Search Documents

By Gordon B. French

In order to better understand the relation- ship of underground and surface oil shale processing systems, a block flow chart is presented in Fig. I. From this figure only modified in-situ and Room and Pillar underground mining are currently committed and into the Detailed Design and Construction phases. Figure II illustrates the times required (Federal land site) to bring oil shale operation into production. As this example shows, only those companies having progressed beyond the exploration stage have a chance to obtain oil shale production within the next 10 years. A more detailed breakdown of the oil shale development for those on private lands or having already obtained Federal lease lands is shown in Fig. III for shale oil development (without major regulatory changes).

Jan 1, 1981

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By F. Woodcock, A. R. Laplante

A test to characterize the amount of gravity-recoverable gold (GRG) in an ore is described. Typical GRG results are given and possible uses are discussed. The overall database, which includes 68complete tests, is presented. The ore samples treated had an average GRG content of 63% of the total gold in the sample, with a standard deviation of 20% and a range of 3% to 97%. Both the F8(, of gold and the GRG content at a grind of 100% finer than 850 pm correlate well with the overall GRG content (at 80%finer than 75 pm). The primary use of the test is to determine whether gravity recovery should be used and how. Results can also be used to predict gravity recovery, as many of the ores tested are from plants employing gravity recovery. Gravity-circuit simulation can be used to refine recovery estimates or for optimization studies.

Jan 1, 2000

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By Terry Mudder

Long-term anaerobic biochemical treatment for draindown of residual solutions is a cost-effective way to close a heap-leach pad. This article presents a laboratory evaluation of anaerobic biochemical treatment of cyanide heap-leach pad solutions. The traditional approach to heap-leach pad closure is to rinse the pads with multiple pore volumes of fresh or recycled treated water. The effluent from an initial rinse is often treated and recirculated until the solutions passed through the heap meet the appropriate numeric and narrative water quality standards. Column rinsing tests are completed during project planning to determine the number of pore volumes of fresh or recycled treated water required to rinse the pad to meet long-term closure requirements. A traditional closure plan generally includes provisions to sample the rinse effluent and rinsed solids (the Meteoric Water Mobility, Procedure or USEPA 1312) to verify that chemical requirements are being met.

Jan 1, 1995

By Landy A. Stinnett

Coal mines in the United States are the most productive in the world in terms of efficient labor employment. This is because of an abundance of workable coal beds, large infusions of capital, improved management practices and continuing competitive pressures. The standard unit of measurement for labor productivity is expressed as tons/manshift, although for underground mines, operators often refer to tons per machineshift. Articles written concerning labor productivity generally focus on measurement techniques, safety considerations, application of technology and training. This article will illustrate by example the impact of labor efficiency (or inefficiency) on the ultimate selling price of coal, f.o.b. mine site. During the past several years, the coal industry has seen significant improvement in labor use. Figure 1 shows the trends in productivity for all active mines in the United States from 1985 through 1994. Productivity in 1985 was 20.1 t/manshift (22.1 st/ manshift). This factor has increased almost linearly throughout that period to 37.5 t/manshift (41.2 st/manshift). This is a 7.2% annual compound growth rate.

Jan 1, 1995

By Donald W. Gentry

It appears that the competition for increasingly scarce international mining investment capital will continue among developing countries. Indeed, there is growing evidence this competition may be on the verge of becoming destructive and cutthroat in nature. While this may be viewed as good news by short-term, speculative investors, it could have dangerous repercussions for international minerals producers over the long-term. It seems there has been a continuous parade of traveling foreign delegations touting the virtues of mineral investment in one country or another. These pitches all contain the politically correct key words, such as macro-economic reform, political reform, privatization, liberalization of laws governing mining and related investment incentives, reconciliation of ownership and right-to mine issues, and tax reform specially tailored for the minerals sector. Unfortunately, some of the information being trumpeted is based on plans, concepts or hopes for change rather than actual reforms approved by all necessary governmental entities. In yet other situations, the information provided consists of half-truths at best. Too often, potential minerals investors, faced with metals and minerals prices hovering near their recession lows and the need to offset old, high-cost operations, desperately want to believe all they hear about investment alternatives cast in a near-utopian setting. However, the virtues being proffered for mining investment abroad do not eliminate the need for careful scrutiny of subtle variations of traditional risks associated with foreign investment that can drastically affect the economic viability of mining projects.

