Search Documents

By Dennis Greene

Real-time GPS position monitoring of mining equipment is becoming more and more commonplace. Digital mining plans can now be used onboard properly equipped earthmoving equipment and excavation status is available in real-time via high bandwidth data radio systems. These systems provide a closely integrated link between operations and planning. No longer must operations wait for or be hindered by insufficient survey marks, nor is engineering delayed by lack of timely mine status information. Unprecedented efficiency gains become feasible -from the engineering office, to drilling and mucking, to reclamation, as well as in mine construction projects. Direct economic benefits of these systems will be explored as will the less tangible, but very significant, indirect operational efficiency gains.

Jan 1, 1998

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997

By R. L. Wiegel, G. R. Oswald

The processors of Florida phosphate rock face constraints similar to those of other mineral operations--leaner ore, more complex treatment schemes and a product which sells for a penny a pound. IMC Fertilizer is a dominant producer in this market with its current operation of five processing plants. An emphasis by their management in maintaining and improving plant performance has continued unabated for some 15 years. This has resulted in a commitment to the importance of routine automatic sampling of product and in process streams, the generation of reliable assay and size distribution data, the accurate measurement of process flows, and the computerized "rendering" of this information into weekly and monthly material balances which provide consistent measures of process performance. In addition, there has been a parallel program to monitor and improve the performance of flotation reagents and to evaluate process modifications or changes in equipment. This paper will describe the evaluation techniques that have evolved over this period and indicate how the historical data base is used to identify plant problems early and help in their solution.

Jan 1, 1991

The thermal field of a frozen rockmass surrounding an airway is often disturbed due to thermal interaction with mine ventilation air. Outside air entering an underground mine changes the parameters of the physical state of the surrounding medium. The variations in air temperature result in stress redistributions around a tunnel or mine working. This paper examines the influence of fluctuations in air temperature on stress distribution around an airway, and approaches are suggested to minimize the impact of temperature- stress on the stability of mine openings in far northern mines.

Jan 1, 1991

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017

By Abbas Zaidi, Betty L. W. Ou

Wastewaters generated during the extraction of gold from the ore can contain a variety of contaminants such as cyanide, heavy metals and arsenic. Proper management of these wastewaters is therefore necessary to minimize the negative impact of gold mining and milling operations on the environment. The Wastewater Technology Centre (WTC),located in Burlington, Ontario, Canada, has been involved in several studies related to the evaluation of various effluent treatment technologies which are relevant to the treatment and proper management of gold mill effluents. These studies have included bench and pilot scale tests, and the evaluation offull-scale systems. Furthermore, the WTC staff developed protocols for cyanide analysis in gold mill effluents, and a mathematical model for predicting the degradation of cyanide in tailings ponds. The information generated by the WTC staff has been referenced in several reports and papers published over the last ten years (Schmidt et.al. 1982, Simovic & Snodgrass 1989, Whittle et.al. 1989, Zaidi et.al. 1989, Zaidi et.al. 1991). Recently, the WTC has started to develop a micro­computer based expert system for use by decision makers in the gold mining industry and relevant government agencies who are involved in process design, process evaluation, costing, evaluation of the best practicable technology, approval of suggested effluent management systems, and so on. This paper presents some relevant background information and a discussion of the latest version of the expert system being developed by the WTC.

Jan 1, 1992

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By R. W. Fedors, S. T. Green, F. T. Dodge, D. B. Walter

Spatial and temporal temperature variations in a high-level radioactive waste repository drift can give rise to moisture transport within the drift. Knowledge of this moisture transport may be important to assessing the potential for corrosion of all metallic components in the drift. The model presented here shows one approach to simulating evaporation, transport, and condensation of water in large underground openings using a framework based on computational fluid dynamics. Simulation results that explicitly model water and latent heat transport are presented.

Jan 1, 2004

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Stephen Slot Odgaard, Simon D. Taylor

Phase One of Copenhagen Metro opened on October 19th, 2002 and is already a great success. 11 stations are open and Phase Two with 6 additional stations will open during 2003. Phases One and Two include 21 km dual track, whereof 10 km is in tunnel. 17 stations (six deep, three shallow, and eight above ground) will service passengers with trains running at 90 seconds intervals. This paper will discuss the various aspects of the Metro, where construction methods include TBM bored, NATM, Cut & Cover, Secant Piles and Diaphragm Walls.

