Search Documents

By Eugene F. Casey

The next ten to fifteen years will be exciting ones for the construction industry because three city agencies alone have started or will start, on tremendous expansion programs, the cost of which will exceed a total of four billion dollars. The major portion of this work will be done by the use of tunnelling methods. *Tunnelling is construction by any method of a covered cavity of predesigned geometry whose final location and use under the surface, whose cross-sectional area is greater than two sq. meters. The New York City Transit Authority's expansion program will provide for approximately 52 miles of new subways. The Board of Water Supply has already started on City Tunnel No. 3 which, when completed will provide the City with enough water until the year 2000, and the Board of Water Resources has embarked on a tremendous program to clean up the surrounding waters. Yes, these will be exciting years, particularly when one reads about the new novel exotic methods of rock breaking and disintegration, coupled with the new methods of soft ground tunnelling.

Jan 1, 1997

By J. L. Weeks

Discussion by J.L. Weeks Discussion I wish to comment on Kissell and Sacks's paper "Inaccuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines." It is well established in industrial hygiene that area sampling is not an accurate measure of personal exposure. To measure personal exposure, one must use a personal sampler. Kissell and Sacks, using data from coal mining, reached the same conclusion. This is the right answer but it is the wrong question. This issue arises because the machine-mounted respirable dust continuous monitor (MMRDCM) is being considered to monitor coal-miners' exposure to respirable dust. This device may be mounted on a continuous mining machine, and it would take a modified area sample. I refer to it as "modified" because a mining machine is not really a fixed location, as is the typical area sample. The concern with whether this machine would provide an accurate estimate of the machine-operator's exposure, however, overlooks important features of the MMRDCM. Specifically, it displays dust concentration as it occurs and at the place where it is needed, not 10 days later, as is the case with the current system. Used in this way, it allows for timely intervention to control exposure to dust and it leads to greater first-hand knowledge of specific conditions and mining practices that result in excess exposure. If one knows the dust level is excessive at the time the dust is being generated, it is possible to use known and effective methods of dust control to reduce exposure. By measuring again, one can determine whether control methods have worked. This is a generic procedure followed in any industrial process: measure, adjust and measure again. It leads to more effective and more efficient dust control and is preferred to taking a sample, waiting 10 days for the results and then trying to apply that information to a situation that no longer exists. The MMRDCM also records the dust level automatically, and it runs continuously, making it harder to tamper with. Dust monitoring in underground coal mines has been corrupted by some operators having submitted fraudulent samples (and being convicted on criminal charges because of it), weakening the credibility of the current system. The MMRDCM is, in part, a response to this corruption, and an effort to focus attention on dust levels and dust controls rather than on the perpetrators of fraud. Use of the MMRDCM is an evolutionary change from the current system. With the current system, one takes a personal sample of exposure of the "designated occupation" (DO, defined at 30 CFR 70.2 (f)), the occupation regularly exposed to the highest level of dust on a section. Typically, on sections using continuous mining machines, this is the mining-machine operator. The rationale behind DO sampling rests on some of the findings that Kissell and Sacks report. They reviewed several studies that showed that dust concentration varies with location on a mining section and that there is a concentration gradient with the highest concentration occurring closest to the face. The logic behind DO sampling strategy is that if the dust concentration at the place where it is highest is below the exposure limit, then concentration elsewhere on the section is also below the limit. In this way, one will have achieved the objective or keeping dust concentration below the exposure limit for all miners on the section by measuring the exposure of only one miner. The

Jan 1, 2003

By E. Watkins, S. J. Schatzel, V. Gangrade, K. M. Ajayi, Z. Khademian

Longwall-induced deformations could jeopardize the mechanical integrity of shale gas well casings positioned in the abutment pillar of a longwall mine. The in situ and induced fracture networks surrounding the gas well could provide pathways for gas flow into the mine creating safety concerns. Hence, this study by the National Institute for Occupational Safety and Health (NIOSH) develops a discrete fracture network (DFN) model to characterize the fractures in the overburden based on geomechanical analyses of mining-induced fracture apertures at a study site in southwestern Pennsylvania. The apertures from the geomechanical model are used to develop a stochastic DFN model of the site in fracture flow code (FFC). Multiple realizations of the stochastic DFN model that replicate potential fracture geometries are simulated, and the fracture permeability is compared with field measurements. A maximum field measurement of 5.03 × 10− 12 m2 (5080 mD) and 3.82 × 10− 13 m2 (386 mD) was estimated over the abutment pillar at the Sewickley and Uniontown horizon, respectively. The results show that the average permeabilities from the DFN model agree closely with the field measurements. In addition, the comparison of all the field measurements and 100 DFN realizations show the model is representative of field conditions. These findings provide critical information regarding fracture characteristics in the overburden, which will further be used to predict potential shale gas flow to the mine in the event of a casing breach for an unconventional gas well.

