Search Documents

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By H. EI-shall

In this paper, the results of a fundamental study involving zeta potential and turbidity determinations of solid suspensions are discussed. Illustrations of how these results are utilized to design field applications of solid grade polymers to clarify mine drainage water are presented. Other applications in different industries are also reported. The operational and economical advantages are examined.

Jan 1, 1994

By William J. Dimond

Computor analysis has opened a new world of information for the mining of resources. This paper is directed at the mining of coal. The same procedures apply to most mining projects. The available facts when evaluated against the variables produce the answers. The project must be carefully analyzed, so that the facts can be organized in a data file. The file can be expanded as additional information is obtained during the entire life of the mine. If the mine is pre-planned, the file will be expanded in an orderly fashion and updated information will be available at all times. The development of a property goes through several phases; Exploration, Economic Analysis, Development, Production, and Reclamation. Each phase is an expansion of the data file. The validity of the answers is directly related to the accuracy and quantity of available data. The basis for a data file is horizontal position, and elevation of each piece of information. A coordinate system and datum are reference for a digital (X, Y and Z) position in a spatial system, a three dimensional digital model of the mine. The current practice is to use the State Plane Coordinate system and elevations as established by the U. S. Coast and Geodetic Survey. Each state has adopted this system by law. In the event there is litigation, it is an advantage to have the data on the legally recognized system. The control must be expanded so that all data can be assigned a digital position, and planned to fulfill the requirements for all phases of the mining operation. The project must be analyzed to insure that the objectives can be achieved without duplication or loss of time. sufficient data must be available to reach each required level of information. The coal data can be defined in two categories, spatial

Jan 1, 1977

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By John J. McCrone

In the Mining Industry, the means of handling and transferring lubricants has been given little attention over the years. An analysis of this process indicates that this neglect has often exacted a very high price. As the costs associated with labor, equipment utilization and waste disposal soar, the need for an efficient system takes on an increasing significance. Often the focus of bulk systems has been placed on the master container itself. Certainly, there is nothing new about a large lubricant container; they have been available over a period of years, known under a variety of names, "mini tank", "super drum", ?flo-bin" and "tote bin", to name but a few.

Jan 1, 1982

By S. Castro, L. Gutierrez

A classification of flotation processes carried out in concentrated electrolyte solutions, e.g., seawater, is proposed using the most obvious features of these processes: low or high content of Mg2+ and Ca2+ ions, pulp ionic strength, and pH. The first distinguishable group is the processes carried out in NaCl/KCl solutions, about 0.5 M in the case of salt flotation of inherently hydrophobic minerals, and at concentrations about 10 times higher in the flotation of potash ores. In the flotation of sulfide ores, such as nickel or copper ores, with xanthate-like collectors, the xanthate collector is apparently not affected by pulp ionic strength and only adjustment of frother may be required. Content of Mg2+ and Ca2+ ions in seawater is the main difference between such systems and fresh water. The presence of these metallic ions can adversely affect flotation in the pH ranges over which these ions hydrolyse. The successful flotation of Cu-Mo ores typically requires depression of pyrite at high pH values achieved with the use of lime. However, in seawater, flotation of Cu-Mo ores requires removal of the hydrolysis products of the Mg2+ and Ca2+ ions or the use of a pyrite depressant that can be effective over the pH ranges that are much below the pH of hydrolysis. Mg2+ and Ca2+ ions also affect flotation of phosphate ores with fatty acids. In this case, the depression mechanism is not caused by precipitating magnesium hydroxides on the mineral surface but by precipitation of collector insoluble salts, and the same ions are responsible for depression in both cases. In the seawater flotation of Cu-Mo sulfide ores and phosphate ores, the practical solution involves either removal of Mg2+ and Ca2+ ions prior to the flotation or complexation with other reagents.

