Search Documents

By John Stroiazzo, Bernard C. Aubé

Brenda Mines, located 22 km Northwest of Peachland in British Columbia, Canada was an open pit copper- molybdenum mine which closed in 1990 after 20 years of operation. The primary concern in Brenda's tailings and waste rock drainage is molybdenum at a concentration of approximately 3 mg/L. The mine drainage is alkaline and contains little or none of the typically problematic heavy metals. Given that the waters downstream are used for municipal water supply and some irrigation, a discharge limit of 0.25 ma molybdenum was imposed with specific water quality guidelines in the receiving creek. A review of all existing and potential molybdenum removal methods was undertaken prior to mine closure. The chosen process is a two-step iron co-precipitation with clarification and sand filration at a slightly acidic pH. A 4,000 usgpm (912 m3/h) treatment plant was constructed and commissioned in 1998, at a cost of $10.5M. The successful removal of molybdenum from the drainage water is explained with details on some design innovations and operational challenges encountered during plant start-up. Investigated sludge disposal options are discussed although the long term disposal scenario has not yet been finalised.

Jan 1, 2000

By R. Y. Wan, J. R. Parga, J. D. Miller

The direct recovery of precious metals from a1kaline cyanide solution is frequently accomplished by the well-established Merrill-Crowe process involving zinc-dust cementation. This is particularly true for silver. Plant data from two operations are presented and analyzed in terms of intrinsic reaction features. In such Merrill-Crowe plants a plate-and-frame filter press acts as a semicontinuous fixed-bed reactor with a distribution of particle retention times. For the plants studied, 99Yo of the silver is recovered with a solution retention time of less than 2 min. Differences in plant operating conditions and product characteristics can be related to the nature of the surface deposit of silver which forms on the zinc particles. From laboratory experiments and plant samples it has been found that the presence of lead in the system activates a change in the silver deposit morphology to the dendritic state which affects the rate of silver deposition as well as the filter cake porosity. Finally the plate-and-frame press is considered from an engineering perspective as a semi- continuous fixed - bed reactor to describe the behavior of the system.

Jan 1, 1987

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By Paul D. Kovscek, Charles D. Taylor, Edward D. Thimons

When blowing ventilation is used on a mining section, a machine-mounted scrubber is often required to maintain face dust levels below 2 mg/m3. Operation of the scrubber also affects airflow patterns at the face and the dilution of liberated methane. Reductions in scrubber flow can result in increased methane concentrations. During mining, loading of the scrubber filter with dust is likely to reduce airflow. Detecting changes in scrubber flow is difficult, especially with extended cutting, because the machine must be operated from a remote location. Tests were conducted to demonstrate how scrubber airflow could be continuously monitored at a remote location. Three variables, static pressure at the fan inlet, differential pressure across the scrubber filter, and scrubber fan motor current, were continuously monitored while the scrubber filter was incrementally loaded to reduce air flow. The results show that monitoring each variable provided a way for estimating scrubber flow.

Jan 1, 1995

By M. L. Rizzone

Since time immemorial, Mother Nature has been transporting slurries with both air and water serving as the carrier medium. Consider for example the formation of the continental shelves off our coast lines which are being formed by rivers emptying erroded land surface and depositing it into bays and gulfs. As the erosion processes take place, the fines are suspended in water which flows in streams and rivers and deposits where the velocity of the flow reduces sufficiently to allow the fines to settle out. The same process in some crude form is provided when one hoses his driveway or patio and moves dirt so as to provide a cleaning action. These examples illustrate rather crudely how the formation of slurries allows for the transport of solids. In recent years, this mechanism has become fairly well understood and slurry pipelining of many materials is now a vivid reality. The movement of liquids in pipelines necessarily occasions the use of pumps for the purpose. Those of us who have had some rub with the petroleum industry are familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well the circulating fluid utilized to remove chips which are cut by a drill bit from holes drilled deep in the earth is called drilling mud. This substance contrary to what the name might imply is usually a fairly sophisticated material designed to develop certain characteristics which are desirable in the drilling process. The particles which have been cut by the drill bit are suspended in the moving column of fluid and brought to the surface and deposited. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits. However, it is impractical to remove the fines completely from the drilling fluid and as a result they are pumped through the mud pumps back into the circulatory stream.