Jun 17, 2022

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By J. A. Eisele, G. E. McClelland, M. D. Wroblewski

The Bureau of Mines is conducting research at its Reno Research Center to develop a staged agglomeration-heap leaching system and to electrowin the dissolved precious metals from the pregnant leaching solution. For direct electro- winning to be successful, the pregnant solutions generated during the Initial stages of leaching must be higher grade than obtained by conventional heap leaching. The precious metal concentration of the pregnant solution can be Increased by agglomeration pretreatment with cyanide solution which starts the leaching process during the curing period, by leaching with small volumes of solution and by cycling the leaching solution through more than one heap in a staged manner. The resulting pregnant solution is passed directly through an electrowinning circuit. The barren solution from electrowinning is recycled to the leaching circuit. Bench-scale research on the development of the staged leaching system and on the development of an efficient electrowinning cell are described. The Bureau of Mines developed agglomeration- heap leaching technology. This technology was readily adopted by the mining Industry for heap leaching crushed ores and mine wastes. Current research involves the application of this technology to finely ground feed materials such as precious metal-bearing milled tailings. Tailings agglomeration-heap leaching has also been used commercially.

Jan 1, 1984

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

Cripple Creek and Victor Gold Mine is an epithermal gold deposit located in the Rocky Mountains of Colorado. Surface operations are continuing along with an expansion for an onsite mill to take place in the next couple of years. The surface pit is currently progressing downward from an oxidized zone into a transitional, more sulfide/ telluride-rich zone. Gold mineralization includes native gold, electrum, and tellurides. Cyanide heap leaching is the recovery process for the oxidized ore with the sulfide/telluride-rich ore to be processed at the new onsite mill. Ore characterization prior to mining is vital when there are two possible recovery processes. This characterization is dependent on geometallurgy. To identify the causes of the variability, multiple parameters are analyzed and assayed. These parameters are measured by a variety of analytical testwork. The analytical testwork provides measurements for the desired parameters. Geometallurgical models are developed for the parameters per recovery process, so estimations can be inserted into the resource model to optimize operations and recoveries.

Feb 27, 2013

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By V. Badaker, R. J. Sweigard, C. D. Barton, J. W. Stringer, J. M. Ringe, A. D. True, D. H. Graves

Field studies have demonstrated the relationship between the growth of high-value trees on surface mined land and the physical conditions of the root growth medium. Specifically, the survival and height of hardwoods grown on less compacted material are far superior to those grown on compacted material. Furthermore, studies have demonstrated that the physical condition of the root growth medium can be characterized by dry bulk density and penetrometer resistance and that these parameters are also related to tree growth measurements. Site indices are useful for evaluating and predicting the productivity and timber yield for a specific location. A method has been proposed to estimate the site indices for various tree species on reclaimed surface mined land as a function of the physical properties of the root growth medium.

Jan 1, 2005

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump&apos;s efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By H. R. Quina

Phosphate is one of the most important minerals in our world today. It contains the life-giving element of phosphorus, which is essential to the growth of every living cell in plant, animal, and man. This vital mineral is found in twenty-three states of the United States; however, for more than 70 years, Florida has led the nation in phosphate-production and now produces 70% of the requirements of this country. Since the early 1880% when rich phosphate deposits were accidentally discovered in a river-bed in Central Florida, the industry has developed into a multi-million-dollar operation. Phosphate mining began in Florida in 1887 with very crude methods and equipment. The original process was necessarily slow and tedious, resulting in total production of 3000 tons in 1888. Progress was made in improved mining operations, and by 1894. Florida had grabbed the lead as the nation?s largest phosphate-producing area, and is still in the top position.

Jan 1, 1962

By Lane White

Refractory gold ores are those from which a significant percentage of the gold cannot be recovered by conventional cyanidation. Historically, roasting has been the primary method for rendering such ores amenable to gold extraction; however, roasting creates environmental problems that are not acceptable in many locations. During the 1980s, consistently strong gold prices drew increasing attention to refractory gold ores, and new processing schemes were commercialized, most prominently aqueous pressure oxidation and more recently bacterial oxidation. Since 1985, pressure oxidation has been incorporated into four plants processing refractory gold ores. A fifth plant is scheduled for start-up in early 1990, and three additional plants are scheduled for production before late 1992. A technical session on treatment of refractory ores was included in the program of `World Gold &apos;89, a Gold Forum on Technology and Practices&apos; held by SME and the AusIMM in Reno, NV, Nov. 5-8, 1989. This article summarizes material from five of the papers presented during the refractory gold session and published in the proceedings of `World Gold &apos;89,&apos; edited by Roshan Bhappu and Rod Harden. The complete proceedings are available from SME Publications Sales, P.O. Box 625002, Littleton, CO 80162-5002 $53.50 for members, $38.50 for student members, and $73.50 list price.

Jan 1, 1990

By Kyle L. Brennan, Scott Maybrier, Gang Chen, Scott Huang

Data from about 3200 drill holes in the offshore area at Nome, Alaska was digitized and processed. Most drill hole files have associated lithology, gold value, and blow count descriptions for each drill hole. The gold intensity was used to present the potential gold resource in the study area on the world wide web. A web page was created that gives background information on the project, descriptions about the Nome area, maps of the claim blocks that include all the normalized slices of gold deposits, and links to other relevant sites on the web. The site is located at http://mineral.uafsme.alaska.edu/nomeproject/nomehome.htm.

Jan 1, 2002

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006