Search Documents

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By R. L. Grayson, N. P. Reddy, D. A. Kinzler, S. Yuan, W. R. Myers, R. A. Wells

An examination was conducted on the impact of roof conditions and the mining cycle in determining a representative respirable mass concentration at the mid-shearer location on a longwall panel. Multiple personal gravimetric dust samplers, operated at a flow rate of 2.0 lpm, were used at different locations along the face to isolate the concentrations and variances associated with good and bad roof conditions under both the cutting and cleaning mode of operation. The number of samples needed to estimate the population variance at a given confidence level was analyzed. In addition, the statistical analysis showed that the coefficient of variation of dust concentrations at different locations and under different conditions ranged from 0.185 to 0.475, with an average value of 0.283. The estimates of the average dust concentration for a shift and the variance of the dust concentrations were calculated. A total of 48 data points were available for an [a x b] factorial ANOVA (analysis of variance). The estimates of the variance components were determined. The results from F-tests indicated that both the roof conditions and mining operations had a significant effect on the respirable dust concentration. There was no significant interaction effect between mining operations and roof conditions. In conclusion, this study shows that not only should sampling and analytical errors be considered in determining the required number of samples for a good estimate of the long-range exposures of miners, but also fluctuations of concentrations due to mining operations and geological conditions should be taken into account.

Jan 1, 1991

By Murray D. Lester

The relationship between bauxite and energy has two distinct aspects. On the one hand, since virtually all of the bauxite that is mined winds up as aluminum metal, the economic health and future of the bauxite industry and of the bauxite-producing countries depend on the continuing vigour and competitiveness of aluminum against alternative metals and materials. The price of aluminum is, in turn, particularly dependent on the price of energy. Hence, the need for bauxite is ultimately affected by the price of energy. The second aspect relates to location of the bauxite industry. There is no shortage of bauxite resources in the world. For various reasons, as we shall see, there is a growing tendency toward the integration of bauxite mining, bauxite refining and aluminum smelting in those countries that have the resources both of bauxite and of energy necessary to support the entire production chain. Thus, the availability of attractive energy supplies will increasingly favour development of bauxite mining: the traditional export of bauxite as a simple raw material is likely to diminish in relative terms. In short, both the amount of bauxite mined and where this mining will take place are related to energy considerations. Let us first have a brief look at the four basic activities that are involved in our integrated operations: A. The bauxite is mined and moved to an ore plant. This step does not require more than relatively modest amounts of energy normally associated with excavation, loading and shipping of any bulk material. We need about four or five tonnes of bauxite for every tonne of metal produced.

Jan 1, 1984

By William E. Spence

Gold was discovered at the Haile mine in Lancaster County, South Carolina in 1827 or 1828, and since that time the mine has been worked intermittently by both open pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 ounces. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores.

Jan 1, 1978

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996

By Harold D. Taylor

Cone fitting is a procedure which can be used to estimate the short range, linear portion of a variogram. Rather than combining data over windows In different directions and fitting by hand, cone fitting estimates the variogram in all directions at once using a multiple regression approach. The method automatically provides estimates of nugget effect, anisotropy, and initial slope of the variogram. This paper presents the results of simulation studies which have been carried out. These studies Indicate that the method works well and that it may be particularly useful for small data sets. The simulation studies also indicate that the local variogram may differ greatly from the theoretical variogram.

Jan 1, 1986

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By Douglas W. Fuerstenau, Douglas M. Deason

The depletion of high grade siliceous phosphate ores is bringing about a search for economically processable replacements. The processing of unexploited dolomitic sedimentary phosphate reserves has numerous problems including the similar surface properties of the carbonate and phosphate minerals and the presence of significant concentrations of dissolved species in the flotation pulp. In this paper, inorganic adsorption and surface transformation phenomena exhibited by the dolomite/apatite systems are examined in detail. Electrokinetic, adsorption, and flotation results indicate that when placed in a common solution, these two minerals interact significantly, with a corresponding strong influence on flotation using a physisorbed collector. Such behavior can have strong implications for flotation plant practice.

Jan 1, 1993

By Anthony Delvescovo, Gregory F. Aluce, Joseph A. Sopko, Lyle C. Smith

Construction of a 13m shaft through approximately 100m of water bearing soils and another 100m of bedrock was attempted using the Slurry Diaphragm Wall Method with a combination of deep dewatering wells. During excavation within the slurry wall, unexpected groundwater inflows occurred in a structure of loose silty sands. Artificial ground freezing was selected as a remedial method to seal the leaking slurry wall, and as a primary excavation support and groundwater control method for the 30m of overburden material below the base of the wall. Design of the ground freezing system required analysis of both the structural requirements of the unsupported soil, the frost effects against the existing slurry wall and the groundwater control in the area of the breech in the wall. These design procedures are summarized, and construction and excavation techniques and corresponding schedules compared in this paper. Advanced drilling techniques, ground freezing quality control and general contractor procedures for efficient shaft construction are discussed.

Jan 1, 1993

By Robert L. Bates

United States production of the industrial minerals, ahead of that of the metals since 1946, has shown a steady and rapid growth. By 1963, their value was more than twice that of the metals. Yet papers on the metallic ores continue to dominate the meetings of the Society of Economic Geologists and constitute nearly nine-tenths of the lead papers in Economic Geology. Most of the geological communication that does take place concerning the industrial minerals deals with high-value special-purpose minerals, which are comparable to the metallic ores in geologic complexity. The large-bulk rock products, which are growing fastest in production value, are characterized by relatively simple geology and by thousands of small producing firms, many of which do little or no geological work. The need for geological advice by this very large segment of the industry is bound to increase. In the meantime, a plea is made for more geological communication among those concerned with the industrial minerals of all varieties.

