Search Documents

By M. G. Ayat, B. C. Scott

J. Dasher Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title. reply by M. G. Ayat The first and the last criticism of this paper is that the work is not pertinent to the title. Anybody who reads this article will immediately realize that the work describes the breakage of coal particles to finer sizes in coal slurry pipes and pumps. If this is so, why not title the work "Degradation process in coal slurry pipelines"? What could be more pertinent to this title than the investigation concerning the degradation phenomenon of coal particles in a pipe carrying a coal slurry? Mr. Dasher complains that he does not understand the meaning of the term "increasingly smaller size." The first sentence of this article defines the degradation process as "the breakage of coal particles to increasingly finer sizes." The term "increasingly finer sizes" here means successive breakage of a fine particle to finer and finer sizes. According to Hukki (Hukki, 1975), the probability of breakage is high for large particles and rapidly diminished for fine sizes. We apologize for being brief about some of these definitions. The degradation process, breakage of particles to increasingly finer sizes, is so widespread in the mineral industry that we did not feel it necessary to bore the reader with lengthy definitions of some simple terms. Mr. Dasher states that the coals examined and their original size consist are unidentified. Please look at Table I and Table 2 in the paper again where you will find the original size consist of the coals examined and their full specifications. We only named the coals A, B, C, D, and E to avoid identifying the coal seams that were more susceptible to degradation. Not identifying the name of the wet screening device used in this work has also been criticized. In our opinion, wet screening operation is such a routine and standard procedure that naming the device by which the screening is performed would serve no purpose but to promote a sales approach. This was not our intention. We did not conclude that the correlation between the degradation process and Hardgrove Grindability Index is hard to establish as Mr. Dasher writes in his letter. We stated, not concluded, that "It is reasonable to assume that some relationship between the extent of degradation and its physical properties, such as Hardgrove Grindability Index, does exist. However, any definite correlation is difficult to establish." This statement is based on other researchers work, which are clearly referenced in the article. The conclusions of this paper were based solely on the findings of the experimental work. As for the theory of comminution that Mr. Dasher asks, we would like to refer him to some basic comminution books and articles where various theories are clearly described. For example, Hukki (Hukki, R.T.,"The Principles of Comminution; An Analytical Summary," Eng. Min. 176, 106, 1975) suggests that the relationship between energy and particle size is a composite form of three laws (Bond's law, Kick's law, and Rittinger's law). A comprehensive analysis of coal breakage processes is also performed by Broadbent and Callcott (S.R. Broadbent, and T.G. Callcott, "Coal Breakage Processes, I. - A New Analysis of Coal Breakage Processes;" and "Coal Breakage Processes, II. - A Matrix Representation of Breakage," Journal of the Institute of Fuel, pp. 524-539, December 1956). These and many other relevant publications explain the relationship between the particle size and energy much better that what can be said in this short reply. We will, however, agree with Mr. Dasher on one particular point. We, too, believe that if the investigation concerning the degradation process in coal slurry pipeline were to be pursued further, one could choose to determine one or more of the variables available in the process, such as discharge pressure, power consumption, percent solid, pipe diameter, etc.

Jan 1, 1989

By John T. Awald

The efficiency of search for porphyry copper and molybdenum deposits can be greatly increased. A model exploration system is here presented to show how geologic literature data and field surveys can be aided by modern statistical and computer methods. Assuming that major ore deposits occur in clusters, it is possible to evaluate rapidly large areas at modest cost and with minimum investment risk. An example of the success of these methods is given. Clusters of mine density and metal production covering the State of Nevada were plotted and machine contoured. Selection of a 47,300 square-mile area on the Nevada-California border was made. Within this area, detailed analyses were performed, and a 3000 square-mile site was picked for subsequent field examination. To initiate efficiently the field work, 81 stream sediment geochemical samples were collected and analyzed for copper, zinc, and molybdenum. These data established local variance and necessary statistical controls. Following this, a total of 151 geochemical samples were used to survey the 3000 square-mile area. Computer contouring of results directed attention to specific target areas for detailed geologic analysis, property acquisition and drilling. A total of 22 copper-zinc and molybdenum anomalies were identified. Four of these were recommended for further exploration. To date, two have been acquired and drilled and preliminary ore reserve and financial analysis have been made on one. The estimated cost and time for the regional exploration phases leading to these targets were thirty man-weeks and $16,000.