By Håkan Tyni, Jan Björkman, Per-Olaf Samskog, Irving Wigdén

Process automation can provide better utilization of capital investments. Furthermore, it is a necessity for securing the high demands of product quality. In this paper, process automation in underground mining as well as in the beneficiation plant will be discussed. The development of reliable broadband communication systems for real-time transfer of image, audio and data have enabled remotely controlled LHDs and drilling rigs. In the beneficiation plants, model-based expert control systems far on-line dynamic process optimization and control have been installed in unit operations such as grinding, flotation and induration.

Jan 1, 2000

By Silver Miller, William A. Vogely, J. C. Emerick

After location and verification of exploitable mineral resources, mineral development re- quires capital goods, labor, and energy to extract the deposit. In addition, a growing social awareness of the need for a healthy environment re- quires inclusion of environmental burdens to the total costs incurred. This is because mineral development is detrimental to the environment in a number of ways. All mining .operations involve the separation of valuable minerals from the surrounding waste rock, which in turn re- quires permanent disposal of unwanted or un- used materials. Mine overburden, wastes, and tailings are often transferred to peripheral areas where they remain as unsightly features in the natural landscape. Some mine spoils contain harmful or contaminating substances as heavy metal salts or acid forming materials which subsequently are released to the environment. Many types of mining operations handle significant quantities of water during extraction or beneficiation processes. When discharged, the quality of such water often is unsuitable for residential, agricultural, or recreational use. Since mining activity disturbs the natural vegetation in the project area, water may be allowed to transport soil materials into streams, causing erosion and siltation. In particular, surface mining operations disturb the top layers of soils, resulting in losses of productivity for long periods of time. Excavation, transportation, and further processing of large volumes of both ores and waste materials generate substantial quantities of particulate and gaseous emissions, some of which contain metal dusts or compounds of sulfur. Such fugitive and point source emissions can be transported beyond the confines of mineral operations to cause annoyance and damage at more distant locations. Environmental degredation or pollution can be viewed as the alteration of the environment by man through the introduction of materials which represent potential or real hazards to hu- man health, disruption to living resources and ecological systems, impairment to structures or amenity, or interference with socially desired uses of the environment. The significance of environmental degradation is reflected in its effects on a range of receptors, including humans as well as the resources and ecological systems upon which we depend. Pollution also is judged in the social context of damage to environmental structures and amenities. The demand for restoration and maintenance of environmental quality presents the mineral industry with a challenge to successfully man- age discharges and returns to the environment in order to avoid undesirable and harmful consequences. AIR QUALITY Impacts of Mining and Beneficiation Operations Air quality generally is degraded by mining operations through the addition of dust or total suspended particulates (TSP), carbon monoxide (CO), sulfur dioxide (SO2), nitrogen oxides (NOx), and hydrocarbons (HC) to the atmos-

Jan 1, 1985

By O. P. Burghardt

Blast furnaces of high specific throughput capacities producing 10,000 tpd of pig iron or even more, require burden materials which, because of their chemical, physical and metallurgical properties, guarantee such high performances. Meanwhile, it should be generally accepted that for evaluating the quality of iron ore pellets, it is not sufficient to know the chemical analysis and the physical properties, i.e. grain size distribution, cold compression strength and abrasion of the fired pellets. It is indispensable to determine the metallurgical properties indicated by swelling, reduction-softening under load and reducibility, as well as grain disintegration in the low-temperature range in the beginning of reduction. By introducing new test methods, and in the face of the need to meet more strict requirements, pellet producers are being confronted with steadily increasing tasks and problems which require a deepening of our knowledge of the ways and means of making high-quality iron ore pellets.