Jan 1, 1969

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By Murray D. Lester

The relationship between bauxite and energy has two distinct aspects. On the one hand, since virtually all of the bauxite that is mined winds up as aluminum metal, the economic health and future of the bauxite industry and of the bauxite-producing countries depend on the continuing vigour and competitiveness of aluminum against alternative metals and materials. The price of aluminum is, in turn, particularly dependent on the price of energy. Hence, the need for bauxite is ultimately affected by the price of energy. The second aspect relates to location of the bauxite industry. There is no shortage of bauxite resources in the world. For various reasons, as we shall see, there is a growing tendency toward the integration of bauxite mining, bauxite refining and aluminum smelting in those countries that have the resources both of bauxite and of energy necessary to support the entire production chain. Thus, the availability of attractive energy supplies will increasingly favour development of bauxite mining: the traditional export of bauxite as a simple raw material is likely to diminish in relative terms. In short, both the amount of bauxite mined and where this mining will take place are related to energy considerations. Let us first have a brief look at the four basic activities that are involved in our integrated operations: A. The bauxite is mined and moved to an ore plant. This step does not require more than relatively modest amounts of energy normally associated with excavation, loading and shipping of any bulk material. We need about four or five tonnes of bauxite for every tonne of metal produced.

Jan 1, 1984

By J. R. Frederick

Introduction In response to industry needs and requests, Joy Mining Machinery is aggressively evolving a "game changing" system of underground development mining machinery. This entry-development system (EDS) project is concentrated on providing clean, protected and ergonomic operator areas and a quantum leap in productivity. To meet these goals, a virtually continuous and automated mining system is needed. Operators must be able to efficiently and ergonomically perform required functions from a protected environment. Health-related issues, such as respirable dust and noise, must also be addressed. A new concept system of integrated face equipment, from the continuous miner to and including advancing the section belt and services, is needed. Phase I of the project was aimed at developing the bolting technology required. Through acquisition of Cram Australia and joint development efforts with Canyon Fuel Co., Joy now has this capability. The test platform, known as the Joy Multibolter, has successfully completed its trials at Canyon Fuel's SUFCo Mine (Fig. 1). These tests validated the bolting technology and operator protection and ergonomic issues. Phase II includes the development and testing of an integrated mining machine (IMM) capable of advancing a heading 1.5 m (5 ft) while simultaneously cutting a fullface width (single pass) and installing a complete bolt pattern. The IMM, unveiled at MINExpo 2000, incorporates the bolting technology of the Multibolter with automated full-face cutting. This machine was designed to meet Joy's stringent health, operator protection and 300m/d (1,000-ft/d) productivity goals. Phases III through V will include development of processes and integrated haulage, ventilation, power, material handling and section services advancing equipment. Processes and equipment developed will be designed for seamless integration into a complete entry development system. The focus of this paper is the new continuous miner (IMM) development, proposed testing and expectations for the EDS. The IMM is scheduled for commissioning and trials beginning in April 2001 at the SUFCo Mine. SUFCo Mine Canyon Fuel Co. is jointly owned by Arch Western Resources and the Itochu Corp. of Japan. It owns and operates three coal mines in Utah: the SUFCo Mine in Sevier County, the Skyline Mine in Carbon and Emery Counties and the Dougout Canyon Mine in Carbon County. Incorporating state-of-the-art-mining technology and advanced mine management practices, the SUFCo Mine is one of the most efficient underground coal mines in the world. The SUFCo Mine is located approximately 50-km (30 miles) northeast of Salina, UT, in the Wasatch Plateau portion of the Uinta coal basin. The mine property consists of 9,900 hm2 (24,470 acres) with approximately 118 Mt (130 million st) of recoverable reserves. Public utilities and industrial concerns purchase approximately 95% of the coal mined at SUFCo through short- or long-term contracts. Coal reserves are extracted by longwall mining, and the panels are developed using continuous miners. The longwall face at SUFCo Mine is 283-m (930-ft) wide, and the seam height ranges from 2.4 to 4 m (8 to 13 ft). The two development sections are in full operation using Joy 12CM12 continuous miners. Two super longwall panels, under development in the northeast portion of the lease block, are 4,270-m (14,000-ft) long with a 283-m (930-ft) wide longwall face. Each panel contains approximately 5.4 Mt (6 million st) of recoverable coal. SUFCo has been a world leader in productivity for a

Jan 1, 2003

By B. Pregerson, M. Gaft, J. Rabinowitz

The main phosphate minerals, apatite and francolite, are characterized by intensive selective photoluminescence, connected with impurities of Eu2+, Ce3+, V4+, Mn2+ and (UO22+ ). The non-uniform distribution of phosphate minerals in lumps makes photoluminescence sorting possible. As result, an intermediate product is recovered which is enriched by P205 and has relatively small amounts of chert, dolomite, calcite, fluorite, etc. In the case of Zin Phosphate Plant coarse rejects, for example, it is possible to separate a product enriched by francolite, practically free of chert and with a lowered calcite content. This material is suitable for flotation, with a potential 6-7 % increase yield of concentrate.

