Search Documents

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By Michael J. Hannan, Thomas F. Torries

The nature of industry structure is examined and the structure of the aluminum, copper, lead and zinc industries are described by the use of factor analysis. Capacity is defined and the relationship between industry structure and capacity utilization is examined. It is demonstrated that excess capacity is possible in industries with competitive or monopolistic characteristics, but the effects of the overcapacity are vastly different in the two cases. In a competitive industry, cycles of overcapacity with attendant fluctuating prices are expected. A change in industry structure from monopolistic to competitive characteristics over time causes profits and economic rents to be transferred from the producer to consumers of the mineral.

Jan 1, 1989

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By John W. Rushton

Maintenance and inventory are usually the last items considered in mine development. They need to be addressed properly and early. The micro-computer brings sophistication within the reach of even the smallest mines. Maintenance and inventory programs, if properly installed, will reduce costs 15 to 25% and allow management time to address the mining and metallurgical problems at start up. Shops and warehouses are rarely designed properly. Large engineering firms spend 5 to 20 times more than is necessary for first class facilities. There is an optimum design, size, and layout. Take the time necessary to assure you get the right people, programs, and facilities in that order. Maintenance, inventory, and inventory control must be addressed early if a small mine is to have a chance at optimizing costs during the first two years of operation. This is hard work and is usually put on the back burner until the mine is in some degree of trouble. Hiring an experienced maintenance superintendent is important but it is not the complete solution. Maintenance systems, design of facilities, and use of computers are not skills that maintenance people usually have. In addition, the work of ordering spare parts and working with erection people is a full time job and any maintenance people on site during construction are quickly recruited. The end result is that few mines start up with an adequate Maintenance or Inventory System in place. The months, and in some cases years, that the mine attempts to operate without a system are both painful and expensive. Designs of successful integrated maintenance and inventory programs are virtually 100% supported with some outside assistance. Our system is the approach that we are most familiar with and this paper will isolate how Rushton International would go about setting up systems and designing support facilities. Micro-computers are the only way for a small mine to go. ~ini-computers cost more originally and operating costs are many times higher than even the most sophisticated micro system. Micro- computer software is developed further and recent advances in hardware makes medium priced units equal to most mini's in RAW COMPUTER POWER. Mines in general, and especially small mines, have no need for main frame power. MAINTENANCE A good maintenance program has: 1. Equipment Master List a. Equipment Detail Reports 2. Work Order and Backlog Control Program 3. Component Control Program 4. Tire Program 5. Wear Materials Program 6. PM Control Program 7. Maintenance History Program 8. Performance Program We also track miscellaneous items such as MSHA training and inspections, timekeeping, etc. Rather than going through the program step-by-step, it makes more sense to go through a typical Maintenance Day and show how the programs are used. The first thing maintenance supervision needs to know is "how we are doing." We

Jan 1, 1987

By Shingo Morimoto, Toru Sasaki, Masato Shinji

"1. INTRODUCTIONTunnel face stability is one of the most important consideration in New Austrian Tunneling Method. In general, if all of the material properties of ground can be obtained through the field investigations, the tunnel face behavior can be predicted using numerical simulation prior to tunnel construction. However, estimating the safety of a tunnel face is difficult, especially in cases where the ground is very weak such as in an urban area.In this study, numerical analyses of tunnel excavation in very weak ground conditions, such as a low cohesion and low internal friction angle, were carried out. The relationship between the average shear strain distribution on the tunnel face and the overburden was analyzed. This relationship estimates the shear strain of the tunnel face relative to the critical shear strain obtained by the ground properties. The critical shear strain was defined as an allowable value for the maximum shear strain. We proposed the allowable overburden as tunnel face stability index (TFI) that satisfies the critical shear strain criterion of ground. Finally, a design chart of the allowable overburden for various cohesion values and friction angles of ground was created. This chart is useful in the preliminary tunnel design stage to judge the necessity of additional counter measures against normal tunnel support design.2. WEAK GROUND MODELING AND ANALYSIS PROCEDURE2.1 Setting material propertiesWith reference to a past study1), the material properties were adopted on the basis of material properties in the standard worst rock classification case called “DII”2) for standard support pattern of weak ground in Japan. The typical material properties for “DII” are listed in Table 1. In addition, Fig.1 shows the distribution of the representative weak ground according to cohesion and internal friction angle. When the internal friction angle is relatively high and the cohesion is weak, the ground is categorized as sandy ground. Furthermore, when the internal friction angle is low and the cohesion is strong, the ground is categorized as clayey ground."

