Search Documents

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By M. Fornaro

A small size quarrying activity (3 different quarries with an overall production in blocks less than 10.000 m3/year) has been exploiting for a long time the ?Tonalite? deposit of Adamello-Presanella. In 1967, given the outstanding natural beauty of the area, a natural park has been established with the aim of preserving environmental quality and, at the same time, of providing a sustainable development to the area. Because of the potential impacts of a mining activity in such a context, a specific study has been recently carried out in order to define if and how the quarries could co-exist with the park, beyond the ?administrative results? of a classic environmental impact assessment. The paper deals with the process that drove to the conclusion that the activities are not ?a priori? incompatible with the aims of the park. In the opinion of the authors, a responsible quarry management, which must take inspiration from the care given to environment by traditional alpine productive activities (e.g. the use of water, of wood, and of the stone itself), and take advantage of modern technologies in terms of emissions and safety, can be considered not only compatible with the protected area, but even able to positively contribute to the protection of the land and environment (Barisone et al., 2001). A series of specific prescriptions, which have been adopted by the Park Authorities after this study, are also discussed in the paper: only the definition of suitable spatial and temporal limits, the adoption of effective technical practices and a strict control are considered to be able to drive this ?exceptional? activity towards the final goal of real sustainability.

Jan 1, 2007

By M. M. Veras, C. H. Sampaio, A. S. Young, D. Neto, C. O. Petter

"Due to new technological developments, automatic sensor based sorting has made progress within industrial minerals, precious metals, diamond, and coal mining in recent years (Lessard et. al. 2016). In order to re-introduce the technology to other mining sectors, this research discusses its application to iron, manganese, and zinc ores through test works performed by the authors. These test works were performed using Dual Energy X-ray Transmission (DE-XRT) sensor technology. In each case, pre-concentrations of the ore were created demonstrating the possibility to reduce waste material, energy costs, and water consumption while improving product quality of the ores. INTRODUCTION Sorting of mining ores is as old as mining itself (Salter, 1991). Sensor based sorting applications in coal mining began as early as the late 19th century (Louis 1928). New sensor technologies were developed and implemented sequentially for uranium, nickel, coal, and gold mining (Refining, 1949, Rose et al, 1950, Bloomfield et al, 1966, Clayton et al, 1987, Robben and Mosser, 2014). While these sensor technologies were developed decades ago, computational capacity to keep pace with the vast amount of information required utilizing the sensor technology did not arrive until recently (Lessard et. al., 2016). The sensor based sorting (SBS) process was effectively described by Salter and Wyatt in Minerals Engineering in 1991, and Wotruba and Harbeck in 2010 in the Ullmann’s Encyclopedia of Industrial Chemistry under Sensor Based Sorting. Both descriptions include the following key steps: 1. Presentation of the material or particles. 2. Examination or detection of the material or particles. 3. Processing or analysis of the data generated. 4. Physical separation of the material or particles by external means. Effective presentation of the material or particles is achieved when the sensor is capable of identifying each particle individually. This step requires that each fragment of the material be isolated, and it often involves acceleration of the material fragments by chute or mechanical means, as well as the spreading of particles by vibratory feeders (Salter and Wyatt, 1991, and Wotruba and Harbeck, 2010). The isolated particles typically are conveyed into an area wherein they are subjected to electromagnetic irradiation (except in cases of some radioactive ores), either in the form of x-ray, visible light, infrared, or other energies. A wide range of applications for sensor based sorting exists in the literature. The majority of applications fall into one of two camps, (1) pre-concentration of mineral ores, or (2) characterization of the material during processing (Buxton and Benndorf 2013). While there is much to be gained from in-line material characterization and the resulting control both of quality and processing, this article focuses primarily on the camp of pre-concentration of mineral ores."

Jan 1, 2017

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By K. A. Natarajan, J. M. Modak, B. Saha

Nonliving waste biomass consisting of Aspergillus niger attached to wheat bran was used as a biosorbent for the removal of copper and zinc from aqueous solutions. Copper and zinc uptake by the biomass obeyed Langmuir isotherms. The binding capacity of the biomass for copper was found to be higher than that for zinc. The metal uptake, expressed in milligrams per grain of biomass, was found to be a function of: •the initial metal concentration (with the uptake decreasing with increasing initial concentration), •the biomass loading (with the uptake decreasing with increasing biomass loading) and •pH (with the uptake increasing with increasing pH in the range of L5 and 6.0). The metal uptake was significantly affected in the presence of a co-ion. The uptake of copper by the biomass decreased in the presence of zinc and vice versa. The decrease in metal uptake was dependent on the concentrations of metals in the two-component aqueous solutions. The effect of copper on zinc uptake was more pronounced than the effect of zinc on copper uptake.

