Search Documents

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By J. Schleifer

On short term, planning techniques require more details to ensure feasibility, giving importance to operation constraints and use of available resources. In GUEMASSA (Morocco), the ore mass is mined by cut-and- fill method. Correct organization requires to forecast a few weeks ahead the schedule of blocks to be mined, in order to respect ore quantity and grade constraints. While operating constraints are tackled, feasibility is assumed with an average production capacity suggesting that resources will be available. In ST-SALVY (France), scheduling operations is not possible if not considering account resource allocation. In any stope within the vertical vein zinc deposit, the cut-and-fill method enables to mine each horizontal slice according to various strategies, de- pending how to use manpower and equipment, and selecting among predefined scenarios known as realistic. For KOFFIEFONTEIN (South Africa), the kimberlite pipe is mined by a sub-level-stoping method. To achieve the production target, precise organization over one month is obtained, using on& resources when available and respecting all mining rules. This combined operation scheduling and resource allocation is called sequencing. While following the BONANZA concept, providing a planning- retrieval process, sequencing offers more. Very detailed, it is possible to check the impact of resource parameters and mining rules. The sequencer, like a simulation platform, enables expertise. Each sequencer must be tailor-made to fit to each specific mine. The next challenge is to produce a generic environment.

Jan 1, 1996

By John H. Bassarear

How best to grind? This article compares conventional crushing and grinding circuits to semiautogenous circuits, reviews recent installations of each circuit, and describes seven methods of using autogenous or semiautogenous techniques. In addition, steel and power consumption data are reported and benefits of a dedicated digital computer are discussed. Size reduction is the most expensive operation in most mills. Crushing and grinding are usually the greatest part of capital costs. They often make up 60-70% of total mill operating costs. Picking the proper crushing and grinding method must, therefore, be done with great care, so the best circuit is chosen. In the past 10 years, there has been a strong trend toward using autogenous or semiautogenous grinding in mills throughout the world. Autogenous grinding is favored when the ore is quite competent and a fine grind is needed. Semiautogenous grinding is applied when fine crushing could cause severe problems or when ore varies in hardness or competency. The taconite iron ores of northern Minnesota fit the description for an autogenously ground ore and many are successfully ground that way. Most im¬pressive are the nine lines of 11 x 4.9 m (36 x 16 ft) mills powered by 9 MW (12,000 hp) motors at Hibbing Taconite. Porphyry copper and molybdenum ores fit the description for semiautogenous grinding. Recent installations include Highmont in British Columbia, Canada, and Quintana in New Mexico. Sampling Many mills have been built based on inadequate sampling data or insufficient tests. With the cost of many mills exceeding several hundred million dollars, it is mandatory that geologists, mining engineers, and metallurgists work together to prepare representative testing samples. Simple, repeatable work index tests are usually sufficient for rod and ball mill tests. However, pilot plant tests on 50-100 t (55-110 tons) of ore are frequently necessary for autogenous or semiautogenous mills. Preparation and selection of the test sample is of utmost importance. Procedures for autogenous and semiautogenous mill pilot plant tests are relatively simple for those experienced in running them. Reliable and repeatable results can be obtained if simple, fundamental procedures are followed. The accompanying figure shows a typical conventional crushing-grinding circuit with three stages of crushing followed by ball mills or a rod mill-ball mill combination. This flowsheet is typical of many mills that have been built throughout the world. Also shown is a typical semiautogenous (SAG) circuit with feed coming directly from a primary crusher, and the semiautogenous mill product going to the separation process. Many similar semiautogenous circuits are built today because they are simple and flexible, lend themselves readily to high tonnages, and usually cost less to build and operate. With some ores, it is possible to send mine-run ore directly to the semiautogenous mill, eliminating the need for a primary crusher, as at Benquet's Dizon mill in the Philippines. An autogenous or semiautogenous circuit, as the name implies, uses the ore itself to assist in the grinding process. Generally, for this type of circuit, the ore must be competent so large ore chunks can be used to grind smaller ones. If ore alone is used, then the circuit is autogenous; but if balls are added to supplement the charge, then the circuit is termed semiautogenous. Ore competency is not always a criterion, to break up large pieces and wash away cementing material. Autogenous and semiautogenous mills have been very successful on relatively soft uranium ores where the values are frequently found in the material that cements together the sandstone grains. Autogenous Circuits When an ore is hard and competent, it is always possible it might make good "pebbles" that could be used for fine grinding media. Seven methods have been tried using combinations of autoge-

