Search Documents

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By C. Y. Chen

Public Law 75-87, the Surface :mining Control and Reclamation Act of 1977 (SMCRA), Section 516(b) requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence causing material carnage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, except inn those instances where the mining technology used requires planned subsidence in a predictable and controlled manner . . .?. The Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a Federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features and also summarizes some of the measures which have been used to minimize the possibility of damage to surface structures as a result of subsidence due to underground coal mining.

Jan 1, 1981

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

By C. W. Grate

Cooperative Education is by no means a new idea. The first such program was instituted at the University of Cincinnati in 1906 by the late Dean Herman Schneider with twenty-seven engineering students participating. Today, more than fifty years later, there are in excess of one hundred institutions' with some such program in which thousands of students, are participating in the fields of Liberal Arts, Engineering, and Business Administration. At the same time, according to a conclusion reached during a study of work-study college programs, copyrighted in 1961 by Thomas Alva Edison Foundation, and from which we quote; "We were amazed at the lack of-information about cooperative education among school and college staffs and students, among parents and employers, and on the part of the public generally."

Jan 1, 1963

By F. Calizaya, I. Duckworth

An ore-pass is an underground conduit used to transfer ore from one level of a mine to another. This method of transportation depends on the elevation energy only; therefore, it has very low operating cost. However, two inherent problems may hamper this process: (1) hang-ups of interlocked pieces and (2) a sudden release of trapped air from the ore-pass (belching). These events can create unsafe conditions with the potential for catastrophic consequences. This paper presents a summary of CFD modeling studies that were formulated to investigate the pressure build-up and belching of dust and rock particles from long ore-passes. The models were calibrated against field data collected from an actual ore-pass system and used to predict the airflow-pressure distributions in the mine for various ore feed rates and ore-pass geometries. P.T. Freeport Indonesia’s Grasberg ore-pass system (240,000 tpd capacity) was used for this purpose. This system comprises of four active ore-passes, with each being more than 600 m in vertical length.

Jan 1, 2004

By Paul D. Kovscek, Charles D. Taylor, Edward D. Thimons

When blowing ventilation is used on a mining section, a machine-mounted scrubber is often required to maintain face dust levels below 2 mg/m3. Operation of the scrubber also affects airflow patterns at the face and the dilution of liberated methane. Reductions in scrubber flow can result in increased methane concentrations. During mining, loading of the scrubber filter with dust is likely to reduce airflow. Detecting changes in scrubber flow is difficult, especially with extended cutting, because the machine must be operated from a remote location. Tests were conducted to demonstrate how scrubber airflow could be continuously monitored at a remote location. Three variables, static pressure at the fan inlet, differential pressure across the scrubber filter, and scrubber fan motor current, were continuously monitored while the scrubber filter was incrementally loaded to reduce air flow. The results show that monitoring each variable provided a way for estimating scrubber flow.

Jan 1, 1995

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By R. K. Agarwal

In this paper a simple three-layered medium is considered. A circular hole is centrally located in the intermediate layer. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of [the] intermediate layer and [the] hole diameter. A comparison of stress the distribution and procedures for preparation and testing of [the] model are given. The potential of the technique is outlined.

Jan 1, 1968

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By A. E. J. Gallagher

There are many influences which have a bearing on the economics of industrial minerals production. The purpose of this paper is to discuss briefly three factors which have economic significance in the production of these mineral commodities. The three items of discussion include 1) the nature and relative value of the industrial minerals group, 2) project planning, and 3) market analyses. General aspects of these factors are familiar to most of us. However, an attempt will be made to give some current details regarding each. Also, in reality, project planning and market studies are usually so closely associated that they will be discussed jointly, rather than separately. This will be done by way of examples which show how these two activities actually evolved for two industrial minerals projects.

Jan 1, 1984

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976