Jan 1, 1993

By Lee W. Saperstein

The Research Council of SME, at its Annual Meeting in Reno, NR, in February 1993, held a Research Forum on Technology for the Future. The Forum's purpose was to find out from the members, particularly those from industry, their opinions on research needed in the mineral industries. Panelists were selected for their breadth of knowledge and connections. Many panelists, in turn, solicited opinions from additional contacts. A similar effort is underway with mineral-oriented schools. A parallel mission has been undertaken by the American Mining Congress (AMC) through its Committee on Technology. In particular, AMC is concerned that the needs of industry be transmitted in a timely way to federal agencies, especially the US Bureau of Mines. This article reports to the SME membership the principal findings of the Research Forum. The article is derived from a full report that is available from SME. Many of the calls for research made during the Forum can be clustered into five broad categories. These categories are discussed in the following sections of this article. However, since the time of the Forum, many reviewers of the full report have noticed that fundamental research was not given much emphasis. The Research Council points out that the Forum was organized around industrial needs. There is a call to the academic and research community to organize a similar Forum. The Council emphasizes that this is not the last word on research needs and that the membership is urged to continue to give ideas and opinions to the SME Research Council. There will be an opportunity at its next meeting during the SME Annual Meeting in Albuquerque, NM, Feb. 22, 1994, for open discussion of this report. Because the opinions were intentionally confined to representatives from industry, the problems portrayed and the solutions sought are from the vantage of an operator. It comes as no surprise that many of the espoused research desiderata seek more efficient or cost-effective outcomes for the various mining activities discussed. The order of the Forum was a straightforward set of mining activities: exploration, evaluation, mining and processing.

Jan 1, 1993

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By P. Stanley Jacobsen, Hemant B. Gala, Richard E. Hucko

Coal is the nation's most abundant fossil energy resource. However, its use is limited because of the nature and amount of associated impurities, such as mineral matter, sulfur, trace elements, and moisture. The moderate-to high- sulfur content of many U.S. coals is of particular concern as current and newer, potentially more stringent, regulations require reduction in sulfur oxide emissions. Release of particulates, NOx, and other pollutants during the coal-use cycle is also of concern. The current practice of controlling sulfur oxide emissions in the major steps of the coal- use cycle is limited mainly to coal preparation by physical beneficiation and, to a smaller extent, to post-utilization cleanup (flue gas desulfurization). Approximately two-thirds of the coal from states east of the Mississippi river is physically cleaned, whereas only 15% to 20% of the operating boilers in the utility industry are equipped with scrubbers to desulfurize the flue gas (Henzel, 1988). Physical beneficiation methods can be very effective in removing mineral matter, including pyritic sulfur, from coal. These processes take advantage of the differences in physical proper- ties between coal and mineral matter to achieve the separation. In a typical physical cleaning operation, raw coal is crushed to about a 50-mm (2-inch) top size. It is then screened into coarse, intermediate, and fine sizes. Crushing the coal liberates some of the ash-forming minerals, including a portion of the sulfur that is not chemically bound to the coal. The per- centage of impurities freed from the coal matrix generally increases as the coal particle size decreases. The coarse- and intermediate-sized coals are typically subjected to a cleaning pro- cess based on differences in specific gravity between coal particles and the associated impurities. Such cleaning processes used include jigs, dense-medium baths, cyclone systems, and concentrating tables. The fine-sized (typically less than 0.5-mm) coal, if beneficiated, is typically cleaned using a froth flotation technique based on the differences in surface proper- ties between coal and its associated impurities. At fine sizes, greater cleaning potential exists because a greater portion of the impurities is released from the coal matrix. However, this potential is not fully realized owing to inefficiencies in separating fine particles using state- of-the-art flotation technology. Overall, current commercial coal preparation processes are estimated to remove up to 60% of the ash and 10% to 30% of the sulfur, depending on the coal characteristics, with product weight recoveries rang- ing from about 60% to 90% and thermal recoveries of about 85% to 98% (Versar, 1985; Science Applications International Corporation, 1987; Hoffman- Muntner Corporation, 1978). For many U.S. coals, grinding to sizes finer than those used in current coal preparation plants is required to liberate most of the physically bound impurities from the coal matrix. As noted, conventional coal-cleaning methods are not very effective at these fine sizes. Accordingly, the expanded use of domestic coal requires the development of advanced coal cleaning technologies that can provide economic performance while reducing environmental impacts. Program Goals and Objectives The overall goal of the U.S. Department of Energy (D0E)'s Coal Preparation Program is to provide the scientific and engineering knowledge base that industry can utilize to produce economically competitive and environmentally acceptable clean-coal products for introduction as market conditions warrant. The coal preparation process(es) should remove undesirable components from coal and improve its handling characteristics, thus making the product coal technically, as well as economically, viable as a competitor with petroleum-derived fuels and natural gas, and with alternative environmental control technologies. The coal preparation process must be applicable to a wide variety of bituminous and low-rank coals. The cleaning process should reduce the variability among clean-coal products from various raw coals, thus significantly increasing the range of potential end uses for each raw coal. To the extent that deeply cleaned coal products have greatly reduced levels of

