Search Documents

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By Sanja Zlatanic, Michael P. Della Posta

New York State’s Metropolitan Transportation Authority (MTA) has undertaken the largest transportation project in New York City. The East Side Access Project (ESA) will introduce MTA’s Long Island Rail Road (LIRR) service to the East Side of Manhattan, to a new terminal located beneath the existing, landmark Grand Central Terminal(GCT). Construction of the Manhattan Segment of the project will affect overlying operating facilities of two other MTA entities, Metro-North Railroad (MNR) and New York City Transit (NYCT) and major Midtown Manhattan buildings. The paper describes the evolution of the GCT concept at Manhattan from a shallow alternative proposed by a Major Investment Study (MIS), that would require extensive underpinning of multi-story buildings and have considerable impact on MNR and NYCT operations, to a deep alternative with lesser risk and potential for disruption.

Jan 1, 2001

By M. Churchill, V. R. Degner

Over the past two decades, declining ore body grades and increased operating and construction costs have provided an incentive for the development of progressively larger flotation machines. As a result, the 1.7-2.8 m3 (60-100 cu ft) flotation machine of the 1950's and 1960's is being rapidly replaced by large volume machines. The result has been improved flotation machine specific capacity (tph processed per sq ft of floor space); specific power (hp per tph processed); and process control simplicity. The recent development and satisfactory plant evaluation of the 28 m3 (1000 cu ft) flotation machine allows economic and operating advantages in high tonnage mill applications. Some principles of mechanically induced air flotation and the development of the large 28.3 m3 (1000 cu ft) flotation machine are reviewed here. Performance evaluation in beneficiating metalliferous ores-copper, zinc, and iron-is also given and recently completed plant results provided. Mining lower grade ore bodies results in the need to process increased tonnage in the concentrator. This greater tonnage requires more individual flotation machines, unless individual machine capacity, or cell volume, is increased. As the ore processing rate of the concentrator increases, the benefits of progressively larger individual cells in the flotation section become more significant. The accompanying figure illustrates the advantages of a larger flotation machine. In the figure, the number of machines in the rougher-scavenger section is related to the plant tonnage for three sizes of flotation machine: 8.5 m3 (300 cu ft), 14.2 m3 (500 cu ft), 28.3 m3 (1000 cu ft). The 28.3 m3 (1000 cu ft) flotation machine results in 95 fewer machines, compared to the 8.5 m3 (300 cu ft) machine at 45.4 kt/d (50,000 stpd) feed. The flotation cell reduction is, of course, doubled at a plant production rate of 90.7 kt/d (100,000 stpd). Using fewer flotation machines saves floor space. The 14.2 m3 (500 cu ft) and the 28.3 m3 (1000 cu ft) machines result in a floor area reduction, relative to the 8.5 (300 cu ft) machine requirements, of 134.7 and 418.1 m2 (1450 and 4500 sq ft), respectively, for the 45.4 kt/d (50,000 stpd) rate and 269.4 and 836.1 m2 (2900 and 9000 sq ft), respectively, for the 90.7 kt/d (100,000 stpd) rate. In addition, flotation practice has shown that the "specific power intensity"-power per unit cell volume-is less for increased cell size. This results in a power draw reduction, for the rougher-scavenger circuit, of between 552 and 686 kW (740 and 920 hp) for the 14.2 and 28.3 m3 (500 and 1000 cu ft) machines, respectively, when processing 90.7 kt/d (100,000 stpd). Fewer cells improve machine control and simplify maintenance needs while reducing floor space and power requirements. These are tangible incentives for the development of large flotation machines for high tonnage applications. Flotation Principles The accompanying figure shows how key hydrodynamic regions influence the performance of a mechanically induced air flotation machine. Air is induced into the fluid from the top of the cell, due to the mechanical action of a rotating impeller. The impeller circulates the liquid, or pulp, from the bottom of the cell. The result of these dual flow paths is the mixing of the two fluids and one solid phase in the highly agitated region where physical contact between the air bubbles, and the solid particles to be floated, is accomplished. The particle to be floated is assumed to have a properly prepared hydrophobic surface prior to flotation. Upon leaving the three-phase mixing region, the "floatable particle-air bubble matrix" and

Jan 7, 1982

By K. Adam

Improved environmental performance comprises one of the key objectives of the sustainable development in the mining industry. Within this framework, a research project was undertaken by TVX Hellas, a mixed sulphides producer in northern Greece, in order to develop and evaluate anaerobic wetlands as an alternative method for the treatment of acidic waters originating from old mine areas. The anaerobic treatment using organic substrates, aimed to neutralize the acidity of the mine drainage and remove the dissolved metals, such as Fe, Zn, Mn etc., in the form of insoluble compounds retained within the substrate. The effectiveness of this treatment method, as compared with the conventional neutralization techniques with alkaline additives, extensively used in the mining industry, was assessed based on environmental and economic indicators. The indicators applied included contaminant removal, land take per unit of contaminant removed, effluents quality, remediation of past environmental damage, energy and reagents consumption, capital and operating cost. Based on the above, the applicability of anaerobic wetlands for the treatment of acidic streams originating from old mined areas was concluded.