Jan 1, 2016

By G. W. Riley, D. E. Pickett

HINDERED SETTLING CONCENTRATION In the free settling of mineral particles in a liquid, the falling particles are at a distance from each other so that no particle is affected by its neighbor. In hindered settling, the concentration of particles is sufficiently high so that each particle is affected by its proximity to other particles in the suspension. Richards and Locke86 have described the hindered settling phenomenon as the condition “.. where particles of mixed sizes, shapes and densities in a crowded mass, yet free to move along themselves, are sorted in a rising current of water, the velocity of which is much less than the free-falling velocity of the particles but yet fast enough so the particles are in motion." This is the condition normally encountered in mineral con¬centration processes. The well known Newton equation for free settling of coarse (ap proximately +10-mesh, 1/16-in. or -- 2000-µm) spherical particles is:87 where v," is free settling velocity, cm/sec; p' is density of the fluid; p is density of the particle, g/cm3; d is particle diameter, cm; g is acceleration due to gravity, cm/sec2; and Q is coefficient of resistance, dimensionless, ~0.4. For the settling of fine spheres in water (approximately 150 mesh or 100 µm) the equation of Stokes pertains:87 where µ is viscosity of the fluid in poises and the other symbols have the same meaning as those in Eq. 1. For particles whose size lies between about 10 mesh (--2000 µm) and 150 mesh (100 µm), their settling velocity can be determined from experimental data. These data are available in convenient form in the text by Taggart88 based on the original work of Richards. Alternatively, a Reynolds number-coefficient of resistance plot may be used to determine the settling rate of such particles.87 The settling rate of spherical particles under hindered settling conditions can also be calculated from Eqs. I and 2 by replacing p', the density of the fluid, by p" the apparent density of the suspen¬sion. The concentration of particles in the fluid thus imparts an appar¬ent density to the composite fluid or suspension greater than that of the liquid alone, resulting in a buoyant effect on the larger particles. Particle shape affects the settling rate of both coarse and fine particles. The general effect is to reduce their settling velocities and the effect is greater for coarse particles and for those settling under hindered settling conditions than for fine particles or free settling ones. For two particles of differing densities but settling at the same velocity under Newtonian conditions, the ratio of their diameters from Eq. 1, called the free settling ratio is: where L signifies the lighter particle and H, the heavier particle. Under Stokesian conditions the exponent would be 0.5. For hindered settling conditions the fluid density p' is replaced by the apparent density of the suspension, p", to obtain a generalized equation for the hindered settling ratio: assuming both particles settle in approximately the same regime. The free settling ratio as given by Eq. 3 has been called by Taggart88 the "concentration criterion" and is used to predict the effectiveness of any gravity concentration process (see Introduction to this section). Based on Eqs. 3 and 4, if two particles of densities pH and p,, settle at the same velocity, the diameter of the lighter particle will be larger than that of the heavier particle. For example, in the case of galena (pH = 7.5) and quartz (pL = 2.65) settling in water (p =1.0) under free settling, Newtonian conditions 3.9. Thus, a quartz particle nearly four times as large as a galena particle will settle at the same velocity. Any quartz particle just slightly less than four times the diameter of the largest galena particle may be separated from it. Under hindered settling, Newtonian condi¬tions in a suspension where p" = 1.65, dL/dH = 5.85 or any quartz particle just slightly less than about six times the largest galena particle may be separated from it. Reference to Eq. 4 indicates that a superior separation between two minerals of differing densities is favored by: (1) coarse particles settling under Newtonian conditions, (2) a large difference in (pa - PL), and (3) separation under hindered settling conditions where p" is high. Of course, there are practical limits to increasing p" excessively because at very high percent solids suspen¬sion fluidity would be lost and the hindered settling separation process defeated. Examples of hindered settling separators are the Dorrco-Fahren¬wald sizer,89 the Rheolaveur box 90 the Spitzkasten,89 and the Willoughby washer.91 These devices make a mineral separation on the basis of both specific gravity and size and all of them are essentially obsolete except for the Dorrco-Fahrenwald sizer and similar devices which still find application for the removal of coarse particles from a much finer particle assemblage and for preconcentration ahead of shaking tables. However, nearly all gravity concentration processes (jigs, tables, flowing film concentrators, heavy media separators) and many sizing devices (sizing classifiers, clarifiers, thickeners, hydrosepa¬rators) make use of the hindered settling phenomenon during the separation of particles. JIGGING Introduction In jigging, a mixture of ore particles, supported on a perforated plate or screen in a layer or "bed" with a depth many times the thickness of the largest particle, is subjected to an alternating rising and falling (pulsating) flow of fluid with the objective of causing all

Jan 1, 1985

By D. R. Schricker

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment.