Jan 1, 1973

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By C. L. Karr

Researchers at the University of Alabama are investigating artificial intelligence based computer models of mineral processing systems. Two approaches have been found to be particularly effective in developing data-driven computer models. The first approach employs neural networks which are computational paradigms based on the mechanics of the human brain. They are able to extract the basic relationships between input and output variables from large data sets. The second approach combines fuzzy mathematics with genetic algorithms to produce an adaptive modeling system. Fuzzy mathematics provide computers with the capability of manipulating abstract concepts like those which humans use so effectively in decision making. Genetic algorithms are search algorithms that mimic evolutionary processes apparent in nature. Together, these two techniques can be used to produce an effective modeling system. In this paper, the two approaches to modeling are compared and contrasted with respect to accuracy and computational time while used to model three mineral processing systems: (1) a grinding circuit, (2) a hydrocyclone separator, and (3) a flotation circuit.

Jan 1, 1997

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball, Katherine Walton-Day

The solute-transport model OTIS and the reactive solute-transport model OTEQ were used to simulate geochemical conditions in Cement Creek, a tributary to the Anirnas River in Colorado. OTIS was used to depict instream zinc concentrations, and to simulate the effects of two remediation scenarios on zinc concentrations at the mouth of Cement Creek. These simulations do not account for effects of changing stream pH on metal concentrations. Preliminary simulations using OTEQ to account for instream pH changes were unsuccessful due to the spatial nature of mixing processes, and insufficient information about the thermodynamic properties of precipitates forming in mixing zones.

Jan 1, 2000

Man’s search beneath the earth for minerals has always required light, and the devices used to provide illumination have been both innovative and unusual —from stone vessels holding fat and a wick of grass or fiber to a shower of sparks produced by a thin steel disc. While the date when lamps were first used in mines is unknown, Greek and Roman records from 3000 BC definitely mention their use in underground mines. Early Remans most likely used a lamp similar to the one depicted at right. Over the ages, various types of devicives and methods of illumination have been tried and used. One interesting scheme for underground light was to reflect sunlight down the shaft and along drifts using mirrors or other reflective materials. Bunches of resinous wood were also used for underground lighting in many parts of England. In the mid-18th century, the speding mill was developed in England. It worked by rapidly turning a thin steel disc against a flint, causing a shower of sparks to appear. The light produced was uncertain, highly variable, and unsafe in gaseous environments. In Europe, an open pan-type hanging oil lamp was developed and used in some operations in the 1700s. This type of lamp had one opening for a wick and a second opening for refilling the oil reservoir. The lamps were embellished with goad luck charms – a good luck rooster was used in many parts of Europe while a frog and “gluck-auf” were used in Germany. These lamps were introduced in Mexican mines, and a few have found their way into the southwest US. By 1850, a small wick lamp known as the lard-oil lamp, which resembled a tea pot, was invented in Scotland. These lamps were fueled with grease from a packing house –lard, bacon grease, or tallow. Whale oil was also used. Many improvements were made on these lamps, such as the use of windshields and the attachment of miners’ candle-holdm to support the lamp. While these lamps were handy and inexpensive to operate, they were dangerous because their large flame could ignite support timbers or other flammable materials. Miners from the United Kingdom brought this type of lamp into the US. Domestic producers of oil wick lamps were primarily located in Hazleton, PA; What Cheer, IA; Pittsburgh, PA; and Frostburg, IN. The first patent for an oil wick lamp was granted to W. Seybold of McKeesport, PA. Incidentally, these lamps were advertised in a 1903 Sears-Roebuck catalog for 10 cents apiece. Oil wick

Jan 7, 1980

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

By John W. Kelse

What happens when the skull and crossbones goes on a product? In the case of cancer warnings, the consequences can be severe. If the label contains the term "lung carcinogen", you might expect to compensate a lot of smokers, meet a lot of expensive lawyers, be counseled by equally expensive consultants and pay sharply elevated insurance premiums, if you are able to obtain coverage at all. At the extreme, you may face plant shutdowns, job losses or even Chapter 11 bankruptcy. Regardless of how you fare, you are likely to learn some very disconcerting things about the risk evaluation and regulatory system which required you to label in the first place. If a particular material or product does pose a health risk, you are obliged both legally and morally to warn those potentially exposed. Once that warning appears on the label, however, the consequences are often beyond your control. You and your embattled product become part of a legal/regulatory system which has a life of its own. Therefore, the issue of health labeling is not so much whether one warns but rather whether the warning itself is justified and the reasonableness of what happens afterwards. It is this matter of justification and reasonableness, particularly of cancer warnings, which this paper addresses. Until, as they say, your ox has been gored, we tend to believe that risk is determined by the best available technology and expertise We expect that risk evaluators appreciate the ramifications of their work and place things in proper perspective; that risk has been appropriately demonstrated before it is publicized and regulated; that the time-honored concept of prudence, to err on the side of safety, has not been excessively stretched. Unfortunately, the risk evaluation process is rarely, if ever, this

