Search Documents

By Richard H. De Voto

The McDonald gold project and two satellite gold deposits near Lincoln, MT were discovered in the early 1990s. They contain at least 307.9 t (9.9 million oz) of gold and 933 t (30 million oz)of silver. The McDonald gold deposit alone contains 223.9 t (7.2 million oz) of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $6.10/g ($190/oz). The deposit is predominantly oxidized with no chance of acid production. It can be mined, operated and reclaimed with minimal permanent environmental disturbance other than the creation of an open-pit filled with a fresh-water lake that would support trout.

Jan 1, 2000

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By David S. Young

All pigments and extenders or fillers whether organic or inorganic fall into the following broad general classes: I. Colored II.-White III. Black IV. Metallic A pigment- is any particulate matter that is essentially insoluble and chemically unaffected by the media into which it is dispersed. According to this very broad definition, colored pigments, white pigments, fillers, extenders, and functional pigments would all be included. The particulate size range would also be quite broad ranging from very fine colloidal particles (~0.01µ) to relatively coarse particles (~100.0µ). This broad definition is usually subdivided into more practical divisions which tend to relate the classification of the pigment to its primary function in the system in which it is used. Hence, the word extender implies that its major purpose may be to extend the system.

Jan 1, 1985

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By J. Brendan Mclaughlin, Casimir J. Koshinski, Michael V. Rose, Wolfgang Baum

Mercury contamination is a worldwide problem in the mining, smelting, and refining of gold, silver, and copper. In these areas, mercury may be found as a naturally-occurring material in ores and concentrates, and/or in secondary feedstocks such as leach residues, pyrometallurgical treatment residues, refinery by­products, electrowinning electrodes, autoclave discharge solids, and waste water and acid plant sludges. The United States Environmental Protection Agency (EPA) has designated mercury one of the most harmful heavy metal contaminant in the environment and has implemented regulations that prohibit land disposal of characteristically hazardous wastes containing greater than 0.20 mg/1 TCLP mercury without prior treatment, thus increasing the cost of managing these materials. The presence of mercury in mine, smelter, and refinery by­products and wastes severely decreases, and in some cases eliminates, the ability to recover residual metal values from the contaminated material. The lost revenue associated with this disposal, combined with the increased direct cost of waste treatment, and/or disposal and protecting workers and the environment, can adversely affect overall profitability. The safe, efficient, and economical removal of mercury from gold, silver, and copper mining by-products requires a treatment process that is capable of liberating the mercury from the wide variety of compounds and matrices in which it may be contained, reducing the mercury content in the matrix to desired levels, and recovering the mercury in pure saleable form, without producing any secondary solid, liquid, or gaseous wastes. This paper reviews results from commercial operations and pilot scale tests using a thermal process owned and operated by Mercury Recovery Services, Inc. (MRS) to remove and recover mercury from copper acid plant blowdown sludge, Merrill­Crowe precipitate from gold/silver mining operations, and Cottrell and salt slag dusts from a precious metals refinery.

Jan 1, 1997

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany's dominance of the world's dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999

By Antonio Pineda, Roger K. McLimans, Felicity E. Lloyd

lmenite is a primary ore feed to the DuPont chloride process for the manufacture of titanium diox-ide pigment. We seek to determine ilmenite geochemistry as a function of original source and as-certain which ilmenites have chemistry most amenable to upgrading via iron-leaching (leucoxenization) and that have favorable, with respect to pigment manufacture, trace element content. Ilmenite geochemistry is a function of its primary origin and of subsequent alteration. Heavy mineral sand deposits may contain ilmenite from one or several dominant source rock(s). In addition, ilmenite may alter in the weathering environment, changing the major element compo-sition (iron-leaching) and certain of the minor element content. A primary objective is to classify ilmenites in relation to origin in order to fingerprint source rocks in provenance determination. The changes in trace element chemistry during alteration are also investigated. A “decision tree” is developed to classify ilmenite types and source rock origins. Ultimately, with those methods and by amassing a database of ilmenite types from worldwide locations, it should prove possible to determine ilmenites (and their sources) more susceptible to iron leaching in the weathering en-vironment. Such ilmenites, enhanced in their titanium content, are the preferred ore targets. The method used is electron microprobe analyses at elevated conditions of voltage, cur-rent, and counting time to enable higher precision. In-situ ilmenites from igneous, metamorphic, and altered rocks (saprolites) are analyzed. Initial foci for sedimentary ilmenites are restricted provenance (approaching monogenetic, examples from Spain, Portugal) and polygenetic prove-nance (Denmark). Altered ilmenites, including the DuPont Florida ore, are used to characterize the chemistry of leucoxenization. Trace element concentration, detectability, and cost considera-tion, led to focus on Mn, Mg, V, Cr, and Nb to develop a classification scheme validated by dis-criminant analysis and “classification-regression trees”. Results show a high degree of success for restricted provenance study and an acceptable one for polygenetic provenance.

Jan 1, 2005

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By V. McLemore, N. Dunbar, K. Donahue

There are three principle lines of evidence that indicate the clay minerals found in the Goathill North (GHN) rock pile at the Molycorp mine are predominantly a product of hydrothermal alteration, not weathering. The unweathered drill core and samples from GHN have similar types and abundances of clay-mineral groups based on XRD analysis. Chemical analyses from the electron microprobe reveal similar chemical compositions for the hydrothermal alteration clays in drill-core samples and clays found in the rock pile. Textural evidence gathered from petrographic and microprobe examination also suggests a hydrothermal origin for clay minerals.

Jan 1, 2007

By Brian Flintoff

SCOTT COULTER: Our second speaker today is Brian Flintoff. Brian graduated from the University of Alberta in 1973 with a master's of science degree and worked as a project metallurgist at Brenda Mines until 1977. He returned to the University of Alberta in late 1977 to work on his Ph.D. and later joined the faculty of engineering in 1980, leaving in 1988 to rejoin Brenda in the newly formed process technology division. In 1998 he left Svedala-Brenda to take a position with Simons International's newly formed enterprise development services group. His topic today is "People: Reduce, Reuse, and Recycle." INTRODUCTION BRIAN FLINTOFF: Historically, the mining industry has relied on the people within a corporation to get things done. The culture of most companies was one of a slow but sure development of people, processes, equipment, and technology. Many of the larger companies supported in-house engineering and research organizations. However, the metal market pressures of the 1980s and the emergence of the global economy in the late '80s and early '90s put enormous financial pressures on the industry. As the old adage says, "necessity is the mother of invention," and the mining industry, like many others, has undergone a transformation. A cornerstone element of the transformation was the downsizing (or right-sizing) that was calculated to "trim the fat" from the capital and operating budgets. The goal was and is to find the highest sustainable operating profit.' While I'm sure one can find examples of losers (e.g., those who can be classified as suffering from corporate anorexia or institutional Alzheimer's) in such business reengineering efforts, there is little doubt that, on the whole, the transformation has been successful. The reality that now faces mill management is "How to do more with less?" At the risk of oversimplifying, one can look at this on two levels:

Jan 1, 1998

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013