Search Documents

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By W. Kemp Wait

Electronic ore sorting is a coarse particle beneliciating process which performs a function which in the past was primarily achieved through the use of hand picking belts. Photometric ore sorting is capable of separating waste from mineral bearing rock having a distinct difference in surface light reflectance levels. This type of ore sorter can be applied to gold and silver ores which are contained in quartz veining. Photometric ore sorting has been used at gold mines in South Africa as well as the Black Pinc silver mine in Montana. A new ore sorter has recently been developed with precious metal ores in mind. This ore sorter is capable of sorting ores on both photometric and conductivity sensing parameters. The first production machine has been installed at a gold mine near Beardmore, Ontario and currently is being used to process low grade waste dumps.

Jan 1, 1998

By James A. Madonna

Information gathered while studying geological parameters that govern fine gold deposition in the a1luvial environment can be applied to the technological development and selection of fine gold recovery systems. It is recognized that substantial gold losses occur in the minus 1.5 mn (minus 12 mesh) fraction using conventional sluicing systems. Within the past two decades much attention has been given the design and efficiency of these thick bed concentrators. Studies and comparisons drew information from several foreign and domestic placer operations. These studies concentrated on: 1) the physical and chemical properties of alluvial gold 2) the parameters that control fine gold deposition 3) the geometrical form, components and general working structure of conventional sluicing systems 4) the physical properties which contribute to the overall efficiency of a sluice system 5) the comparison of three major styles of conventional sluicing systems. A dramatic improvement regarding fine gold recovery and water quality was observed when using modern multiple-channel sluicing systems in place of conventional single-channel sluicing systems.

Jan 1, 1988

By V. R. Degner

The minerals industry trend toward very flotation machines, exceeding 10 m3, began in the late 1960's and responds to the continuing desire to achieve better plant economics through improved plant floor-space utilization, power requirements, and operational /maintenance manpower heeds. In general, as process design tonnage increases, the benefits of the larger flotation machine becomes more evident. The development of the larger flotation machine can be distingushed from earlier, smaller, machines in demanding a rational "scale-up" procedure to guide the basic design, thereby producing a machine prototype capable of satisfactory-operational evaluation at minimum cost. Proven flotation machine "hydrodynamic" scale-up consideration, successfully applied in the development of both the WEMCO No. 164 (28.3 m3) and No. 190 (42.5 m3) machine will be reviewed, and the resulting economic benefits of large flotation machines in high tonnage applications will be summarized.

Jan 1, 1985

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By J. D. Grace

[Screening by centrifugal force is an unique, subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon, gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey materiel along the screen, is the SYMONS V-Screen. This screen was designed by Loren Symons, a member of the family that has contributed so much to the metallic and non-metallic mineral processing industries. Among Symons' other outstanding contribution to these industries are the original Cone Crusher which revolutionized reduction crushing practice, the first high-speed horizontal vibrating screen, the original Rod Deck Screen, and one of the earliest vibrating Bar Grizzlies.]

Jan 1, 1965

By D. D. Potter

ABSTRACT OF ORAL PRESENTATION Extraordinary conditions are often encountered when designing large blasts for in situ mining methods and spatial or innovation techniques are sometimes required. Some of the considerations in designing these large blasts will be discussed with emphasis on those factors that concern powder factor, rock movement and fragmentation. Sources of basic data will be described, along with some of the methods for obtaining these data.

Jan 1, 1977

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By Theodore H. Eyde

In the southwest porphyry copper province, the virgin prospect with good copper mineralization cropping out has disappeared. Future discoveries will require an increasingly sophisticated arsenal of exploration techniques and concepts. One of the latter, stratigraphic analysis, is a technique which is often overlooked. A surprising number of exploration geologists still think of porphyry copper deposits as occurring wholly within intrusive bodies such as quartz monzonite or granodiorite. Disseminated copper mineralization, though genetically related to intrusive rocks, can occur within both the intrusive and the intruded rocks. At present, as much as 30% of the total copper produced from disseminated copper deposits in the Southwest originate from the intruded rocks rather than the intrusive. George M. Schwartz, in "Geology of the Porphyry Copper Deposits of Southwestern North America" points out that the host rocks at porphyry copper deposits include such diverse rock types as diabase, granite, limestone, dolomite, quartzite, skern, sericite schista, and others in addition to the more common monzonite, quartz-monzonite, and diorite porphyrys. Therefore, a porphyry copper can be defined as a disseminated copper deposit occurring either in or adjacent to a granitic-monzonitic-dioritic intrusive which can be exploited using bulk. mining techniques. The original definition of porphyry was originally applied to the early producers, such as Inspiration, Bingham, and Ajo, in which the copper mineralization occurred principally within the intrusive. A review of the geologic literature describing the porphyry geologic

Jan 1, 1971

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By Gary E. Geiger

laboratory studies were performed to assess the calcium carbonate inhibition performance of phsophonates and polymeric dispersants at high hardness and high pH conditions. Based on the results of these studies, a new calcium carbonate treatment program was developed that shows excellent Inhibition characteristics and Is not sensitive to calcium hardness.

Jan 1, 1998

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By W. D. Eddy

Topaz is a fluorine-bearing aluminosilicate mineral of the kyanite-sillimanite group. The formula has been given as Al2SiO4(F,OH)2, [Al(F, OH)]2SiO4, or 2Al2O3?2Al(F, OH)3SiO2. Topaz is generally considered a semiprecious-to-precious gem mineral, but it is a fairly common minor constituent of granites. In 1937 the U.s. Geological Survey reported an occurrence of massive topaz in the 3 Brewer gold mine, Chesterfield County, S.C. Over the next 8 years considerable research was done on topaz to establish its properties and to determine possible end uses The first reported shipment of ore was in 1939 Peak production was reached in 194412, and output then began declining until the mine closed in 194913? During World War II topaz was used in refractories, as a flux in steel mills, and in the manufacture of borosilicate glass 14. The main advantage of using topaz over kyanite and sillimanite in refractory use was that calcined topaz converted to over 95 percent mullite (3A1203 .2Si02) while calcined kyanite or sillimanite contained only 88 percent mullite15. However, a major draw-back to utilization of topaz is the evolution of fluorides during calcination. In 1973 the Geological Survey reported that topaz occurred in probable commercial quantities in at least two domestic locationsl6: the Brewer area of South Carolina and a location in Colorado. The literature also indicated that progress had been made in controlling fluorine-bearing fumes. This research has progressed to the state where valuable fluorine compounds are being recovered on a commercial scale 17. Thus, a major obstacle to utilization of topaz appears to have been resolved. The Bureau of Mines under its program of advancing minerals technology initiated a project to study techniques for the concentration of topaz from disseminated materials. The objective of the study was to determine those techniques that would be used to produce topaz concentrates that could be utilized as a source of fluorine and mullite.

Jan 1, 1977