Jan 1, 1997

By D. E. Hart, A. R. Walsh, Derek Maishman

In order to safely construct a ventilation and escape shaft through saturated overburden into an operating mine, artificial ground freezing and raise boring were combined for the first time on a project in the U.S.A. at Georgia-Pacific's Kentwood Mine in Grand Rapids, Michigan. Previous to drilling a pilot hole 206 feet deep into the mine, a 20 foot diameter cylinder of soil 140 feet deep was totally frozen. Before termination of the freezing operation, the pilot hole was reamed to 9 foot diameter and a 7 foot inside diameter hydrostatic steel liner was grouted in place.

Jan 1, 1991

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By B. Bergmark, O. Guyot, A. Broussaud, C. Bouché

The Boliden Aitik concentrator in Sweden processes 2,000 t/h (2,200 stph) of low-grade copper ore. The plant consists of five grinding lines that feed four bulk-flotation banks with a scavenger-concentrate regrind mill und a column cleaner circuit with a regrind mill. The authors installed a model-based expert optimizing control system to maximize copper recovery in the bulk-flotation circuit while maintaining an appropriate copper grude in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent- addition rates. It combines the power of a dynamic population-balance model that estimates mineral liberation in each stream, an optimizer that computes appropriate set points and a rule-based module that implements the strategy. The benefits have been evaluated over a period of three months. The model-based expert optimizing control system generates a measurable increase in copper recovery, around 0.5%, and an optimized bulk-concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 2000

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By G. Hilson

The exact application of sustainable development in the mining and minerals industry has precipitated considerable debate in recent years. Since the publication of the Brundtland Commission?s Report, Our Common Future, numerous attempts have been made to define sustainable development in the mining context. The inability of the Brundtland Report to outline an effective sustainability framework, combined with its contention that no single blueprint for sustainable development exists, has prompted many academics and practitioners to provide viewpoints on the application of sustainable development in the mining and minerals industry. This paper provides an overview of the many groups of assessments made of sustainable development in the mining industry. Sustainability assessment and reporting for this industry sector using indicators are also addressed.

Jan 1, 2003

By Kristin Hemlein

Mining project development, permitting, environmental regulatory and compliance issues in Uzbekistan and the CIS are every bit as complex as those in the western world. The vast array of environmental permitting, monitoring and reporting regulations for mine project development and operation in the CIS are based on existing Soviet environmental regulations and policies which have remained in place after these countries gained independence from the former Soviet Union. The approach to mine project permitting in the CIS differs from the western world. Similar pre- feasibility, baseline data collection, and environmental monitoring requirements allow the project proponent to coordinate preparation and submission of documentation to support project permitting for Uzbek regulatory requirements with environmental requirements imposed by financial institutions and western environmental compliance structures. Implementation of generally accepted western environmental best management controls and monitoring into mine design, construction, and operation will not, however, ensure automatic compliance with Uzbek environmental regulations. Uzbek environmental compliance requirements that differ from western requirements include: 1) development and maintenance of an environmental database constructed specifically to address annual, biannual and quarterly statistical reporting requirements for emissions of "environmental pollutants" from the facility into air, surface water, ground water and soil; 2) preparation and submittal of specific permits for water utilization, hazardous waste storage and disposal, landfill construction and operation, and stack emissions inventories; and 3) procurement of approvals from the Uzbekistan State Committee for Nature Protection (generally analogous to the US Environmental Protection Agency). This paper outlines and summarizes the regulatory requirements for mine site permitting and the procedures for environmental monitoring and reporting during mining operation in Uzbekistan and the CIS.

Jan 1, 1997

By Robert G. McLusky

Since 1998, environmental extremists have waged war with the central Appalachian coal industry in West Virginia and Kentucky. In particular, they have filed three lawsuits challenging the legality of excess spoil ‘valley fills’ under CWA, NEPA and SMCRA: 1) Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D.W.Va. 1999), rev’d. 248 F.3d 275 (4th Cir. 2001); 2) Kentuckians for the Commonwealth v. Rivenburgh, 204 F.Supp. 2d 927 and 206 F. Supp. 2d 782 (S.D.W.Va. 2002), rev’d. 317 F.3d 425 (4th Cir. 2003); and 3) OVEC v. Bulen, 2004 U.S. Dist. LEXIS 12690, July 8, 2004; OVEC v. Bulen, 2004 U.S. Dist. LEXIS 16078, August 13, 2004.

