Search Documents

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By D. Rumenjak

Fuzzy logic is a useful tool for Sustainable Development (SD) decision making because it can express uncertainty, both in the informational and in the decision-making environment. The general linguistic definition, acceptability for environment (air, water, nature, risk, etc.), as well other aspects of sustainable development (health, management issues, etc) is proved to be useful in approximate reasoning and decision-making. According to this definition, the various fuzzy functions of environmental acceptability can be constructed. This construction is based on the concept of special kinds of fuzzy functions generally defined as Linguistic Variables (LV), which are suitable for mapping to fuzzy sets. Various SD indicators could be used as domains of such functions, expressed either in their physical values (e.g. production, emissions, risk of accidents) or in Measure of Preferences (MP). The most important MP are mentioned below: Stated Preferences Techniques (SPT) of economic evaluation of environment, economic instruments of environmental protection mostly based on Revealed Preference Techniques (RPT), preferences scales (ordinal, cardinal) according to various methods of their construction, etc. Also, the possibility theory (analogous to probability) could be exploited in such construction. It could be used together with environmental engineering modelling formulas for the purpose of determining fuzzy functions. The appropriate forms of linguistic variables, considering limit cases for this purpose, are also discussed.

Jan 1, 2007

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By J. Espí

The mineral price assigned in mining project design is critical to determining the economic feasibility of a project. Nevertheless, although it is not difficult to find literature about market metal prices, it is much more complicated to achieve a specific methodology for calculating the value or which justifications are appropriate to include. This study presents an analysis of various methods for selecting metal prices and investigates the mechanisms and motives underlying price selections. The results describe various attitudes adopted by the designers of mining investment projects, and how the price can be determined not just by means of forecasting but also by consideration of other relevant parameters.

Aug 1, 2013

By Randy Clarkson

Sluiceboxes which are designed and operated as recommended from our recent research can provide much higher concentration ratios than most other gravity concentrators (up to 50,000: 1) at very high overall placer gold recoveries (95-99%). They are also very reliable, inexpensive and simple to operate. A sluice­box is a rectangular flume containing riffles on matting, through which a dilute slurry of water and gravel flows. However, sluiceboxes operating under ideal conditions are actually cen­trifugal concentrators whose riffles overturn ribbons of slurry to form vortices. At the bottom of these vortices, centrifugal and gravitational forces combine to drive gold particles into matting (figure 1).

Jan 1, 1996

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By Ed Ramsay

The Hill is a cyanidation plant with flotation and roasting. The grinding and treatment have at the present time a capacity of 1400 tons of ore per day and the precipitation has a capacity of 6000 tons per day. The ore is delivered by a 36" conveyor belt and tripper to 8 mill bins having a capacity of 6000 tons. The ore from these bins is discharged onto 20" gathering conveyor belts which are regulated with p.i.v. speed changers to control the belt weight. A weightometer determines the tonnage milled. The feed enters the 8' x 12' rod mill through a rubber lined chute and the product is discharged through a launder to a 7' rake classifier in closed circuit with 10' by 6' hardinge ball mill. Lime slurry is added at the rake classifier to give a strength of .30#/ton. The classifier sand is fed into the ball mill with a scoop feeder and the mill discharge flows in a launder back to the classifier. The classifier overflow is pumped to a 24' by 12' bowl classifier in closed circuit with a 8' by 15' regrind mill. The bowl classifier sands are fed to this mill and the mill discharge is pumped back to the bowl. The bowl overflow at 8% - 200 mesh is the final product from the grinding circuit.

Jan 1, 1975

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By C. S. Boland

The Copper Range Company's mining properties are located in the Upper Penisula of Michigan. (Fig.). Early work indicated the presence of copper ore in a bedded deposit, confined to the base of the Upper Keweenawan Nonesuch shale, and exploitation of this deposit on a portion of the Company's property was undertaken by White Pine Copper Company. Diamond drilling of the White Pine orebody indicated that a major fault pattern terminated the values to the South-west. Further drilling Southwest of the fault zone proved a downward displacement of the ore bearing horizon some 1,500 feet and a lateral displacement of approximately 4,000 feet; and in this area an ore deposit was outlined in a large asymmetrical syncline locally plunging to the South-west. (Figs. 2 and 3)

Jan 1, 1962

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year's increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers' demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By C. Treworgy

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Jan 1, 1997

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By Rahul Bhaduri

Mercury levels in Twin Creeks Vista pit ore (previously Chimney Creek, North pit ore) increased substantially since plant start-up in November 1987. Consequently, modifications were necessary to minimize industrial hygiene hazards and potential operational problems. The original plant design included mercury control measures. With progressive increases in mercury levels, the issue had to be re-addressed. Modifications to operational practice, industrial hygiene and management philosophy will be discussed. Additionally, a detailed examination of the mercury vapor suppression system currently employed at Twin Creeks will be presented.

Jan 1, 1994

By Marcus Digre

The autogenous grinding method has been progressively employed in mineral dressing plants during the last 15 years. The term has been used with somewhat different meanings (1), (2), (3). In this paper the author will use it in the most restricted way, for processes where run-of-mine ore (rock) in one step is reduced to a grind product by the action of the ore itself without any other grinding media present. The pebble grinding process where the major part of the ore enters the mill as finely crushed product which is ground further with selected coarse ore pieces acting as grinding media, is not considered autogenous grinding. Processes where a minor amount extraneous media as steel-balls is added to supplement an autogenous mill charge will be called semiautogenous. Other terms need also to be defined. "Mill charge" will be used about the active part of the mill content which performs the grinding, that is the steel balls in ball grinding and the coarse ore pieces in pebble and autogenous grinding. The interstitial nearly finished material is not included in the term "mill charge", and for the wet grinding operations is called the "mill pulp' The term "pebble" will be used for any rounded ore or rock piece in the mill charge whether it is an autogenous or a pebble grinding operation.

Jan 1, 1970