Search Documents

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By V. C. Rogers, K. K. Nielson

INTRODUCTION The potential health impact from uranium milling operations is mainly associated with long-term releases of radioactive contaminants from the mill tailings.(1,2) The major mechanisms for mitigating these potential releases focus on increasing the tailings containment with the addition of migration barriers such as thick earthen covers and clay liners. Some limited investigation has also focused on reducing the radionuclide source terms. This alternative approach has some desirable features, but stringent cost requirements are placed upon source removal methods in order for them to be economically favorable. A cost effectiveness evaluation is presented herein, in which costs for containment methods are used to establish maximum cost guidelines for the source removal methods. The 230U decay chain, shown in Figure 1 contains the radioisotopes of major concern, 230Th, 226Ra, 222Rn and its short-lived alpha-emitting daughters, When the uranium is removed in the milling process, these isotopes, which are normally not removed remain in the tailings solids. The general pathways to the environment from uranium mill tailings are depicted in Figure 2. The dominant pathways are radon to the atmosphere and radium and thorium to a groundwater aquifer. The magnitude of the contaminants released into these pathways can be characterized by the following parameters: 1. The 230Th and 226Ra content. 2. The emanating power for radon. The fraction of radon generated that is free to migrate. 3. The leach rates. Source reduction methods seek to reduce the magnitude of any or all of these parameters. In general the dose rates are proportional to the source terms. For radon production the source term is proportional to the product of the radium concentration, R, and the emanating power, E, so that the risk is reduced by the same factor that reduces RE. For example, if the radium content is reduced by 95 percent, but E is increased by a factor of two, then the dose rates are reduced by an order of magnitude. The source term for the groundwater pathway is not as easy to identify. The peak in the radium concentrations in the accessable water body can also

Jan 1, 1981

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By Kalyan K. Bhattacharyya

A systematic slope design for open-pit mines has become a reality only in recent years. Advances in the science of rock mechanics, coupled with extensive use of computers, have enabled the numerical solution of slope design problems which were not previously amenable to analytical or numerical solution. This slope stability study was performed for the UJV-SB open-pit uranium mine of the Getty Oil Co., located in the Shirley Basin area, Wyoming. The purpose of the study was to determine the appropriate slope angles for a starter pit. The data generated during the mining of the starter pit would test the initial design and suggest appropriate modification in the design for future mining in the project area. There had been a history of slope failures in the open-pit uranium mines in the area due to the low competency of the overburden materials and adverse hydrological conditions.

Jan 1, 1979

By E. P. Chen

This investigation involves the development of a two-dimensional continuum model for the description of jointed media. Specific application of the model developed here is for the potential geological disposal of radioactive waste in the layered sequence of fractured volcanic tuffs under Yucca Mountain, Nevada. This is currently being considered by the Nevada Nuclear Waste Storage Investigations Project, administered by the Nevada Operations Office of the U. S. Department of Energy. The work is a direct extension of the previous constitutive model by Thomas (1982) based on the work of Morland (1974). The main feature of Thomas's model includes two parts: a continuum approximation based on average discontinuous displacements across jointing planes within a representative elementary volume, and a material constitutive description based on linear elastic matrix material behavior and nonlinear normal and shear joint behavior between jointing planes. The mathematical descriptions by Morland based on strain partitioning among matrix material and joint sets allow multiple joint sets to be included in the model. However, the initial effort by Thomas to implement Morland's mathematical model included only a single set of joints. To make the material model reflect more realistically the field characteristics, the current work extended Thomas's model to include orthogonal sets of joints. The nonlinear elastic normal joint behavior is retained in the present model. Joint shear response was treated as linear elastic in the shear stress versus shear displacement relationship prior to attaining the stress level governed by the Coulomb friction criterion. Beyond this critical stress value, a horizontal line is assumed in the work of Thomas for the shear stress versus slip displacement relationship such that the shear stress remains constant while the slip displacement increases. Motivated by experimental observation, the current work generalized the shear response to allow a line with finite slope to govern the slip behavior beyond the critical stress level. The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Formulation of the Continuum Model The inclusion of an orthogonal joint set led to a fourth order algebraic equation for the calculation of stress increments as compared with a second order equation obtained by Thomas. The nonlinear elastic normal joint behavior provides criteria which allow the selection of the root that yields result consistent with the loading condition of the problem. The addition of one more set of joints provides the potential to more completely study the interaction of various parameters representing the characteristics of jointed media behavior. Material responses to various loading conditions based on the present constitutive model have been obtained. These results and their comparisons to single joint set results are presented. Let us focus our attention on the set with normal n first. Let the jump dilation displacement and jump slip dasplacement associated with the [ ]