Jan 1, 1990

By P. L. Stavenger

Principles of Operation and Mechanical Features General Mechanical Description Sieve-bend screens are high-capacity screening devices which utilize stationary, concave, wedge-bar screening surfaces. A complete sieve bend is comprised of a feed distribution chamber, a structure for holding the screen surface, and collection chambers or chutes for oversize and undersize materials. In devices used for metallurgical practice, provision is usually made for reversal of the direction of flow over the surface, either by rotating the surface or by changing the feed nozzle position. The size of the unit varies in height from 5 to 8 ft, and in width from 2 to 8 ft. The orientation of the wedge-bar surface is such that the slots between the wedge bars are perpendicular to the flow of feed material over the surface. The feed distribution means is arranged such that the flow of liquid suspension is distributed evenly and tangentially over the width of the screen surface. A variety of means are used including simple gravity weir feeds, long slotted nozzles, and a multiplicity of round nozzles. A typical gravity-fed weir type nozzle is shown in Fig. 18. Most sieve bends are fed with gravity feed in such

Jan 1, 1985

By M. S. Seehra, V. Suresh Babu, R. S. Pandurangi

Different mixtures of the three polymorphs of silica viz. quartz, cristobalite and tridymite are analyzed by x-ray diffraction (XRD) and their IR spectra are investigated by photoacoustic spectroscopy. It is observed that XRD provides a higher resolution to distinguish between the three polymorphs in a sample than IR spectroscopy. In the latter, a sharp band near 617 cm-1 is characteristic of both cristobalite and tridymite. A mine dust sample is quantitatively analyzed by XRD and it is shown to contain illite, quartz, kaolinite and calcite.

Jan 1, 1991

By G. M. Swinkels

It is generally accepted, that oxygen is a necessary reagent for the flotation of galena with xanthate. Recent measurements have shown (1) that under plant conditions oxygen may be in a short supply to the extent that it limits the rate of flotation. Thus, it becomes important to define the exact role of oxygen and establish a model for the rational design and control of flotation separations, involving oxygen as a reagent. All theories or, the flotation of galena assign oxygen the role of an oxidant. However, they disagree on a number of questions: 1) Is the galena or the xanthate being oxidized? 2) Is a lead dixanthate or dixanthogen the actual collector? 3) Is the oxidation process in which oxygen participates of a chemical or an electrochemical nature? The last question arises from the observation (2) that an anodic bias as well as oxygen will make a galena surface hydrophobic in the presence of xanthate. Theories which are based an the premise that the influence of oxygen is of an electrochemical nature offer elegant models of galena flotation. However, full advantage has not been taken of available electrochemical techniques to discriminate between theories and this is the area towards which this research has been directed (3).

Jan 1, 1970

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By J. C. Yingling, R. J. Sweigard, S. T. Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty inherent in the factor-of-safety (FS) predictions for soil slopes in which there is an incomplete knowledge of the spatial distribution of soil properties. A case study that considers a natural clay slope in Canada is presented. The sequential-indicator simulation technique was used as a means of generating a series of spatial maps of the soil properties at the site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. FS determinations were made for each simulated map using the simplified-Janbu approach. In using this approach, computations are performed using a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the FS distribution conditional to the type, position and value of existing site-characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1996

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: 'We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today's level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By Gerard P. Hand

The use of graphite in industrial applications is one of the oldest in the world. Yet, it is one of the fastest-changing technologies today. Graphite was first used centuries ago in developing writing instruments and as a raw material in crucibles used in melting metal. Today, graphite is used in some of our most demanding industries. These include aerospace, electronics and automotive applications. Graphite usage has historically been split between the natural and synthetic forms. Figure 1 shows the breakdown of natural graphites and synthetic graphites used. The usage of natural graphites and synthetic graphites is split fairly evenly, although the applications are quite different. Figure 2 shows the breakdown of applications using natural graphite. The largest application is the refractory industry. This includes refractory brick and plastics, crucibles, shrouds and other refractory parts. This main application uses roughly 50% of all natural graphite. The refractory industry is an important application for natural graphite. However, the refractory markets have been struggling for several years. As demonstrated in Fig. 3 (Semler, 1996), the production of refractories in tons per year has declined by more than 32% during the last 25 years. Refractory prices have actually risen on a dollar per ton basis during that same period as the product mix has shifted to the value-added side. Raw material and production cost increases, inflation and other related costs have kept profitability at low levels for the industry. Furnace linings that once lasted 1,000-2,000 heats now last 8,000-12,000 heats. This means that tonnage requirements have gone down and quality requirements have gone up for graphite suppliers. Therefore, new opportunities and applications must be developed if the graphite industry is to grow. Synthetics are the other major forms of graphite. There are two forms of synthetic material currently used. One is the traditional type. It is made from the turnings of graphite electrode production. The second was developed in the mid-1970s in response to a shortage of conventional synthetic graphite. This occurred by a breakthrough in thermal technology. This new technology purifies, desulfurizes and graphitizes petroleum coke on a continuous basis at temperatures of more than 2,500° C (4,532° F). This product is called desulfurized petroleum coke (Desulco). It now accounts for about half of the synthetic type material used in the United States. Figure 4 shows the breakdown in the use of synthetic types of material by application. The largest requirement is for use as a carbon addition in iron and steel. This is followed by alkaline batteries and friction materials. Current technological opportunities New opportunities for graphite products are now being developed. These new areas are made possible due to the advances in graphite thermal technology. The ability to purify and modify graphite and carbon products is the key to future growth in the graphite industry. New, higher-purity, more consistent graphite products are leading to enhanced performance in current applications. They are also opening the door to new applications.

Jan 1, 1997

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987