coal containing low ash and sulfur must be used in compliance with the NAAQS. The most important pollutants resulting from the combustion of coal are ash, SO2, and NOx gases, and the particulate matter escaping with the combustion gases. The ash is the residue left after complete combustion of coal. It results from the inorganic mineral matter existing in the coal before it is burned. The SO2 results from the combustion of inorganic and organic sulfur associated with the coal. The inorganic sulfur may occur as pyrite, marcasite, or as sulfate sulfur of mostly iron and calcium. The authorities disagree in the definition of organic sulfur in the coal. However, according to ASTM Standard D2492-77,1 the organic sulfur is that sulfur occurring in the coal after subtracting the sum of pyrite and sulfatic sulfurs from the total sulfur in the coal. The NOx gases are produced from high temperature oxidation of nitrogen in the coal that is released into the atmosphere. The particulate matter may consist of fly ash and unburned coal. Selective Mining The cleaning of coal from included ash and sulfur-bearing materials should start at the working faces of surface or underground mines. This can be done by (1) mining only those seams which meet certain quality standards, (2) not mining sections of the seams which may cause deterioration in overall quality of the mined coal, and (3) using a mining method that allows selective mining of coal areas or horizons either underground or on the surface. Since these steps improve the coal quality before the coal reaches the preparation plant, they can be considered to constitute precleaning of coal. During the exploration and development stage of a mine, core and channel samples taken from the coal seam are used to determine (1) petrographic analysis and physical properties,2 (2) character of roof and floor of the seam, 3,4 (3) character and quality of impurities,5 (4) proximate and ultimate analysis, and (5) washability characteristics. However, all of these parameters are subject to considerable variation even within the same seam during the advance of the coal face. This creates a problem in meeting the market demand for coal quality if the coal is to be shipped directly from the mine. If the mining operation is large enough, special blending silos or mechanical blending systems may have to be used to provide uniform quality to the market. However, even if the coal is shipped from a coal preparation plant, prepreparation

Jan 1, 1991

By W. R. Reed

This study evaluates the roof-bolter canopy air curtain (CAC) system in an exhausting face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. Two scenarios are considered: (1) a roof-bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof-bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment that contains 6.0 mg/m3 of respirable dust and is ventilated by an exhaust curtain with 9,000 cfm (4.25 m3/s) of air to simulate the roof-bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8 percent. When the roof bolter is operated close to the face, increasing CAC airflow was required for adequate protection, as the dust reductions can be as low as 39.5 percent. Increasing CAC airflows to 350 cfm (0.17 m3/s) and 450 cfm (0.21 m3/s) were evaluated, demonstrating that dust reductions increased to 59.7 percent (350 cfm) and 72.0 percent (450 cfm). These results revealed improvement in respirable dust reductions compared to the CAC airflows at 250 cfm when the bolter is operated close to the face, showing the CAC can provide protection against high respirable dust concentrations for roof-bolter operators.

By Edward C. Mabbs

U.S. industry must increase its productivity or lose its competitive position in the rapidly expanding and inter-dependent world markets. Recent improvements in material handling techniques and equipment, coordinated with production processes, provide one of the greatest opportunities to increase productivity. Successful managers must learn how to take advantage of these material handling opportunities to gain competitive position.

Jan 1, 1973

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By Frank C. Schora

The Institute of Gas Technology for many years has dedicated a large portion of its research effort to the development of a practical solid-fuel-based gasification process to produce a synthetic natural gas equivalent. The work is being done to prepare for the day when supplemental gas will be needed. This program, initially supported by the American Gas Association, and now by both the Department of Interior's Office of Coal Research and the American Gas Association, has developed the IGT Hydrogasification Process. This process, now entering the pilot plant stage, is based on the high-temperature, high- pressure hydrogenation of coal with a hydrogen-steam bearing gas. Product gas from this step is cleaned and catalytically methanated to produce a high-Btu gas. Estimated production costs indicate the process will be competitive with natural gas in certain areas of the country when required.

Jan 1, 1969

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975