Jan 1, 2003

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By F. L. Wilke

The prototype of an expert system, designed to assist layout planning of face operations, is presented. By specific combination of knowledge-based and conventional EDP techniques it has been possible to extend the known Kepner-Tregoe method up to the determination of mature layout solutions in difficult planning cases. It has been proven that the presented strategy - which can be applied to any kind of problem with similar structure - is apt to provide efficient EDP support for handling complex mining problems. Such support goes far beyond the purely numeric evaluation of envisaged alternatives.

Jan 1, 1989

By J. T. Gepford, K. A. Prisbrey, T. Scott, M. Spangler

Using neural networks for plant control is challenging. The objective was to show how to make a neural network effective, even with noise, lag times, and unmeasured disturbances in the plant. The procedure was to evaluate the neural network in a laboratory flotation vision system and in a plant refractory gold autoclave system. Although the resulting neural network easily conquered simple laboratory data, the noisy plant data was much more difficult, and adaptive linear models were equally effective. We concluded that the neural network needs support by combining it with other tools found in the best control packages.

Jan 1, 2000

By Andrej Šubelj

The paper tries to determine all which are interested or involved in collecting, evaluating, processing and distributing data on mineral resources, either "economic" or "uneconomic" and for what purposes. It shortly describes some of the most known classification systems, CMMI and UNFC, and their features, and discusses their advantages and weaknesses. Author also tries to define all the properties, a system should have to be declared as "World Code". Perhaps the ,integration of both systems would best accomplish the task and leave the “interest groups" the freedom to use only those parts of the system, they are interested in.

Jan 1, 2002

By Anthony Peach, Lok Home

Introduction Raise boring is the most accepted form of mechanized hard rock boring in the mining industry. It appeared logical to take this mechanization one step further by introducing computers. Atlas Copco Jarva has produced a series of raise boring models that use an integrated computer. The company decided to use electronics and computerization, not for marketing purposes, but to make its equipment more cost-effective. Basis of Cost-Effective Design From the manufacturer's standpoint, it is possible for the equipment owner to reduce the cost of putting in raises by: • Replacing existing components with less expensive components that produce the same results; • Replacing existing components with more expensive components that make the equipment more productive; • Mechanizing equipment to reduce associated labor costs; and • Combining the above. Analysis of a standard raise boring machine (RBM) system showed that little could be done with less expensive components. It appeared, however, that the RBM could be more productive by transmitting more horsepower through the expensive drill string, while being precisely controlled by computers. An RBM system includes a basic machine, drill pipe, accessories, reamer, and cutters. The approximate percentage cost of various components on a standard system capable of boring 300 m (985 ft) long and 3-m-diam (10-ft-diam) aises in medium to hard rock is shown in Table 1. Also shown is the increased cost above standard of the Jarva computerized machine, and the productivity of both. Increased Productivity Penetration is important during the reaming cycle for more productive raise boring. This is possible by increasing the cutter load with constant rpm or increasing the rpm with constant cutter load. To increase thrust and maintain rpm requires increased capacity in the cylinders, drive train, main thrust bearings, drill string, electrical motors, and power units. To increase rpm and maintain cutter load requires only increased capacity in the electrical motors and power units. This is possible because the torque requirement remains constant for a constant thrust load. Only the horsepower increases, proportional to rpm. Since cutter costs are a big factor in raise boring, changes in machine performance must be analyzed to assess the effect on cutter performance. With a standard or typical carbide cutter, as used on raise boring machines, the effects of increased thrust or rpm are shown in Table 2. The assumption is made that the base data is the current rpm and thrust range where the cutters are now operated. It is also assumed one variable is held constant while the other increases. The result of this comparison, approximately, is that a 50% penetration increase can be achieved with little or no increase in cutter cost if rpm is increased 50% and cutter load is maintained constant. A similar 50% penetration increase can be achieved with a 45% increase in cutter cost, if the cutter load is increased by 20% and maintained constant. From an equipment standpoint, it is significantly less expensive to increase rpm 50% than it is to in-

Jan 7, 1984

By James Barker, Jacques Renault, Chris McKee

Previous XRD work by us (McKee, Renault, Barker; 199Oa, 1990b) showed that by using pressed powder briquettes and a peak deconvolution technique, quartz in perlite can be routinely determined at <0.1 wt. %. In the present report, we discuss two additional methods of standardization: 1) chemical determination of quartz in silicate standards and 2) addition of a large amount of quartz to an unknown mixture. The first method applies the concept of mass balance and is sensitive to the analysis of silica and a monitor element. The second minimizes mixing errors; its equation is non-linear and is derived from the two component case with unequal mass absorption coefficients treated by Klug and Alexander (1974).

