Search Documents

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By C. B. Manula

A method for the feasibility assessment of open-pit operations using conventional shovel/ truck systems to mine steeply pitched coal seams has been applied at The Pennsylvania State University. Three computer models were developed for the analysis: a geology and reserves model (GEOL), an open-pit materials handling simulator (OPMHS), and a cash flow model (CASH) (Manula, Albert, and Burgos, 1976). GEOL provides the basic mining data; OPMHS simulates shovel/truck performance related to pit profiles and average mining locations to provide productivity rates needed to size the system; and CASH provides either a selling price or rate of return (ROR) for the product. The general flow of information generated by these models is shown in Fig. 1. Since the ratio of overburden-extracted to coal-produced places a definite economic limit upon a mining venture, geological data must be analyzed with the least possible manual effort to minimize computational errors. This is especially true if the property contains several seams that are steeply pitched. In this situation, a computerized analysis is by far the most efficient and effective method to determine coal reserves and waste tonnage. This chapter describes the reserve model developed at Penn State and provides an example to demonstrate its application.

Jan 1, 1979

By Andrzej M. Wala

The purpose of this paper is to describe a data-acquisition system for mine ventilation surveys that was developed by the author. The system is composed of "off-the- shelf" components integrated through a custom- designed software package to form a user- friendly data acquisition system capable of operating as an unmanned base station or as an operator-triggered roving station. To demonstrate the applicability of the developed system, the author will present data collected during an experimental ventilation survey, which was performed in one of the underground coal mines of eastern Kentucky.

Jan 1, 1993

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

By Gary S. Brierley, John W. Critchfield

This paper is a case history of a subsurface exploration program conducted for a system of sewer tunnels in upstate New York. The focus of the discussion is a non-technical outline of how the exploration process was organized to efficiently produce a large body of geological and geotechnical data. A brief description of the project and geological setting is provided, the scope of the exploration program is summarized, the logistics of collecting, processing and reporting subsurface data is outlined, and recommendations for management of explorations applicable to any rock tunnel are provided.

Jan 1, 1983

By Q. Xu

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactant was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1991

By B. Fitch, E. J. Roberts

Definitions and Terminology Classification is defined within this section as the separation of solid particles into size or weight fractions or classes by differential settling through a fluid. It is usually thought of as a size separation, but is actually made on the basis of particle settling rate, and so is affected by any variations in particle density and shape. The fluid may be liquid (wet classification) or gas (dry or air classification). This section will treat only wet classification. There are two basic types of classification; pool and hydraulic. In pool classification a suspension of feed particles is fed into and out of a pool of some kind at such a rate that only part of them¬ the coarser and faster-settling part-has time to settle out. The remain¬der overflows as fines. In hydraulic classification the feed suspension is introduced into or above one or more columns or pockets through which water is rising at a controlled velocity. Coarse particles subside through the pockets and are removed through spigots. Those which settle slower than the rising velocity in any column or pocket are (at least ideally) prevented from subsiding and so must overflow. Hydraulic classifiers or sizers are capable of making far sharper sepa¬rations than pool classifiers. The force causing settling may be gravity, or alternatively may be from centrifugal acceleration as developed in a centrifuge or hydra cyclone. Two things are needed to characterize the separation produced by classification: first, the size, D„ or equivalently the screen mesh at which it is made; second the sharpness of separation. Separation size may be defined in various ways. In closed-circuit grinding it is commonly specified by some point in the overflow screen analysis: For example, 5% on 65 mesh. In other applications, notably

Jan 1, 1985

By Tom H. W. Loomis

The department of the Interior is a federation or holding company of several fiercely independent bureaus which have either jurisdiction or expertise - or both - in a wide range of environmental fields. Each bureau is an advocate for its own concerns and an enforcer of its own mandates. This can be confusing to the company operating in the field. I will try to explain our concerns, help you see where we are "coming from," and give you some insight as to how we can help you. Other speakers have stressed the environmental concerns and site selection factors for uranium wastes so I will focus on the concerns of the Department of the Interior and some of the assistance we can give you in this area People are more aware and more concerned about environmental factors now than they used to be. Thus the past decade has brought about an evolution in both siting and design of uranium mill tailings ponds. Site selection criteria used to be simple - find a tract of land as near to the ore supply as possible with enough space and suitable topography for the expected volume of wastes. Site selections in the past have left a legacy of problems to be corrected - radioactive wastes on stream banks and in floodplains, mill wastes in and near established communities, and unprotected wastes subject to constant erosion. This is no longer acceptable environmentally or socially to a newly aware and concerned public. (Series of 30-35 slides showing uranium mine and mill wastes in Western United States. These illustrate environmental problems, reclamation and environmentally acceptable sites. The first group of slides are aerial shots taken in Wyoming and shows a surface mine and mill area. In the various views the pit, overburden piles, mill, and tailings pond can be seen. The next series were taken in Wyoming and New Mexico. These show various views