Jan 1, 2003

By A. S. Henderson

Eastern Mesabi taconite is one of the hardest rocks known, but fortunately it shows little tendency to pack in the crushers, when the minus 5/16 inch material is removed. The crushing circuit is essentially as shown in the Engineering and Mining Journal article, "Reserve's New Taconite Project", dated December, 1956 except that the grizzly screen between the two stages of gyratory crushing has been eliminated. The Reserve operating staffs aim is to utilize the crushing equipment in such a manner that the maximum tonnage of taconite can be crushed to the required size at a minimum cost. As is readily apparent, the primary consideration is to produce a desired size product, with the other operating factors to be balanced, thus achieving the best setting for each crusher. Much effort has been expended toward the development of a satisfactory sized material for feeding the rod mills. The characteristics of this feed must allow the following situations to be handled by the existing equipment: 1. The material being fed to the rod mill must be such that it can be fed into the unit with the proper quantity of water to maintain the correct density within the mill. 2. The rod mill must produce a product from this feed which can be handled without difficulty by the magnetic cobbing and ball mill circuit. 3. The incidental tramp must not exceed that quantity which can be handled easily after the rod mill and after the ball mills.

Jan 1, 1959

By S. B. Keith

Cerro de Pasco Corporation operates five large base metal mines in Peru having a combined production of some three million tons of ore a year. An integrated complex of concentrators, smelters and refineries produces annually about 25,600 short tons of copper, 48,100 short tons of lead, 60,500 short tons of zinc metal, 102,300 short tons of zinc concentrate, 8,272,000 ounces of silver and substantial amounts of bismuth, cadmium and selenium. Geology plays an important role in these operations. The organization of detail geologic work in and around the Cerro mines was set up by John M. Boutwell in 1918 and a geology department was established in 1920. Growing through the years, the department technical staff now numbers over thirty men and. their work covers all phases of geological investigations. Many outstanding geologists of the past and present, too numerous to name here, have studied and contributed to the knowledge of the deposits and the ever growing list of Cerro "alumni" must rival that of any other mining organization. Numerous papers on the geology of Cerro's mines can be found in the technical literature and several doctoral theses have been presented on Cerro subjects as indicated in the attached bibliography, Specimens of Cerro's ores can be found in museum, college and university collections throughout the world. Yet, as with all mines and mining districts, the geologic knowledge of Cerro's deposits in Peru is being revised and added to constantly. This presentation cannot hope to cover adequately all the phases of the geology and mineralization. For a more complete background and discussion of the mine you are referred to the bibliography. Here I shall outline only briefly the more important geologic features and describe some of the newer developments of recent years The credit for the data presented here belongs to the many geologists who have worked or are now working for Cerro de Pasco Corporation, but I must assume sole responsibility for any omissions or variations in the interpretation of their work.