Jan 1, 1991

By Paul Kents

The Canadian Javelin Limited Cerro Colorado copper-porphyry deposit in Panama, possibly the largest known copper-porphyry, contains between 1350 and 450 meter elevations, drill proven and probable ore in excess of 3.0 billion tons averaging 0.65% of copper equivalent. The deposit is located in the Central Cordillera Range, straddling the Continental Divide at 1500 meter elevation. Local topography is very steep. Accessibility is difficult, all logistics made by helicopter, and only recently a 52 km. road from the Pan-American highway was completed into the area. The deposit was discovered in 1969, and since then 75 shallow exploratory holes and 98 deep holes, the deepest 1340 meters, totalling 45,000 meters have been drilled. Deep holes were drilled at the corners of a regular rectangular 150 meter grid.

Jan 1, 1975

By Stanley N. Watowich

Recently the petroleum market has made us aware that we are indeed global natural resource consumers, and as such, we have become captive to fundamental global resource economics and their attendant vagaries. Global resource supply problems are as old as civilization and mineral exploration one of its important catalysts. On the basis of natural resources empires have been expanded and new frontiers have been developed. Global consumption and production might even be viewed idealistically as a system dedicated to optimizing distribution to the consumer. However, this is not the case. Political instability and increased government polarization make dependency on a global market somewhat insecure. The U.S. must evaluate its domestic mineral re- sources on the basis that all metals are critical and that dependency on even the common and base metals may ultimately weaken our domestic economy and our potential international relationships and could cause critical weaknesses as demonstrated by the petroleum problem. This paper evaluates specifically the Duluth Gabbro Complex, of Northeastern Minnesota, (figure l), as a potential resource of critical and strategic metals. First, a chronology of some of the early exploration, will be followed by more recent intensive company studies and preliminary evaluations of economic feasibility. Lastly, metallurgical data, on some optimum conceptual mining plans will allow metal production data to be compared with an estimate of U.S. domestic needs in 1990. The purpose of this paper is to put into focus the difficulty of converting resources into vitally needed reserves.

Jan 1, 1981

By Joseph R. Hatch

During the past ten years detailed elemental analyses of approximately 8,000 well-documented samples of coils in the United States (including Alaska) have been produced by the U.S. Geological Survey and the various State geological surveys. Examples of data listings include Swanson and others (1976) Gluskoter and others (1977) Hatch, Affolter, and Davis (1979), and Wedge and Hatch (1980). These analyses serve as a basis for evaluating elemental abundances in coals from the various coal province, regions, and fields. When combined with additional geological and geochemical data, some of these analyses give insight into when certain elements were introduced into coals, and which physical and geochemical parameters are most important in determining coal elemental composition.

Jan 1, 1982

By Jack Garrity

The Asarco Mission Complex includes two milling operations around a large open-pit copper mine in southern Arizona. The ore body was discovered in 1953 and the complex has been in operation since 1959. The mills provide the concentration operations of crushing, grinding, flotation and filtering processes involved in processing copper ore. Smelting and other downstream processing are accomplished at other Asarco locations. The mine pays a smelting charge to the smelter, which is seen as a service to the concentrators. The higher the concentration of copper to the smelter, the lower the smelting charge is to the mine.

Jan 1, 1995

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By Paul Soros

A major share of the increase in the energy demands of Ontario province in the next decade will be supplied by bituminous coal mined in the U,S, To be competitive with alternative sources of energy, it is essential that the delivered cost of coal, inclusive of all transportation charges, be kept at a minimum. The Bessemer aid Lake Erie Railroad Company and the Pittsburgh and Conneaut Dock Company are currently building a shiploading terminal at Conneaut, Ohio, to service this tonnage, together with expected increases in coal consumption in the Eastern Lake Erie - Lake Ontario area, (see Fig, 1).

Jan 1, 1965

By William H. Lehr

In recent years, we have witnessed many innovations in the equipment used in handling bulk materials. Not too long ago, any sizeable stockpile of coal or iron ore was attended by one or more material handling bridges. More recently, large stockpiles have been built with mobile equipment of&apos; the earth moving type with bulldozers and front end Loaders being utilized in reclaiming operations. The most recent stocking and reclaiming device is the rotary bucket wheel machine. The early bucket wheel machines built in the United States were developed for the strip mining of coal. We understand that the first American machine was built in the Midwest in 1944. This type of unit was developed in an effort to reduce the cost of removing overburden and to provide satisfactory spoil disposal. As the available coal reserves under shallow cover were exhausted, the cost of removing the deeper overburden with conventional equipment became too great for these operations to continue profitably. The first machine has now been followed by six or seven additional units, the largest of which can handle material at a rate of more than 7000 cubic yards per hour.

Jan 1, 1965

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995