Search Documents

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By D. Hulse

Mineral resource classification is described in both the SME and CIM Standards for Mineral Resource Reporting. The CIM Standard states “… sampling … is sufficient to assume geological and grade or quality continuity between points of observation”, thus is a function of continuity and sample spacing. Continuity can be measured by use of a variogram model, but average sample spacing in three dimensions is more difficult to measure. The declustering algorithms provided with Geostatistics software, are commonly used to weight data for statistical analysis due to the sometimes-irregular spacing between drill holes during exploration. The weights are lower when data is closer, reflecting shared influence between samples, and higher for isolated samples reflecting independence. This paper will discuss the potential to use estimates of the declustering weight as an inverse relative measure for average sample spacing to gauge the confidence of the estimate independent of the single nearest sample. PROBLEM The classification of mineral resources and reserves has long been a combination of science, past experience of the estimator, judgment, and feeling. All of the definitions as presented in the standards of the various countries that participate in CRIRSCO are similar and deal with “sample points sufficiently closely spaced to support confidence in the continuity of …” This has been interpreted as the distance between the block estimated and the nearest sample (or samples). Geostatistics gave us the calculation of the estimation variance of the block, an implicit part of the calculation of weights in Kriging, to account for the confidence in the estimate. More recently, “Kriging Efficiency” has been used, however it is still dependent on the estimation error and responds in a similar fashion to the distance to the closest sample. It is also sensitive to the variogram nugget. Many of these methods result in very low distance/high confidence measures for blocks adjacent to a sample point with confidence decreasing (sometimes rapidly) as the distance to one nearest sample increases. This results in the “spotted dog” phenomenon where individual samples are surrounded by a higher classification near each sample decaying into pattern of decreasing confidence halos. In addition to the visual image of the spots, this raises the more practical problem of mine design when the classification changes between measured, indicated and inferred. This has led to ad hoc methods to classify material within the mining block so all of the stope receives that classification. These manual methods re both labor intensive and subjective. A popular technique is a multiple search method, where the estimator defines a minimum of number of samples from a minimum number of holes within a nested set of search distance that are used to classify estimates. These specified set of increasing distances are usually proportional to the variogram range. While this is generally a good technique and overcomes the spottiness of the closest sample or kriging error, it has certain issues including:

Jan 1, 2019

By M. L. Smith

The U.S. Bureau of Mines Cost Estimating System (CES) has been used for prefeasibility analysis and mine cost engineering since 1978. In the past, prefeasibility analysis with CES has involved the solution of regression equations. The new generation of CES uses an object-oriented expert system in a Windows? environment. Knowledge bases are structured around generic mine models which access shared knowledge bases for system design.

Jan 1, 1994

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By Roger K. McLimans, Venkatramaiah N. Vasudev, Christian Knudsen, Stefan Bernstein, Dirk Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) analyses of sediment samples from coastal regions of Kerala and Tamil Nadu states and the heavy mineral deposits of Chavara, South India, show large lateral differences in the titanium content in ilmenite due to varying degrees of iron leaching. As the depositional environments for the sands with varying degrees of ilmenite alteration are comparable, the cause for the different degree of alteration is due to differences in the primary source of the ilmenite or to differences in the geochemical history of the ilmenite grains during transport from source to deposit. The CCSEM analyses of the heavy mineral fractions show that source of sediments with a high content of titanium-enriched ilmenites, mainly the heavy mineral deposit around Chavara, resides in the khondalite belt of South India (granulite facies metasediments). The less titanium-enriched ilmenites are sourced from other rocks in the area such as the charnokites. Those conclusions are based on the high MgO content in the leached ilmenites, chemical composition of the accompanying garnets (low CaO and high MgO), and the concentration of aluminum-rich minerals in the sands.

Jan 1, 2005

By John E. Edkins

Metal sulfides, chiefly pyrite and mFnor sphalerlte zssociated with che Herrin (No. 6) coal member of the Pennsylvania Carbondale Formation, have been concentrated in a coal refuse deposit in southern Illinois. Oxidation of pyrite has produced highly acid waters with high concentrations of iron, zinc (up to 200 parts per million) and toxic trace elements that have leached downward to a water system perched on glacial drift. Chemical, petrographic, low-temperature ashing and x-ray diffraction were performed on cores. The data show that economic recovery of zinc and other trace metals is unlikely at this site. Energy (coal) recovery at the Superior Washer site is possible if resultant environmental problems are considered in the planning.

Jan 1, 1981

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Pertti Koivistoinen

There are many grinding schools in the mining world, which claim their grinding method to be the best possible - and still the methods concerned vary a great deal. Some of them have multi- stage crushing and only single stage grinding while in others crushing may be nominal, but grinding can be very complicated. - In this presentation firstly the nine most common comminution circuits will be analyzed. Then results from a pilot scale test series will be reviewed, in which nickel ore ground by four different comminution methods was fed to a common flotation treatment.

Jan 1, 1995

By R. M. Guymon, D. D. Lauriski

Safety management can best be described as how each company deals with the control of hazards (human or mechanical) to reduce costly accidents and employee injury caused by accidents. Properly used, effective safety management can mean the difference between being a highly productive, cost-efficient operation or one that "walks the fence," that is less productive with higher product costs. At Utah Power & Light Co's mining division, effective safety management has been used as tool to achieve this difference and remains as the number one priority to maintaining that difference.

Jan 1, 1990

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By D. Wright, J. Samborski

DuPont’s Florida Plant has been mining in northeast Florida and supplying titanium-bearing minerals, zircon and staurolite for over 50years.The site has successfully implemented and “sustained” a land reclamation/habitat enhancement program that goes beyond regulatory requirements and standard industry practices. However, the term sustainability has been used by so many organizations, many with divergent viewpoints, that it is important for a mine to develop its over-all concept and approach to sustainable operation. As a foundation, the outstanding reclamation efforts at DuPont’s mine will be presented followed by a broader look at the overall sustainability strategies and tactics used at the site.

Jan 1, 2004

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By Rod Heath

The Saskatchewan industry has the advantages of an ore body of a size and consistency unmatched anywhere else in the world, and large, efficient mines with production costs that compare favourably with those in other countries. On the minus side, Saskatchewan is remote from most major markets, and producers face a distribution challenge to reach the offshore markets which is the main focus of this presentation. One of the characteristics of the world potash business is that all of the major sources of production are located in the developed areas of the world, while there is no significant production in any of the highly populated developing countries. The major potash producers are located in Canada and the United States, in West Germany, France, Spain and the U.K., in Russia and East Germany, and in Israel and Jordan. There is currently no significant production in any of the countries in Asia (with the exception of Jordan where a plant is currently in the start-up phase), Africa, Latin America or Oceania, and all of these areas must, therefore, import a11 of their potash requirements from the producing countries.

Jan 1, 1985

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993