Jan 6, 1982

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By Camillo Premoli

Namibia is one of Africa's newest nations. A German colony until 1915, it then became a South African protectorate until 1990, when it gained independence after an armed struggle that lasted more than two decades. However, no trace of past bitterness can be found today in the capital, Windhoek, or in the countryside. Namibia is now one of the safest parts of Africa. Namibia's industrial base and infrastructure have been untouched by war. Swapo, the ruling party, has embarked on a successful policy of reconciliation and economic development. The GNP per capita is a surprising $1500 (from the World Bank), one of the highest in Africa. Namibia's population stands at 1.3 million, including about 100,000 whites. Namibia is a very sparsely populated country (1.7 inhabitants per km2). About 70% of the people are farmers. Namibia has a surface area of 824,232 km2 (318,261 sq miles), about the size of France and Germany combined. The semi-arid climate and generally flat morphology make the country well suited to mineral exploration. About 40% of the country presents abundant rock outcrops. The rest is buried under the Kalahari sands. However, this cover in most of the country hardly exceeds 200 m (655 ft), and Australian technology has shown that large mineral deposits (Roxby Downs) can nowadays be found at even greater depths. Mining is Namibia's largest industry. In 1991, it accounted for 22% of the country's GDP, about 70% to 80% of its exports by value and 25% of internally generated government revenues. The Ministry of Mines and Energy (MME) is responsible for formulating and implementing national mineral policies. This agency has recently introduced legislation aimed at encouraging new and long-term investment in the mineral sector. The variety of Namibian mineral resources, both metallic and nonmetallic, is rivaled by few countries worldwide.

Jan 1, 1994

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Openpit mining (prestripping) began in 2010 and full production commenced during 2011. The openpit mines feed both a sulfide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp Inc. Peñasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals.As a consequence of lower grade ores expected with advancing mine life, Peñasquito is facing a declining metal production profile. To maximize returns and asset value, plant modifications, including the addition of a carbon prefloat circuit and a pyrite leach circuit to improve recovery, are currently being undertaken. This carbon prefloat circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Peñasquito operation. The addition of the carbon prefloat circuit was also a key driver in allowing the Chile Colorado openpit to be developed.These conditions alongside Goldcorp’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this article and include improvements in geomodeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 7, 2018

By James J. Guesk, Robert W. Reisinger, Timothy C. Richmond

A high-altitude (2,900 m [9,500 ft]) historic underground copper mine in Wyoming is discharging copper-laden water with a neutral pH into an otherwise pristine creek. The Wyoming Abandoned Mine Land program is reclaiming the site under a CERCLA deferral agreement. The clean-up goal is to reduce copper in the mine discharge so that the creek can eventually support a trout fishery. A pilot-scale passive treatment test utilizing sulfate-reducing bacteria has been conducted at the site beginning in summer 1997. Test results show significant reduction in copper concentrations in near-freezing mine water at flow rates ranging to 19 liters per minute (5 gpm)

Jan 1, 2000

By George H. Schnakenberg

The application of automation and robotic technologies to coal mining equipment at the face offers improvements in worker safety and efficiency. The evolutionary introduction of autonomous, intelligent machines to perform the most hazardous tasks in underground coal mines may become a reality within the next 10 to 15 years. The US Bureau of Mines Advanced Mining Systems research program is developing the technology necessary to achieve this goal. This program consists of both core and applications re¬search that focus on the fundamental issues of sensor-based, computer-assisted, machine control technology. In the near term, the research is directed specifically to the computer-assisted control of present-day underground equipment. The immediate effect will be relocating equipment operators to a nearby area of safety. It is being performed in a manner that can make incremental improvements in safety and efficiency. The research is being performed closely with private, government and academic researchers in the miring, space, armed forces and factory automation and robotics research areas. It is a mixture of basic research, applied research and the application and adaptation of existing technologies from a multitude of sources.

Jan 1, 1990

By C. W. Matthews

Introduction Screening is an art, one of the oldest in the process field today, and one of the most widely used in our present age. Screening is being applied to an ever-increasing number of assignments, in an ever-expanding circle of industries. Screening is defined precisely as a mechanical process which accomplishes a separation of particles on the basis of size and their acceptance or rejection by a screening surface. Particles are presented to apertures in a screening surface and rejected if larger than the opening, or accepted and passed through if smaller. Screens are machines with screening surfaces used to classify materials by size. The screening surface is the medium containing the apertures for the passage of the undersize material. Screens are put to many uses - size separation, dewatering, desliming, media recovery, scalping, trash removal, washing, dedusting, conveying, concentration, and many combinations of these functions. It is interesting to note that screens are used for handling commodities