Jan 1, 2005

By D. Bizier, B. H. Gardner, Y. P. Wang, S. Serata

As part of an ongoing effort to develop more cost-effective and “user friendly” hardware for geomechanical measurements required for underground mine design, Serata Geomechanics, Inc. (SGI) has investigated the potential of borehole pressure cells (WCs) for in situ measurement of stress states and continuous monitoring of changes in ground stress. In particular, because of certain advantages gained thereby, WCs utilizing an elastomer, instead of metal (e.g., copper), for the skin of the pressure cell have been developed. A data analysis technique for determining ground stress state directly from BPC data has been developed. This technique has been tested for salt ground through both in situ applications and computer simulation analysis of the BPC/borehole boundary interaction. This paper discusses the data analysis technique, the results of field and computer simulation testing of its validity, and evaluates the advantages of elastomeric BPCs in relation thereto. It utilizes field data from recent elastomeric BPC applications in the salt mine at Goderich, Ontario operated by the Sifto Division of Damtarn Inc.

Jan 1, 1986

By Fan Yang, Meigui Yi, Lan Xiang, Zhuoying Yang

This paper reported the calculation of the reaction heat in titanium-bearing blast furnace slag (abbreviated as TBFS)-H2SO4 system based on estimation of thermodynamic data of CaTiAl2O6 by mechanical mixture model. The thermodynamic analysis indicated that CaTiAl2O6 was more stable than the corresponding ternary oxides as CaO·TiO2, CaO·Al2O3, and Al2O3·TiO2. TBFS-H2SO4 system was highly exothermic since all of the reactions involved in the system were exothermic. For example, the increase of temperature from 25 to 200°C led to the increase of the release of the reaction heat in TBFS (100.0g)-H2SO4 system from 181.28 to 189.73kJ. Eighty-five to 90%of the reaction heat in TBFS-H2SO4 system was contributed by the reactions among CaTiAl2O6, CaTiO3, CaMgSi2O6, and H2SO4.

Feb 1, 2021

By K. V. S. Sastry, A. J. Hunt, K. D. Lofftus

Sol-gel processing is rapidly becoming an important process for producing such advanced materials as high activity catalysts, fiber optics and ceramic precursors. These materials can be tailor made with properties unique to sol particles as well as the gel aggregates by controlling production of the sol, the formation of the gel, and the removal of the interstitial fluids. This paper presents colloidal and kinetic principles of sol generation and gel formation. Hydrolysis of alkoxides provides the best means of controlling sol production and electrostatic stabilization enables the formation of the most homogeneous gels. Gelation occurs by hierarchial aggregation which produces inhomogeneities much larger than the sol particles. Colloidal and kinetic principles can be applied to reduce the size of the inhomogeneities and obtain high performance transparent insulation and new ceramic composites.

Jan 1, 1990

By C. A. Fleming, C. J. Ferron, P. T. O'Kane, D. B. Dreisinger

The platinum group metals (PGM's) are typically recovered by flotation, smelting of the flotation concentrate to matte, and matte leaching. Concentrates too low grade to be processed economically by the conventional process require a new treatment route. PLATSOL, a new pressure leach process, was developed for the Northmet deposit and dissolves in one step base and precious metals (PGM's and gold). Various options exist to recover all pay metals from the leach liquor. The preferred option to date involves a solid-liquid separation, followed by sulphide precipitation of gold and the PGM's, and copper solvent extraction using commercial solvent extractants. This paper briefly summarises the process and the effect of the main leach parameters. Application of the PLATSOL process to various feedstocks is also presented.

Jan 1, 2000

By D. T. Maiers, P. L. Wichlacz, P. A. Pryfogle, J. H. Wolfram

The effects of metal solution concentration, biomass density, length of exposure time, and pH were determined for biosorption of molybdenum (Mo) and chromium (Cr) by three organisms. Results indicate that it is possible to sorb Mo and Cr from dilute solutions. Differences were observed in the abilities of an organism to sorb Mo and Cr as well as among respective abilities of the three microorganisms. This suggests an inherent selectivity of the organism which may afford the means to control a sorption-based process. Results also indicate that the metal sorption abilities of these microorganisms depend on duration of exposure, biomass density, solution pH, and the metal concentration of the solution. Each of these parameters suggests an additional means of controlling the sorption process.

Jan 1, 1989

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Because of increasing production of fine coal during mining over the past century and because of inefficient fine-coal recovery technologies, a vast reserve of high-quality coal now exists in refuse ponds. A novel finecoal circuit, consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column, was evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,170 kJ/kg with 60% mass yield. Results from the treatment of two refuse pond materials are presented in this paper.

Jan 1, 2002