Jan 1, 1986

By Edward J. Zeigler, John T. Miller

INTRODUCTION Construction of Phase I, Section A, of the Baltimore Region Rapid Transit System required that six underground stations be built using a cut and cover excavation technique. For five of these stations, soldier piles, used as support of excavation, were installed with tip elevations well below the bottom of the excavation. However, in the case of the sixth subway station, the Mondawmin Station, soldier piles were installed only through soil and decomposed rock, with the tips of the piles being stopped well above the bottom of the excavation in partially decomposed rock. Below the tips of the soldier piles, and below a cut slope where piles were not installed, the sides of the excavation consisted of partially weathered and fresh rock and were supported by a combination of rock bolts, wire mesh and shotcrete. An extensive installation of geotechnical instrumentation permitted detailed monitoring of horizontal and vertical movements of the soldier piles and the walls of the excavation. Preliminary studies indicated that the excavation support system selected for the Mondawmin Station would have several advantages over a conventional system consisting of soldier piles extending to the bottom of the excavation, braced with prestressed struts. These advantages included lower cost of installation, a decreased time required for installation, and a more open excavation for the contractor during construction of the station. The Mondawmin Station is situated in the northwestern quadrant of Baltimore City, approximately 6.4 km (4 miles) from the center of the City. The station lies midway in a project 12.9 km (8 miles) long identified as Phase I, Section A, of the Baltimore Region Rapid Transit

Jan 1, 1981

By Wei Bin, Liu Zhe, Liping Xiao, Jichi Bai

The Acid Mine Drainage has characteristics of low pH, high concentrations of heavy metal ions, such as Fe2+, Mn2+, Cu2+ and Zn2+. In this paper, the composite particles that consisted of bentonite and steel slags were used to dispose the Acid Mine Drainage. Bentonite is the mineral materials and can adsorb heavy metal ions excellently. The steel slags are alkaline and industrial solid waste for the treatment of the Acid Mine Drainage. The main influencing factors, such as adsorbent dosages, shaking rates, concentrations of heavy metal ions, temperatures, adsorption time and pH value were studied by the static experiment. Increasing the adsorbent dosages and the concentrations of the heavy metal ions, speeding up the shaking rates, raising the temperatures, extending the adsorption time and improving pH would improve the removal efficiencies of heavy metal ions. Through considering the removal efficiencies and the treatment costs, the optimum reaction conditions for the four kinds of heavy metal ions were obtained. The adsorbent dosage 21 mg/L, the rotational speed 120 r / min, the temperature 25?, adsorption time 100 min and the initial wastewater pH 7. The four kinds of heavy metal ions existed independently in the simulated mine wastewater. The highest initial concentrations of Fe2+, Mn2+, Cu2+ and Zn2+ were 150 mg/L, 100 mg/L, 170 mg/L and 140 mg/L respectively. The removal rates were 93.42%, 92.64%, 93.86% and 95.17% respectively. The determination of the particles’ SEM-EDS Microscopic characterization showed the composite particles could play a part in neutralizing, absorbing and the chemical precipitation. The acidity decreased notably and the heavy metal ions of Fe2+, Mn2+, Cu2+ and Zn2+were adsorbed and precipitated effectively. The research results can extend the practical engineering application of the composite particles.

Jan 1, 2017

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By Bezalel C. Haimson

Long before excavation begins, the in situ stresses in the horizon of planned underground chambers can be measured by employing the hydrofracturing technique in existing exploratory holes. Such measurements produce the stress magnitudes and directions required for the rational design of rock structures. Two recent case histories are cited in which preexcavation stress measurements for the design of underground powerhouses proved very beneficial in the orientation of the chambers and the estimation of the stability and required support. A third stress measurement case is related to the preexcavation design of tunnels that will house doughnut-shaped superconductive magnets for the storage of electric energy. In all cases, expensive later modifications were probably prevented by measuring stresses early in the design stage.

Jan 1, 1976

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By Gregory Owen Lewis, Wendy Bouwer

Various processing strategies have been implemented in an effort to limit the loss of gold, during leaching, to the naturally-occurring carbonaceous 'preg-robbing' constituents present within certain gold bearing ore sources. Certain processing routes include complex and costly pre­treatment steps to reduce the negative effects of the preg­robber prior to dissolution, while others adopt a simpler direct leach/recovery approach. Process selection is largely dependent upon the gold deportment and the nature of the preg-robbing constituents within the particular ore. In the case of carbonaceous ores in which the bulk of the contained gold is available to direct cyanidation, carbon-in­leach (CIL) technology is generally applied with varying degrees of success. The effectiveness of the CIL route is governed by the competitiveness of the preg-robbing constituents in relation to activated carbon for the preferential adsorption of the solubilized gold. Trials have shown that the DOWEX MINIX strong-base gold-selective ion exchange resin has gold loading characteristics superior to those of activated carbon. The faster gold loading kinetics, together with the higher capacity of this resin, favour its use in an in-leach application as a more effective adsorbent for complex ores. This paper introduces the alternative resin-in-leach (RIL) technology, compares the metallurgical responses to RIL processing of different problematic ore sources, and discusses the interaction between various process conditions. Selected results from laboratory and pilot-scale testwork are presented to highlight the discussion.