Jan 1, 1980

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By Zhang Youdi

A two-step approach has been developed for surface mine short term planning by the authors. The first step is mid term control and planning by the use of Goal Programming. This step gives optimal results for mid term planning (i. e. yearly or quarterly mine plan) as well as a macro control for short term planning (i. e. monthly or weekly plan.) The second step of the approach deals with short term production scheduling by the application of CAD technique and Systems Simulation. An interactive color character graphic design system has been developed with a software package. The menu-driven and module- structured package provides sufficient functions for surface mine short term planning and makes the model very flexible and user-friendly. This model has been applied to a large surface coal mine for short term planning optimization. Satisfactory results have been obtained. It is concluded that for complicated mining conditions this two-step combined approach gives an optimal control of mid term planning, makes the short term planning easier to avoid blindness; it has been proven that the Goal Programming is a powerful tool for solving multi-objective decision-making problems; guided by GP mid term planning, the CAD technique and simulation software package for short term planning are able to be concentrated on their practicality and flexibility.

Jan 1, 1992

By Richard Hogg, Heechan Cho

Investigations of long-time grinding of fine quartz (to about 80% passing 0.35 pm) in a 0.6 liter stirred-media mill are described. Breakage rates and primary breakage distributions have been determined based on extensive characterization of the ground products by laser scattering/diffraction and gas adsorption. The results indicate that, while there is qualitative similarity between the breakage parameters for ultrafine and conventional (coarse) grinding, there are important, quantitative differences. In particular, it is found that primary breakage distributions become significantly narrower in the submicron sizes. The trend can be described using double-truncated log-normal distributions in which both a maximum (breaking) size and a grind limit are specified. The breakage distributions become progressively narrower as the size being broken becomes finer. Breakage rates follow a typical, consistent pattern in which the rate decreases with size according to a simple power law. Further decrease in the rates seems to occur after very long grinding times when the entire mill contents become finer than about 1µm. The effect is explained as a result of changes in the rate/size relationship in the submicron range.

Jan 1, 1995

By Robert Turner

Gold and silver processing techniques are some of the oldest in the mining industry. Gold mining of high grade veins and deposits has existed for centuries. However, only with the higher gold prices in recent years and heap leaching techniques have the low grade gold and silver deposits become feasible to mine and process economically. By mining and hauling 3,600,000 tons of ore per year at an average grade of 0.03 ounces/ton gold and 0.385 ounces/ton silver, the Zortman- Landusky operations became profitable in 1982. To maintain profitably, a stripping ratio of less than one ton of waste to one ton of ore, and mine run ore placed on the leach pads which will yield approximately seventy percent go1 d recovery.

Jan 1, 1984

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By Francesco Chiappalone, Filippo Azzarà, Raffaele Aliberti, Daniele Nebbia, Lance Waddell

As part of the 3RPORT and NEBT Projects, 5-mile Combined Sewer Overflow Tunnels were excavated with a 19 ft diameter Slurry and 26 ft diameter EPB Tunnel Boring Machines. Due to the difficult geological and hydrogeological conditions, both tunnels were excavated maintaining a ground support pressure between 2 and 5.5 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of both projects while the second part focuses on the challenges and technical details of the pressurized breakthroughs that took place in deep shafts excavated in urban environment as part of the projects.

Dec 1, 2022

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By R. Bhaskar, H. Xie

Fractal theory was horn in the mid-1970s. Since then, its application has been spreading day by day, from mathematics and geology to areas such as geophysics, physics and material sciences. In this paper, fractal models are developed to characterize particle size distribution and surface area. Theoretical formulas are derived for the computation of fractal dimensions D (size) and D[s] (surface area). The models developed are applied using experimental data of particle size distribution and surface area obtained from the Microtrac Particle Size Analyzer for dust processed by several size reduction devices. The theoretical models and the experimental data are found in good agreement. The fractal dimensions obtained are D = 1.350 to 1.770 and D[s] = 2.058 to 2.584 for fine coal dust particles (< 15 µm) produced by various size reduction mechanisms. The physical meaning of these fractal dimensions is also related to the dust generation processes.

Jan 1, 1994

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993