Jan 1, 1975

By Chee Theng

"It is not surprising that the most popular key takeaway from the Developing Diversity in Mining workshop (see box) held on the first day of the SME Arizona Conference in December was, “Have more parties!”The adage that mining professionals work hard and play hard was clearly demonstrated at the two-day conference in the JW Marriott Tucson Starr Pass Resort & Spa in Tucson, AZ. Nearly 550 participants, some of whom had left behind frigid temperatures and thick parkas in their hometowns, attended a full slate of technical sessions, shared industry experiences and knowledge, reconnected with buddies in the industry, and made strategic new contacts in the conference’s collegial environment, aided by the mild Arizona winter.To start off the technical sessions, John Mansanti, president and chief executive officer of Crystal Peak Minerals and 2017 SME president, entertained a packed lecture room with his keynote lecture on “Tariffs, Embargos, and Cartels ... Oh My! A Perspective on Potash.” Mansanti gave the audience the benefit of his more than 35 years of experience at companies including Barrick Gold, Newmont Mining Corp., Placer Dome, Freeport-McMoRan and Intrepid Potash, where he was senior vice president for operations, technology and strategy. At the luncheon, Justin Cross, general manager of Freeport-Mc- MoRan’s Bagdad operations, spoke on how the role of a leader in mining is transforming from one based on technical expertise to one based on the ability to collaborate, to lead and to adapt to changes in technologies and skill sets, in his talk on “Knowing When to Learn, When to Lead and When to Manage.”"

Feb 1, 2019

By Dean J. Acuff

An overview of new size reduction technology involving the use of two-mass natural frequency vibration applied to a totally enclosed elongated drum. Material moves with a drum-like rotary motion with exposure to constant, aggressive, high frequency agitation for faster reduction and enhanced product quality. A proven, patented design with few moving parts, a vibrating mill drum provides the desirable environmental benefits of a totally enclosed rotary drum but without the same interfacing difficulties. Natural frequency design has reduced energy demand which is met by low horsepower, self-contained, motorized drives to dramatically reduce the cost per ton of finished product.

Jan 1, 1993

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997

By Michele Ashby

The mining industry is facing new risks from peak commodities, the energy and economic crisis and stock market pressures. The Green Mining Industry Initiative is a risk management strategy for the future of the mining industry. Defining the Risks The bad news is peak commodities, energy and economic crisis and stock markets collapsing are the issues that are already hitting everyone?s bottom line and draining the treasuries of every mining company around the world. Higher energy costs are affecting the bottom line more than ever before, which is creating more risk for companies. Mining companies have major land positions around the world and they have major energy needs. Uncontrollable increases in energy costs, increased regulations for diesel fuel emissions and energy intermittencies are costing mining companies more time, money, and man-power, which are cutting into profits and hitting the balance sheet. The good news is, there are practical energy solutions which are off the grid, tried and true methods which can be implemented in a cost-effective manner and will increase profitability and save shareholder values as well as energy security for these companies and their projects. To date, most of the mining resource industry has not yet considered or used other forms of power like clean, sustainable, or alternative energy for their own energy needs. The reasons have primarily been pushback from the mining industry due to beliefs of older technologies in alternative energy, a lack of understanding of the cost advantages long term, and perceptions of environmental relativity.

Jan 1, 2008

By Jörg Weidemann, Peter W. Kuchar, Paul Burgwinkel

The West German Ruhrkohle AG and the engineering company BEDIA have developed an emission control system for diesel engines that is suitable for use in underground coal mining, consisting of a granular catalytic converter and a dry cooling system. Its first ever application was to a diesel mining locomotive. In the catalytic converter the exhaust gases pass over porous, platinum-covered ceramic balls in a double tube, oxidizing CO to CO2. Simultaneously, soot particles in the gases are subjected to afterburning. Laboratory tests carried out by BEDIA and at Aachen University of Technology showed that there was a reduction of over 80% in the CO content of the exhaust gases and over 30% in soot emission. The dry cooling system fulfills all the requirements demanded of exhaust cooling underground and does not have the disadvantages of conventional systems. It needs little maintenance, and it is light and compact. The most important components are a waterjacketed exhaust manifold, a tube and shell heat exchanger, a new type of flame arrestor in a stacked crimped ribbon design and a Venturi diluter. The system has its own thermostatically-controlled cooling circuit to keep the exhaust temperature between 120° C and 150° C, thus effectively preventing the tubes becoming blocked up.

Jan 1, 1989

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000