Jan 1, 1991

By G. M. Swinkels

It is generally accepted, that oxygen is a necessary reagent for the flotation of galena with xanthate. Recent measurements have shown (1) that under plant conditions oxygen may be in a short supply to the extent that it limits the rate of flotation. Thus, it becomes important to define the exact role of oxygen and establish a model for the rational design and control of flotation separations, involving oxygen as a reagent. All theories or, the flotation of galena assign oxygen the role of an oxidant. However, they disagree on a number of questions: 1) Is the galena or the xanthate being oxidized? 2) Is a lead dixanthate or dixanthogen the actual collector? 3) Is the oxidation process in which oxygen participates of a chemical or an electrochemical nature? The last question arises from the observation (2) that an anodic bias as well as oxygen will make a galena surface hydrophobic in the presence of xanthate. Theories which are based an the premise that the influence of oxygen is of an electrochemical nature offer elegant models of galena flotation. However, full advantage has not been taken of available electrochemical techniques to discriminate between theories and this is the area towards which this research has been directed (3).

Jan 1, 1970

By William Gleason

"Sometimes it’s the smallest things that make the biggest difference. In the world of mining, erosion can lead to small cracks, which can then lead to bigger problems that, over time, can eventually lead to a catastrophic event. However, when managed correctly, as in the case of the Manefey Slide at the Bingham Canyon Mine in Utah, the damage can be minimized.Numerous industry conferences, technical papers, studies and resources are dedicated to these issues each year, but what is sometimes overlooked is how the erosion of personal ethics can also have life-changing effects.At the 2019 SME Minnesota Conference, April 15-17 in Duluth, MN, two inmates serving their respective prison sentences at the U.S. Federal Prison Camp in Duluth spoke to the conference about how small cracks in their ethical foundations grew over time, eventually leading each man to his new address at the minimum-security facility.The men’s full names were not released and they were introduced as Jeff and Tony. Other than the matching green uniforms, both middle-aged men could have fit in with the rest of the crowd. They are well-educated and articulate whose career paths eroded thanks to greed and careless decisions.Tony, a licensed professional engineer, enjoyed a successful career working in contract oversight for the U.S. Department of Defense. Jeff is a former senior vice president of investments who ran a well-respected investment management team. Both spoke openly about the mistakes they made and emphasized that their crimes were not flagrant violations of the black and white rules but grew from ethical violations that live in the gray area between black and white, and right and wrong.Working in contract oversight for the U.S. Department of Defense (DOD), Tony said he was befriended by a wealthy man who was generous with his money. As Tony told it, a few meals with this man led to a few trips to casinos and eventually to gifts of money. The donor did not ask for anything in return, and at the time, Tony said he did not think that he was doing anything wrong. He admits now that the perception of a high-ranking officer in the DOD accepting gifts is not a good one, as it could be construed as the donor might have been trying to gain favor for future contracts; which is how it was presented in court by the prosecution team."

Jun 1, 2019

By Robert D. Hansen, Richard R. Klimpel

INTRODUCTION A very important factor in froth flotation is the use of surface-active chemicals to form a froth in which minerals or coals are retained, thus allowing for valuable component enrichment. In coal flotation reagents (frothers) specifically designed to provide an efficient froth are employed. It is this group of chemicals that will be the primary emphasis of this paper. Despite the importance of frothers, surprisingly little systematic scientific work has been performed with the goal of quantifying frother mechanisms and the influence of particles on froth stability. Based on direct experimental observations in both batch laboratory and continuous large-scale flotation cells, the use of a frother significantly increases first, the possibility of a particle- bubble contact, and second, the efficiency of sticking after such a contact. Thus, a major role of a frother is to significantly increase the rate of flotation. This rate modification by a surface-active agent occurs through several observable mechanisms including the formation of a froth of relatively consistent character (bubble size and bubble density) under a variety of operational conditions, an increase in the ability to disperse air in the flotation cell, a reduction in the rate of coalescence of individual bubbles in the cell, and a decrease in the rate of bubble rise to the pulp surface. It will not be the intention of this paper to exhaustively list all frother accomplishments related to research, development and use in coal flotation. Rather, the authors will attempt, based on their experience, to present a technology overview of the role of frothers in the chemistry of flotation as successfully practiced at the industrial level. A very useful framework for flotation is the concept suggested by Klimpel (1984, 1984a) of viewing flotation as a system consisting of three major components: chemistry, equipment and operating variables. This is illustrated in Figure 1. A major point of this figure is that flotation is a highly interactive system with many technical and economic combinations of component settings available to operators to achieve a given goal. Sometimes simultaneously changing various component settings will reinforce a particular attribute. Also various component settings can cancel or counteract each other if changes are not chosen wisely. Thus, coal flotation must be viewed by the plant operator as a complex system with the economic/technical optimization of a given flotation process being directly related to the operator's knowledge of how his particular flotation system behaves as a function of the major control variables he has at his disposal. Typical important component settings in coal flotation are collector dosage, frother type and dosage, air flow rate, feed rate, particle size, pulp density, and the surface oxidation conditions of the coal. Because of the above complexities, it is sometimes assumed (especially in laboratory studies) that the choice of frother type and dosage is not as crucial as some of the other factors such as collector type and dosage (e.g., Leja, 1982). Detailed plant level testing of all of the factors of Figure 1 performed in recent years, Klimpel (1980, 1980a, 1982, 1984, 1984a), Hansen (19861, Klimpel, Hansen and Meyer (1982), simply do not support this assumption. The above testing has shown rather clearly that certain frother chemical structures consistently exhibit predictable performance characteristics in both mineral and coal flotation. In addition, significant changes in both rate and recovery can be expected. In the remaining sections of this paper, the following topics will be covered: requirements of chemicals capable of use as frothers, types of chemicals used commercially as frothers, some general performance characteristics of existing commercial frothers, and recent work in developing new frother chemical structures.