Jan 1, 1988

By Paul D. Dupree

Introduction Trapper mine is a dip-line strip coal mine, located about 10 km (6 miles) southwest of Craig, CO. The mine provides the Craig Generating Station, operated by Colorado-Ute, with about 2 Mt (2.3 million st) of coal annually. The Trapper mine is situated on a hillside that climbs in elevation from 2 to 2.5 km (6500 to 7400 ft) at average grade of 15%. The coal seams dip at about 16% down-grade and they outcrop near the top of the hillside. They exceed maximum stripping depth in 1 to 1.7 km (3500 to 5500 ft) of pit length. Stripping in the three existing pits is performed with three Page 752 23 m3 (30 cu yd) walking draglines. Two of the pits are currently being cast blasted. Until the active cut, the Derringer pit was cast blasted only where the lower mined seam exceeded stripping capabilities and the pit was a single seam operation. Now, a 9-m (30-ft) interburden bench has been incorporated into the stripping plan. This bench protects the first seam of coal from shear when the overburden is cast blasted. The cast blasted section of the 1.6 km (53,000 ft) long pit has been increased from the 457 m (1500 ft) casted previ¬ously to 1 km (3500 ft). High speed films show the coal losses due to shear of the blast are minimal. The pit width in Derringer pit is 61 m (200 ft). This is necessary for efficient spoil side stripping of a relatively thin interburden in the two-seam section of the pit. The Enfield pit is entirely cast blasted. The single seam pit is 46 m (150 ft) wide, 1.1 km (3600 ft) long, and varies from 15 and 46 m (50 and 150 ft) in overburden depth. The overburden strata at the mine consists of medium-hard layers of sandstone, shale, and

Jan 1, 1987

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988

THE PENNSYLVANIA STATE UNIVERSITY, 101 MINERAL SCIENCES BUILDING UNIVERSITY PARK. PENNSYLVANIA 16803 To the Editor: With respect to the Fenvessy and Schwab article, I offer the following: As thorough as the study may be, it still has a glaring weakness. The presumption of constant supply in face of falling demand - their "low growth" case - is just wrong. It does not allow for the rapid migration, by transfer and change of major, from former high-demand programs, such as mining, to programs that have more recently obtained the cachet of job security. The figures that are shown for rapid growth in mining engineering enrollments in the period 1970-1981 are, no doubt, correct and reflect a rapid inmigration of students into mining. A similar out-migration, which began in 1982, from mining to other engineering and science disciplines is not factored into their study. Given 1983-84 enrollments, which can already be documented, it is clear that the low-growth case will, by 1985, be 50% or less of 1981. I wish students would pick their majors on the basis of their own individual abilities and interests rather than rushing lemming-like to programs that are reputed to have jobs. In the end, students will have better jobs and careers if their college majors match their talents and we, in the academic side of things, will have a livelier and more dedicated student. Lee W. Saperstein Professor and Chairman of Mining Engineering UNIVERSITY OF MISSOURI-ROLLA To the Editor: I write concerning the recent article on future demand for graduates in the mining industry. The article is, unfortunately, inaccurate because of the erroneous assumptions it makes in its basic premises. To cite but two of these, class sizes will not continue at their current level, but will, in fact, alter dramatically as a function of the perceived immediate job market rather than the future trend, so that enrollments are already below those predicted. Secondly, it is patently wrong to assume that everyone who gets a degree in the mining field will continue until retirement to work in that field. People who do not have a job in the industry will get work elsewhere and often do not come back. Others will later move to different areas. My major argument, however, deals with the underlying assumptions and methodology of the survey itself, with the concomitant challenge to the subsequent conclusions. It is no great secret that the technological world is undergoing a dramatic revolution. Computer use is rapidly spreading to the point where the microcomputer will be an integral part of every mine engineer's desk. Such a tool, which for optimal benefit must be operated by knowledgeable mining engineers, will make mining much more of a science than the current level. To remain competitive, mines will increasingly rely on higher level deci-