Jan 1, 1965

By Christian F. III Baiz

Introduction A new mining agenda is before us. Born of government policies and world economies, the years ahead will show reduced growth. Metals, mining, and most other natural resource industries are inflation dependant and capital intensive. For these, a long period of contraction of outmoded and costly capacity will evolve. In some cases, this will be supplanted by new, lower cost capacity. But this will occur only if the cost of production - including cash operating and debt service costs - comes in at or below current market conditions. The industrial outlook for metals mining can be characterized as bearish. A US bank economist said mining companies planning their five-year forecasts should take current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or decline slightly. As a result, capital funding will be problematic. The low-cost producer will succeed. That means only the producer with low cash costs and low principal and interest costs per unit of production, will succeed. Gaining a perspective One must look back 30 years to see the evolution of the capital markets, for metal mine financing. This period can be divided into two economic periods. The 1950s were a time of stable economics. Mining companies earned and reported good profits. They had good corporate creditworthiness. In essence, mining companies of the 1950s were highly self-reliant. When equity infusions were needed, they were easily obtained. Financial management kept long-term debt low. Fixed rate, long-term financing was readily available in the long-term bond markets. The commercial banks of the 1950s were rarely used by the mining industry. When necessary, mining companies went to the banks for short-term financing - the kind that was needed for working capital requirements. Changing rhythms In the old rhythm there was an orderly market. Even into the mid-1960s, 75% of world annual copper production was controlled by eight companies: two in the UK, one in Belgium, and five in the US. During times of poor market demand, these producers would control supplies to the market. They took their losses out of retained earnings. Capital was easily restored during the ensuing good times. The new rhythm called for copper to be an economic means to a political end. Third World copper producers brushed aside the market fundamentals of commodity economics. Yet, the political solutions of these countries - their lack of response to the market - have seldom achieved their original objectives. Each commodity has its own old and new rhythm. Aluminum may have a similar rhythm, coming 10 to 20 years later than copper. By the late 1960s, changes were occurring. Inflation was on the rise. Ore reserve quality was falling. As a result, capital expenditures were necessary to maintain existing output. These costs created an increase in corporate leverage, thus adding to inflation and rising interest rates. Indicators A comparison of the gross national product (GNP) deflator index, consumer price index, and the metal mining deflator index is instructive. (Fig. 1 and Table 1). With 1972 equal to 1, note that the metal mining deflator reached its lowest point in 1967. From that point, the metal mining deflator has accelerated severely for 16 years. Only two minor downturns occurred during the business recessions of the mid-1970s and the early 1980s. In essence, Fig. 1 shows that while GNP has grown modestly, a miner's dollar in 1972 would require $3.48 in 1980. This is an almost 17% compounded growth rate over that eight-year period. Beginning in the late 1960s, for the first time in mine financing, the risk of success shifted from the corporate balance sheet to third parties. Limited-resource financings were taken up by banking syndicates that accepted certain of these risks. The lender needed to be well acquainted with the types of risks to be evaluated. These include resource quality and quantity, construction and completion, capital and operations costs, market risks, force majeure, and political and exchange rate risks. Project financings became the basis whereby mining companies were able to maintain their borrowing capacities. In essence, the lender was willing to share some of the project risk while only receiving lenders' returns on these investments. Over the last two decades, mineral project financings have become highly complex transactions involving multicurrency, multi-

Jan 8, 1985

By Ivano Andreis, Georgios Kalamaras, Mario Liti, Sebastiano Pelizza, Filippo Avesani

"THE SS640 AGRIGENTO-CALTANISSETTA PROJECT The Caltanissetta tunnel is part of the works for the construction of the second 28km-long maxi section of the SS 640 motorway of Porto Empedocle, from km 44 to the junction of Imera in Sicilian hinterland. Amongst other major infrastructure works, the €740 million ANAS (Italian national roads and highway administration agency) project consists of four twin tube tunnels three of which are being excavated by conventional means. The longest tunnel, underpasses the Caltanissetta city and has a length of 3.9km under a maximum overburden of 120m. The JV consisting of CMC of Ravenna and TECNIS SpA won the design & built tender in 2010. Construction started in early spring 2012 following the approval of detailed design and later on the approval of design for construction. THE CALTANISSETTA TUNNEL The Design Phase Tender design and detailed design foresaw the construction of 13.4m excavation diameter tunnels that were to be enlarged in a second phase to create, every 600m, 50m-long tunnel sections for emergency parking. During the design for construction project phase the JV proposed to replace the 13.4m tunnel with a 15.08 excavation diameter that incorporated apart from the two 3.75m wide lanes a 3.25m wide continuous emergency lane. This significant tunnel section modification was associated with better road safety conditions, simpler and safer construction procedures, better statics for the tunnel section while in terms of overall cost the solutions were equivalent.Geologic context The tunnel is located in the middle of the geologically known Caltanissetta basin that is intersected by various tectonic structures. The geologic context for the tunnel scale, was defined in collaboration with the University of Catania in early project phases. For almost its entire length the tunnel is excavated in the Terravecchia formation that represents the lower part of the stratigraphic sequence that was formed in the Tortoniano period of Miocene. The quite complex geological model is also characterized by the presence of the so-called Trubi formation that consists of clay and marl clay. Almost 90% of the tunnel traverses formations that are quite similar in terms of excavation behavior. Exception to this are thrust zones and a calcareous stretch of the alignment. This last segment has a length of 200m and was identified since the very beginning as a tunneling challenge due to the combination of very poor geotechnical properties and an important water load."

Jan 1, 2016

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991