Jan 1, 1993

By S. B. Castor

Proceeds from industrial mineral mining in Nevada were approximately equal to those from metal mining during the barite boom in the late 1970s and early 1980s; however, since then the economic importance of industrial minerals has been overshadowed by gold mining (Fig. 1). The total value of industrial minerals mined in Nevada increased by about 60% during the 1980s, reaching an estimated $306 million in 1990 before falling slightly in 1991. The state's most important industrial mineral commodities, in order of estimated value, are aggregate, lithium carbonate, diatomite, lime, cement, gypsum, barite, clay, silica, and magnesia (Fig. 2). Industrial minerals produced on a smaller scale are colemanite, dimension stone, dolomite, perlite, salt, and zeolite. In 1991 industrial mineral commodities other than aggregate were produced at 39 operations in Nevada. Most of these operations are located near the two major metropolitan areas of the state, or along the major transportation routes (Fig. 3).

Jan 1, 1993

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

By Tim Neil, O&apos

Large is the applicable adjective here. The largest hydraulic shovel in the world, the largest copper mine in the world, the largest copper producing company in the world. The O&K RH 300 hydraulic excavator has been put into service to move overburden and mine ore at the Chuquicamata open pit mine of the Chilean state copper mining company, Corporation Nacional de Corbre de Chile (Codelco). A large shovel: Equipped with a 26-m3 (34-yd') rock shovel, the RH 300 is able to fill a 170-t (187-st) truck in three passes with cycle times of 30 seconds. A large mine: At present, the Chuquicamata pit is 4 km (2.5 miles) long, 2 km (1.2 miles) wide, and 520 m (1700 ft) deep from rim to bottom bench. The current 450 kt/d (496,000 stpd) of material mined will increase to 600 kt/d (661,000 stpd) when the expanded production rate is reached in 1989. (Chuqui Expansion details, p. 20). A large mining company: Codelco's total output from its two open pit and three underground copper mines is more than 1.1 Mt/a (1.2 million stpy) of copper. This makes Codelco by far the largest copper producer in the world. It accounts for about 15% of the Western World's copper requirements. Chuquicamata is located in the hot and arid Atacama desert of northern Chile. The mine is located 240 km (150 miles) northeast of the port city of Antofagasta. Mine elevation is 2700 m (8850 ft). Chuquicamata's known reserves of oxide and sulfide ores amount to more than 450 Mt (496 million st) of contained copper. There are also reserves of more then 1.4 Mt (1.5 million st) of contained molybdenum. Originally, Chuquicamata was a rail pit. The shovels loaded rail cars hauled by locis on tracks along the benches. During the 1970s, the rail transport was replaced by truck haulage. Crushing and conveying rock waste in the pit is the latest step in the continuing evolution of more productive and economical methods of materials movement. In 1990, the in-pit crushing plant will be in operation. The waste will be mainly transported out of the pit on belt conveyors rather than trucks. The system will incorporate a 9.6-kt/h (10,600-stph) semi-portable crushing station, a 14-km (8.7-mile) conveyor using 1.8 m (6 ft) wide heavy duty belts, and a tripper-spreader to stack the waste dumps. Since Chuqui went into production in 1915, more than 2.5 Gt (2.8 billion st) of material has been excavated. This includes nearly 1.7 Gt (1.9 billion st) of ore from which some 16.4 Mt (18 million st) of copper has been recovered. The Chuquicamata porphyry type ore body is an altered and fractured intrusive granodiorite or quartz-monzonite porphyry that carries the mineralization. The action of ground water on primary sulfide minerals in geo¬logic time has created oxide ores and a zone of secondary enrich¬ment. The oxides occur above the sulfide zone and are also mixed with the upper parts of the latter. At Chuquicamata, the current grade of 1.5% copper is expected to decline to about 1% by 1995. To maintain metal production at cur¬rent levels, it will be necessary to increase ore production rates by about 50%, as mentioned, to 153

Jan 1, 1988

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

By John A. Folinsbee

Placer Dome Canada owns and operates the Campbell mine and mill at Balmertown, in the north western corner of Ontario. The mine operates at 1.3 kt/d (1,500 stpd). It produced more than 9.3 t/a (300,000 oz/year) of gold during the last three years. Changes to the gravity concentration circuit have resulted in a 10% to 15% increase in gravity recovery. The mill head grade at the Campbell Mill is relatively high, averaging 18.5 g/t (0.54 oz/st) over the total reserve tonnage. During the past several years, the head grade was averaging close to 20 g/t (0.6 oz/st). Before 1994, gravity concentration was achieved by using a combination of conventional mineral jigs and tables. Jig concentrates were upgraded on shaking tables to produce a concentrate, which was refined to bullion. In May 1994, management decided to buy two Knelson CD 760-mm (30-in.) concentrators. The objective was to replace the existing jigs and increase gravity gold recovery by up to 15%. Gravity recovery with jigs averaged between 30% to 35%. Gravity recovery was anticipated to increase to about 50% with the Knelsons.

Jan 1, 1997

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988