Jan 1, 1984

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By N. J. Peberdy, C. N. Moreton, K. C. Garner

Introduction During the past decade a major objective of the process industry has been to use digital computer technology to improve plant operating efficiencies. This objective implied some form of optimization, a concept that has various interpretations depending on the view of the prospective user. For the purpose of this paper, optimization of a process plant is defined as the establishment and setting of plant operating conditions that maximize some mathematical yield function, i.e. maximum profit, minimum residue, etc. Analysis of these objectives and the available design and implementation techniques led to the conclusion that digital computer and optimization techniques are not the stumbling blocks, but rather the development and derivation of the mathematical models of the unit operations and process plants to be optimized. Such models should not only describe the optimized (steady-state) objective, but also how one steers to this state (control algorithm). Due to the multidisciplinary nature of the skills associated with the design and operation of process plants, the development of suitable models by a single discipline, such as the process control engineer, was found to be not only difficult but often impossible, due to budget and human resource limitations. To over-come these limitations, a computer aided design (CAD) tool has been developed. It aims to provide a productivity tool to the various disciplines, at the same time coordinating the technical input from each. The system described is but the starting point in an evolutionary development of a tool that, with use, is becoming more efficient and cost effective to use. Development has become an application engineering activity rather than the preserve of the computer specialist. Project phasing The development of a mathematical description of a process plant requires coordination of information from conceptual design to operation management. The activities required to build and operate a process plant are divided into four basic chronological activities or phases. These activities are often undertaken by different organizations and disciplines. As a result, continuity is often lost with the resultant loss of critical design data. The major activities are considered to be: conceptual and flowsheeting; detailing around the P & ID; building and commissioning; and plant operation. The CAD system described provides a design tool to be used for each of these activities, as well as providing continuity between the activities and the disciplines involved. The heart of the system is the dynamic simulation of the flowsheet. Each of the activities will be discussed, leading to two simple examples that demonstrate the use of the simulator. Figure 1 shows a schematic format of the various activities and the path followed by the dynamic flowsheet simulator in the life of a project. Flowsheet development The prime requirements in the design and develop¬ment of a process flowsheet are • selection of the correct unit operations to achieve the most economic (capital and operating) beneficiation of the specified reserve ; • the sizing of the unit operations to achieve the desired results, as a function of the projected feed rates etc., to handle the time related (dynamics) of the process; and • the production of a set of engineering documents showing the drawn and labeled flowsheet with an equipment list and process specification for each of the unit operations. The question may well be asked at this stage why dynamic flowsheet simulation should be considered when steady state modeling has been found to be adequate to date. With the increases encountered in the cost of capital, one often cannot afford the luxury of designing around the compounding worst case technique. Further, a more accurate design of the control surges can be achieved. No information is lost in that the steady state solution is in fact a subset of the dynamic model. In generalized state space modeling, the differential equations describing the process dynamics are illustrated in the following matrix notation: XDOT=A.X+B.U(1) Y =C.X+D.U(2) where XDOT describes the set of first order derivatives of the system state Vector, and X- is the system state Vector; A - is the system matrix operator which in the general nonlinear case is both a function of X and time ; U- is the process input vector; B - is the input mapping matrix; Y - is the set of observations; C - is the output mapping matrix which maps X - onto Y; and D- maps the input onto the observations. Thus, by time integration of the system dynamic equations, described in (1), the dynamic trajectory away from any set of initial conditions can be deter¬mined. Further, by finding the conditions at which XDOT = 0, the steady state solution can be determined.

Jan 1, 1987

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987