Jan 1, 1985

By D. Legg

This is the first in a series of studies commissioned by the European Environment Agency that aim to raise awareness of the use of economic instruments and assess their effectiveness. The emphasis is on sharing good practice and increasing knowledge and understanding across European countries in this emerging policy area. A methodology for evaluating the effectiveness of economic instruments has been developed and this will examine whether the inclusion of economic instruments in complex policy packages can improve the overall performance, particularly as a prevention tool in terms of resource use and waste generation The focus for this initial study is the use of aggregate taxes in four EU countries which include the Czech Republic, Italy, Sweden and the UK so that a range of experiences (e.g. geographical, political etc.) can be included. The findings will be used to inform and influence future policy development in other EEA countries. The methodological approach is divided into two main sections: - Technical analysis, which covers quantitative and qualitative analysis. - Process design, i.e. who should be involved when, where and how. Process design is essential if the full learning benefits are to be gained from the technical analysis, which is the ultimate objective of these evaluations.

Jan 1, 2007

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By Jorgen Elbrond, Xiaoli Tang

In this paper we apply continuous-time option pricing theory (Dixit 8 Pindyck 1994) to show how to obtain an optimal investment rule for a mining project which requires sequential in- vestments. The application per se is to some extent very simple. The main purpose of the paper, however, is to draw the attention of mining people to how the option pricing theory may be used to capital investment decisions. This topic in economics is quite new but is attracting a lot of attention.

Jan 1, 1996

By G. Michael Lloyd

The term phosphate beneficiation often conjures up visions of processing technologies that physically separate the phosphate rock from some impurity and do not result in a change in the chemical nature of the phosphate rock. However, when we consider hydrometallurgical processing as a phos¬phate beneficiation technique we have to include all chemical treatments that convert phosphate rock into a more useful product. With most of the phosphate rock mined being used for fertilizer pro¬duction, the best known and most widely employed hydrometallurgical process is wet process phospho¬ric acid manufacture. In general, all phosphate rocks are so insoluble that there is no physical treat¬ment that will allow the phosphate content to be used by vegetation in a timely manner. However, after chemical treatment, 100% of the phosphate is readily available for vegetation nutrition. If there is a chemical beneficiation process that could be considered the standard method of treat¬ing phosphate rock it would have to be the wet pro¬cess for phosphoric acid production. In this process finely ground phosphate is reacted with sulfuric acid to give phosphoric acid and phosphogypsum. The phosphogypsum crystals are removed from the phosphoric acid solution and discarded; the phos¬phoric acid is further processed to give the finished fertilizer product. The primary reason that this pro¬cess was adopted so widely is because the phosphogypsum solid that is formed can be easily separated from the phosphoric acid, thereby removing the calcium portion of the phosphate rock and the sul¬fate portion of the sulfuric acid. Other acids have been used to treat phosphate rock but nitric acid is the only other acid used commercially. Nitric acid gives a mixture of phos¬phoric acid and nitrates that can be further pro¬cessed into N-P fertilizers, but the range of N/P grades that can be produced is limited. Hydrochlo¬ric acid has been used to react with phosphate rock, and it can be used to generate a pure phos¬phoric acid but only after solvent extraction to separate the calcium chloride from the phosphoric acid. And then there is the problem of what to do with the calcium chloride. The acid that has received the most attention as a substitute for sulfuric acid is phosphoric acid. In this process, the phosphoric acid reacts with the phosphate rock to give a mono-calcium phosphate solution. This process does not dissolve all the impurities in the phosphate rock, and these solids can be removed from the solution before sulfuric acid is added to convert the soluble calcium to insoluble phosphogypsum. Despite all the claimed advantages, this process has not found favor. A suc¬cessful application of this process to treat some of the lower grade phosphate rocks being used today would seem to have some distinct advantages. Other beneficiation schemes have been pro¬posed or practiced on specific phosphate rocks on a limited scale. These include calcination followed by water leaching to remove lime, weak acid

Jan 1, 1999

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By S. K. Kawatra, T. C. Eisele

Pyrite depression is of great interest in sulfide mineral flotation, where pyrite is a common gangue mineral. Since the floatability of pyrite is a function of the pH and a variety of other chemical factors, pH control is a critical part of sulfide flotation circuits. A wide variety of pyrite-depressing chemicals have been studied and used in sulfide- mineral processing, with considerable success. However, there are certain applications where there are still no satisfactory pyrite depressants, and even when suitable depressants are available, there is always a need for less-expensive reagents. Microorganisms, such as the bacteria Thiobacillus ferrooxidans, are known to depress pyrite flotation. However, the dependence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms, and the effect of pH, has been examined. Screening tests using microflotation showed that every microorganism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with two of the screened organisms and two different pyrites showed that microorganisms are very effective depressants at acid pH, but are largely ineffective at neutral and alkaline pH where the pyrite surface is not naturally hydrophobic.

Jan 1, 1994

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992