Jan 1, 1966

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By A. D. Davis, C. J. Webb

Brohm Mining Co.'s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February 1999 the Governor of South Dakota announced plans to request the US Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable groundwater reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2003

By Charles E. Joachim

Current Army tunnel destruction criteria (1) are based on limited nuclear-explosive (NE) and high-explosive (HE) test data. The PILE DRIVER (2) and HARDHAT (3) events investigated tunnel and support system response where yields were relatively large and tunnel diameter small compared to typical underground openings and localized stress fields of low yield weapons. Some limited tunnel destruction information was obtained from underground events of the PLUMBBOB and HARDTACK II Series (4). These events used access drifts which were designed to be self closing at the weapon point. The limited NE data are augmented by HE results from the Underground Explosion Test (UET) Program, a series of model and prototype-scale experiments in granite and sandstone (5). Weapon standoff distances (charge c.g. to tunnel wall) were at or near the maximum for major damage. Limited tunnel destruction was produced by a series of hasty and deliberate tests (6) on abandoned railroad tunnels in basalt. Additional HE data were obtained from model tests at the Waterways Experiment Station (WES) (7) using 2.1 MJ (2 lb) TNT charges and tunnel diameters varying from 3 to 17 cm (1.2 to 6.6 in). Recent laboratory scale HE experiments (8) conducted at the WES under the ESSEX program investigated the effects of tunnel diameter, standoff distance, charge confinement, material strength and to a limited extent, tunnel spacing and liner strength variations on tunnel damage. This paper summarizes the analysis conducted to develop predictions for the effects of low-yield nuclear weapons against tunnels and underground openings in rock.

Jan 1, 1979

By I. Tsolas

Sustainable development is becoming increasingly more important for the mining industry and therefore mining companies should be able to measure their progress towards sustainability. Greek Public Power Corporation (PPC) S.A. is a company which produces lignite in open cast mines in Western Macedonia and in Peloponnesos. The present paper uses operational data kindly offered by PPC S.A. to derive sustainability indicators by means of Data Envelopment Analysis for three large scale lignite open cast mines of PPC (i.e. Main Field, Kardia Field and South Field mines). It also examines three environmental parameters related to the contribution of these mines to sustainable development; namely, the annually produced volume of waste masses, the annually produced quantity of ash from the lignite combustion and the annual volume of pumped water. The calculated sustainability indicators were keeping constantly better during the last years of the different periods for each one of mines studied here, showing that the mines met their goals from both economic and environmental aspects during the last years of their operational periods studied. The contribution of open cast lignite mines studied here to sustainable development can be monitored by the derived indicators analyzing annual mine operational data. The derived indicators can serve as tools to detect where improvements can be made, though another potential use of these indicators can also be during the preparation of feasibility studies or environmental impact studies using necessary benchmarking data.

Jan 1, 2007

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By R. S. C. Rogers

A mathematical model is proposed as a general formulation for the analysis and simulation of once-through crushing machines. Methods are described which can be used to estimate parameters of the proposed model from experimental data, thus minimizing reliance on backcalculation. The applicability of the model is demonstrated in the analysis and simulation of laboratory and full scale double roll crushers, and with evidence given for a laboratory scale cone crusher. An extension of the model for closed circuit crushing is also described.

Jan 1, 1984

By Clair Murdock, David Heath

The 1,280 MW Sir Adam Beck II Hydroelectric Project was constructed in the1950s, at Niagara Falls, Ontario, Canada. The twin intake tunnels total over 17 kilometers in length and pass deep below the City of Niagara Falls. The tunnels were excavated using drill and blast methods, with a top heading and bench approach. The shot rock was loaded with electric shovels and transported to the five shafts with off-highway trucks. The tunnel muck was hoisted to the surface by skip and transported by truck to disposal areas. The volume of underground excavation for the 15.55 meter diameter tunnels and the shafts exceeds 3,500,000 cubic meters, then and now the largest underground civil works excavation by drill and blast in the Western Hemisphere. The lining required over 900,000 cubic meters of concrete. All of this work was completed in three years, remarkable progress, considering the technology of the day, comparing very well with the rapid excavation and tunneling methods of the twenty-first century. Big, fast, and deadly—at least 20 lives were lost in construction accidents.

Jan 1, 2007

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By B. Qiu, Y. Luo

The design of the predriven recovery room is not an easy task, because the stress distribution in the barrier pillar, standing supports, fender pillar and the immediate roof is changing as the longwall face approaches the predriven recovery room. An analytical approach is proposed to determine the stress distribution in the barrier pillars, fender pillars, standing supports and immediate roof of the recovery room based on the fracture mechanics approach. Based on the developed mathematical model, a stand-alone computer program has been developed to facilitate the required computations. The parameters such as overburden depth, recovery room width, mining height, shield and standing support capacities are incorporated into this program to access the feasibilities of predriven recovery room designs. Compared to the finite element method previously employed, this analytical approach offers the same, if not better, accuracy without requiring expensive computer hardware and software or specialized expertise.

Jan 1, 2012