Search Documents

By Gordon V. lewis

The Penjom gold mine treats highly preg-robbing carbonaceous ore by using relatively inexpensive gravity and hydrometallurgical methods. The mine is a joint venture between Avocet Gold Limited, a subsidiary of Avocet Mining PLC, a U.K listed mining company with interests in gold and tungsten, and the Pahang State Development Corporation (PKNP) who receive a 2% royalty. The operating team at Penjom embarked on a programme of innovation during 1998 following a realisation that almost all of the primary ore in the gold deposit was highly carbonaceous in nature. Earlier attempts at desliming and leaching the deslimed product through a normal CIL circuit had failed, and through shear necessity, the team turned to new technologies which were considered most suited to the ore characteristics indicated from pre­feasibility testwork. Between April and September, 1998, the mine introduced three key processes, which combined represent the elements of "The Penjom Process". The gravity circuit was boosted to maximise the capture of leachable sulphide and free gold from the relatively carbon free cyclone underflow stream, kerosene and diesel blanking was introduced to treat the cyclone overflow and RIL (resin-in­leach) technology utilised to replace the existing CIL (carbon-in-leach) circuit. Further experimentation with selective resin in partnership with Mintek of South Africa yielded a significant improvement to the process during 1999. Minix­Dowex resin was introduced mid year to replace a non-gold selective resin, which had been used in a flotation/batch leaching circuit for about nine months. Lower carbon levels in the feed at that stage led to the abandonment of flotation and the introduction of continuous RIL, which has been adopted as the major chemical process at the Penjom gold mine since September, 1999. Given the proven performance of the circuit to date, this process may be considered as a low cost option for the treatment of highly carbonaceous ores, particularly those which are not refractory and contain a reasonable percentage of free gold.

Jan 1, 2000

By A. Aubut, A. Proulx, O. Tavchandjian

Results obtained from conditional simulations and multiple indicator kriging were compared in the assessment of two different mining methods proposed for the extraction of the down-dip extension of a nickel-sulfide ore body located in the Thompson mining camp, Canada. An enhanced turning band simulation algorithm, supplemented with an unfolding technique, was used. A floating stope optimization process was used to effectively compare tonnage and grade figures. A calibration exercise was also conducted in the upper portion of the ore body. This study demonstrates that conditional simulations provide better spatial models for conceptual mine design and capital budgeting decisions.

Jan 1, 2004

By Martin F. Grier

The Mt Todd Gold Project is located 300km to the south of Darwin in the Northern Territory of Australia. The identified resource comprises 46 million tonnes at 1. 65g/t using a 1. 0g/t cut-off ( 50 million short tonnes at 0.05oz/st). The resource is open to the north and at depth. Mineralisation comprises easterly dipping sheeted quartz/sulphide veins, typically 10 to 20 millimetres in thickness, hosted by hornsfelled greywackes. The majority of the ore body is primary ore with only 10% classified as oxide ore. Early testwork showed that the ore was not suitable for heap leaching, giving only 50% recovery at a -3mm crush size. Acceptable recoveries were obtained at a P80 of 75 micron. However, the ore is extremely hard.

Jan 1, 1992

By R. B. McCammon

Four areas have been identified as favorable drill-site locations for determining whether or not a suspected prophyry copper deposit exists in Rowe Canyon, Nevada. Favorability is based on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for the elements zinc, silver, arsenic, antimony and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1979

By Luis Dr. Sobral

In this study, the removal of zinc, cadmium and copper from an aqueous sulphate solution, derived from the biomass desorption process, was examined by using a reaction system with a three-dimensional high surface area electrode (RNiF). This reaction system was found to be extremely effective in reducing metal concentrations to the ppb range. The effect of cathode potential and flow rate were studied for three different nickel foam porosities. In addition, current- potential curves were recorded, at a rotating vitreous carbon electrode, to deter- mine the possibility of depositing the aforementioned metals separately.

Jan 1, 1998

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By M. ]. [Mohkam

The paper describes the features of the problems encountered and the countermeasures taken for two different tunneling projects. Where, slurry shields were used to excavate, in soft heterogeneaous water-bearing grounds, tunnels passing at very low cover beneath existing foundations of H.T. electric pylons, underground structures and major utilities. In order to avoid any ground failure and/or damage to the existing structures, one option was ground treatement by grouting or freezing technics. However, it was judged that, based on previous experiences, excavation with slurry shield could be carried on securely using an appropriate slurry enriched with polymers and applying a well determined pressure at ground face. A three dimensionnal limiting equilibrium analysis model was used to determine proper confinement pressures. And, the appropriate slurry compositions were stabilished based on laboratory test results. The tunnels were excavated successfully, no ground failure was experienced, and the maximum settlement recorded (on pylons) didn't exceed 3 mm.

Jan 1, 1991

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By J. M. Mutmansky

The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous-miner-generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory-generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared.

Jan 1, 1995

By M. A. Cristovici

The use of surfactants as wetting agents to suppress sulfide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulfide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactant adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1992

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12'-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

By Randal J. Barnes

The January 1988 issue of Engineering and Mining Journal includes two short articles on blasting practices in surface gold mines (Anon., 1988 ; Carr , 1988). A reader of these articles learns, among other things, that a "12 x 13 ft" blasting pattern is used at the Carson Hill Mine, and a "17-ft burden and 18-ft spacing" is used at Echo Bay Mineral's Borealis operation, while at Mascot's Nickel Plate Gold Mine "ore shots are on a 10 x 10 ft" pattern. Like a new edition of the World Book Almanac, these articles are overflowing with useful tidbits of technical data; but, they never mention why the particular blasting patterns were selected. A survey carried out during the Winter of 1988 at six surface gold mines in the western United States also failed to produce a satisfactory answer. The responses from mine planning engineers to the question "why is your blasting pattern X by Y", reduced to "we use X by Y here because we used X by Y at our last operation, and it worked ok." Certainly, with the available decades of experience and professional practice in blast holes design, rock fragmentation in surface mines has been thoroughly investigated. However, and this is the central issue, fragmentation of the rock is not the primary purpose of most rotary drill holes in surface gold mines. Quoting senior mine engineers from companies operating, three of the richest surface gold mines in the world (AMAX Gold, Homestake Mining, and Gold Fields Mining)

Jan 1, 1989

By S. Pignolet-Brandom, E. Fregeau-Wu, I. Iwasaki

To recycle steelmaking slags for their iron, manganese and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote sufficient grain growth to achieve liberation. In situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate and the addition of fluorspar promoted grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modeling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1993

By D. W. Fuerstenau

The flotation behavior of quartz in the presence of alkyl ammonium acetates as a. function of alkyl chain length has been interpreted in terms of hemi-micelle formation at the solid-liquid interface. The van der Waals cohesive free energy that is responsible for hemi-micelle formation has been found from these results to be 1.02 kT per CH group. This 2 is in excellent agreement with literature values obtained from research on the properties of micelles in bulk systems.

Jan 1, 1964

By Clifford R. Haryett

The potash industry in Saskatchewan, Canada, has advanced in numerous mining and ore processing areas over the last decade. This article describes these innovations and their effect on the industry in the area. During the 1970s, Canada's Saskatchewan province became a world leader, second only to the USSR, in potash production for crop fertilizer. Despite a serious oversupply in the early part of the decade, and a drop in demand due to the agricultural impact of the oil crisis, the Saskatchewan potash industry continued to make extensive capital expenditures to bring mining and processing innovations onstream. These innovations were directed at reducing production costs, improving work conditions, and overcoming environmental concerns.

Jan 8, 1982

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006