Jan 1, 1986

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada's Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval's exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval's 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By H. Boyd

Fluid energy grinding, or jet pulverization, refers to the process of entraining solid particles in high velocity gaseous or vaporous streams and reducing their size by impact and attrition against other particles or some sort of target. Since all desired size reduction is not achieved in one pass through the zone where energy is applied, some form of classification is necessary to return oversize particles to the grinding zone for further size reduction. Applications Fluid energy mills have normally been used to produce products where the particle size is basically finer than 325 mesh. Products having particle size distributions with a maximum size of 4 or 5 µm, and with a high percentage finer than I µm, can be produced using fluid energy mills. More recently, some fluid energy grinding units have been applied economically to produce ground products with 1 or 2% coarser than 200 mesh. It is also possible to consider usage of a jet-pulverizing zone, without the usual integrated air classi¬fier, operated either in open circuit or in conjunction with a screen. Feed sizes to be delivered to the fluid energy mill depend on the material involved, the type of jet pulverizer used, the finished product size requirement, and the upstream process. In some units feed sizes up to l in. or larger can be accepted, but practical economics usually require the starting material to be -4 mesh or smaller and some pulverizers are typically fed at 20 mesh top size. It is not unusual to find feed materials at essentially -325 mesh when extremely fine products are needed, since capacities are improved with finer feeds. Conventionally the fluid energy grinding process has been used for relatively soft and nonabrasive materials. This includes very low¬melting-point and temperature-sensitive materials or coatings, since there is no measurable temperature rise during fluid energy milling. More recently, however, jet pulverizers are being used on highly abra¬sive materials such as silica, feldspar, glass, zircon, calcined alumina, coke, boron carbide, and similar materials. Since the primary energy application is by impact of particles against themselves, there is a low rate of wear resulting in a small amount of product contamination and in low maintenance costs. Usually the fluid energy pulverizer produces a more narrow particle size distribution than other mills provide, and this is useful where such a requirement exists. It is possible, within limits, to adjust classifi¬cation and other functions of the overall fluid energy system to vary the particle size distribution curve and thereby approach the broader distribution obtained from other grinding methods. By controlling the temperature, composition, and humidity of the fluid used, it is possible to incorporate other functions with the size-reduction process. These include drying or adding moisture, coating, mixing and blend¬ing, and even oxidation or reduction and other chemical reactions or their inhibition. The finished product is discharged in the fluid stream and is conveyed pneumatically to the desired point, where a suitable dust collector must be provided. Operation and Mechanical Features One of the earliest fluid energy mills is the Micronizer now manu¬factured by the Sturtevant Mill Co. Similar units are also manufac¬tured by Jet Pulverizer Co. and others. As shown in Fig. 81, the micronizer consists of a shallow circular grinding chamber with noz¬zles arranged at the outer periphery to discharge tangentially inward. Fluid (usually compressed air or superheated steam) is provided to the nozzles from a manifold at pressures normally in the range of 100-150 psig and at temperatures up to 800°F or higher, depending on the raw material, required results, and economic factors. The com¬pressible fluid expands to high velocity through the nozzles and gener¬ates a spiral flow pattern in the grinding chamber, and discharges

Jan 1, 1985

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

By S. Srinivasan

Traditional pit optimization techniques cannot take account of the requirement to blend ore in order to produce a saleable product, as is the case for iron ore, coal, limestone and other industrial minerals. Various techniques are proposed to overcome the deficiencies, many of which have been tested. The techniques in general involve the combined application of pit optimization and blend optimization techniques.

Jan 1, 1996

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022