Search Documents

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flow schemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none of them has led to a satisfactory conclusion. A technique was developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program was constructed that makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low-grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems. Key words: Modeling and simulation, Size reduction, Mineral liberation, Taconite, Magnetic concentrator

Jan 1, 2003

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By Edmond J. O’Donovan

South Bulga is a new longwall operation located in the Hunter Valley coal-mining region in Southeastern Australia. The mine’s objective is to achieve productivity levels significantly higher than the current industry average. From the day longwall production began, South Bulga’s output was below both budget and industry expectations, primarily because of the poor performance of the conveyor system. In the past, conveyor systems have been seen as an adjunct to the mine plan, not as an integral part. At past production levels, this approach may have been acceptable. In today’s mining operations, the conveyor system must be treated as integral and vital to the mining operation. The conveyor system is analogous to the vascular or circulatory system of the human body. Of itself, the system does not do anything, but if it is not functioning satisfactorily, the mine cannot operate.

Jan 1, 1996

By T. Hawthorne, H. Barnes

Homestake Mining Company has developed an estimating model, based on other closed projects, to audit and prepare new estimating plans. The results of recent closure audits reveal that the original budgets were often insufficient to cover the present expected expenses. Some of the major areas where technical challenges and costs are increasing include heap leach pile detoxification and rinsing, tailings dam closure, water management and treatment, abatement of contaminated soils, and many others. Risk and sensitivity analysis of each category will develop a level of confidence in the estimate and allow management to focus on the pertinent issues. Periodic audits of closure plans and costs throughout the life of mine serves to focus management attention on the complete costs of production. This will result in improved overall planning and management, and reduce the number of missed opportunities for savings.

Jan 1, 2000

By B. K. Mishra, R. K. Rajamani, R. Venugopal, P. Songfack

Millsoft is a computer-simulation software that predicts the performance of large industrial grinding mills. This software surpasses all other tumbling-mill analysis techniques available today because it is based on fundamental laws of physics instead of empirical correlations. Graphical user interface (GUI) forms simplify the specification of the following design and operating parameters: mill diameter, length, speed, charge density and size distribution, lifter material and geometry. All of these parameters are taken into account in the discrete element numerical technique that constitutes the essence of the simulation software. In turn, the software produces a visual animation of grinding-charge motion, predicts mill power and gives the distribution of impact energy. In this paper, a case study of an 8.5-m-(28 ft-) diam SAG mill is used to illustrate the application of Millsoft for mill design and trouble shooting.

Jan 1, 2000

By Norbert Patzelt

The high-pressure grinding roll was introduced about 10 years ago and has established itself in many applications. Most of these machines are used in grinding circuits in the cement industry. A few operate in conventional mineral-processing plants. Polysius has sold more than 350 Polycoms worldwide. An exception is diamond-ore processing in South Africa and Australia. This type of grinding system increases diamond liberation and reduces the capital costs for the downstream processing plant. There are several reasons why high-pressure grinding rolls have not been used more extensively in the mining industry: - The mining industry adheres to conventional grinding technology and regional preference for certain comminution circuits. - Design, scale-up and flowsheet assessment procedures are viewed as being immature and reduce confidence in the potential application of the technology. - Downstream process benefits are unproven on a plant scale.

Jan 1, 1995

By Josh Struble, Fu Yuet, Jan Zywiel, Kevin King

This paper discusses the application of Integrated Inertial/GPS technology for position determination of earthmoving equipment in an open-pit mine. Different GPS augmentation methodologies are introduced and discussed. Principles for the operation of the Applanix POS MC (Position and Orientation System for Machine Control) are also presented, together with test results conducted at the Twin Creeks Newmont mine, using the POS MC and Caterpillar’s CAES (Computer Aided Earthmoving System).

Jan 1, 2005

By R. E. Mclaughlin, R. J. McLaughlin, A. H. Danzberger

Acid mine drainage (AMD) can occur as a natural phenome­non through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhib­it low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations - the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiqui­tous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treat­ment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper. Within the family of chemical treatment processes, there are three principal recognized methods, namely, "Conventional," "High Density Sludge" (HDS) and "Heavy Metals Removal Process" (HMRP). All three are now employed or specified for treating AMO at mining sites which are being reclaimed under Superfund. Only limited data are available for more specialized chemical treatment processes such as "ferrate", borohydride membrane and electrochemical methods. Therefore, these data are not included here. Performance data for these three processes are presented in this paper and comparison among them is made. Comparisons include consideration of water quality, sludge characteristics, and operational ease. Capital and operational cost comparisons of these processes were addressed in a previous paper by the authors (see bibliography). The results presented here are impo1tant not only to metals mining, but are also applicable to other industries experiencing metals-laden acidic wastes including: coal mining and prepara­tion, metal plating, and electronics circuit board manufacturing. The acceptance of any process should be based on bench scale demonstration before implementation is contemplated. The three processes included herein are discussed in relation to the particular sites at which they are in use, or their use is planned. The sites selected were representative of the various types of processes and the wastewater parameters.

Jan 1, 1998

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By Richard Druesedow, Richard Ray

Tests at the VP-5 "C" shaft fan installation of Island Creek Coal's Virginia Pocahontas Mines were performed to determine pressure drop due to the design of the shaft collar and ductwork leading to the fan. Data from the test locations in the shaft, duct and fan indicate significant pressure losses in the system as well as significant turbulence in the flow. Data taken with a 3-D probe in the fan annulus confirmed the importance of using this type of instrument in turbulent flow applications. This data will be later supplemented with data taken after addition of turning vanes in the 45° turn adjacent to the fan inlet.

Jan 1, 1993

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By P. Whincup, T. Showell, B. Marchant, R. Dunne

An oversupply of copper on world markets in the early 90' s, coupled with a decrease in demand, resulted in a "tight" market for the sale of copper concentrate. In these conditions small producers of low grade copper concentrates found it difficult to sell their products. The situation was exacerbated for those producers also having reasonable quantities of penalty elements (e.g. As, Bi). The Telfer Gold Mine bulk copper gold concentrate, produced from treating underground sulphide ore, fell into this category (i.e. 16% to 20% copper, 30% to 35% sulphur and 3500ppm to 4500ppm arsenic). The concentrate sulphide minerals are predominately chalcocite and pyrite. Although a higher grade copper concentrate was attainable a substantial decrease in gold recovery ensued. Under the prevailing market conditions a decision was made to stockpile concentrates pending either an easing of market conditions or alternatively finding an on site method for treating the concentrate to recover both the contained gold and copper.

Jan 1, 1995

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

Opencast mines are vulnerable to inclement weather conditions as it disrupts the day-to-day activities at these mines. To address the problem, a perceptive driving assistant system (PDAS) has been developed to increase the visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery (HEMM) at opencast mines in harsh weather conditions.

Apr 1, 2023

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002