Jan 1, 2000

By Stacey Leichliter

The Cripple Creek and Victor (CC&V) Gold Mine (Cresson Project) (Fig. 1) is undergoing an expansion to extend production to the year 2025. This expansion involves building a high-grade ore mill, another valley leach facility (VLF) for heap leach operations and expanding the overburden storage areas. The current operating pits are progressing downward from the oxide ore into a more sulfide and telluride-rich orebody. There is still oxide ore present in the current pits and planned pits not yet mined. There is an increased need for two recovery processes for these two different types of ore. The key component to this expansion is the high-grade ore mill, which has gravity, flotation and carbon-in-pulp (CIP) circuits. The mill will be the main recovery process for the higher grade, more sulfide/telluride-rich ore. This ore type does not recover well on the heap leach pad due to its refractory nature. Geometallurgy is vital for ore characterization for the two recovery methods. Geometallurgy helps develop indices that are used to predict parameters that influence overall recovery and production, such as hardness, crushability, grindability, pH fluctuations, gravity (coarse) gold, flotability and cyanidability. Using geology and mineralogy along with other analytical data, geometallurgical models are constructed and applied to the resource block model for proper planning and extraction of the gold. Geometallurgy aims to analyze the variability in the different responses to the parameters to help reduce risk (costs) and optimize recovery (profit).

Jan 1, 2013

By K. C. Kane, D. L. Meredith, B. E. Davis, D. A. Stanley, O&apos

Computer control of the minerals beneficiation process is limited by a lack of adequate sensors to provide information on the current state of the process. Recent reduction in the cost of image acquisition and powerful inexpensive computers make use of computer vision as sensory input in process control a possibility. In the phosphate industry, the amount of apatite in phosphate tailings is estimated by inspection. For machine vision, a simple 256 x 512 color image of the tailings was captured via an inexpensive color video camera on an IBM PC. Initially, the image is converted to gray scale and displayed on an EGA color monitor. A program was written which identifies the different constituents of the sample by analyzing the gray scale levels for the digitized picture. In other instances the minerals are identified by their relative color intensities. The amount of each constituent is determined with good accuracy from the area it occupies on the image.

Jan 1, 1990

By Don Fisher, Jean Juilland

Introduction A section of the Federal Land Policy and Management Act of 1976 specifies the procedure for areas the US Bureau of Land Management manages that have wilderness qualities. In part, FLPMA specifies that within 15 years of its approval, the Secretary of the Interior shall review roadless areas of 20 km2 (5,000 acres) or more and roadless islands of public lands identified during the inventory as having wilderness characteristics described in the Wilderness Act of 1964. Further, the Secretary shall report to the President his recommendation as to the suitability of each area or island for preservation as wilderness. However, before any recommendations for, wilderness designation, mineral surveys shall be conducted by the US Geological Survey and the US Bureau of Mines to determine if any mineral values are present. And finally, a Presidential recommendation for wilderness designation becomes effective only if so provided by an Act of Congress. BLM Inventory Procedures To fulfill these legal requirements, BLM is inventorying the land it manages for wilderness qualities. Since the law sets special provisions for Alaska, BLM included in its inventory only the public lands it manages in the conterminous US. In 1980, after public input, BLM picked 967 areas to be considered as Wilderness Study Areas. All of the selected WSAs are in 11 western states and the areas total about 97,128 km2 (24 million acres). From these 967 areas, through its multiple-use planning system, BLM is making initial recommendations of areas to be considered suitable for preservation as wilderness. Those WSAs that BLM initially considers suitable for wilderness preservation will have mineral surveys conducted by the USGS and the USBM, to determine mineral values. Based on these mineral surveys and other resources information including wilderness qualities, the Interior Secretary will report to the President his recommendations on the WSAs suitable for wilderness preservation. To make the initial recommendation of suitability, BLM managers will need information about geology, energy, and mineral (GEM) resources as well as information about other resources. BLM has begun a GEM assessment program to provide its managers with that information. This program is designed to provide information for a WSA suitability decision process that aims to supply minimum necessary GEM information. In essence, the program will provide preliminary assessment of the mineral potential for each WSA. Assessing the WSAs To accomplish this, a two-phase program was designed. In phase one, only existing data are collected and used. In phase two, new data are generated and added to existing data. Phase two begins only if BLM geologists, mining engineers, or managers consider the information provided in phase one as inadequate. This avoids unnecessary work and expenses and allows the program to proceed without undue delay. Figure 1 shows the two-phase process, including BLM's GEM in-

Jan 10, 1983