Search Documents

By S. Hearn, S. Boskovic, A. Smethurst

"The digestion of minerals in strong acids or at elevated temperatures can result in the release of large amounts of silicic acid which can polymerize in solution to form colloidal silica and gels. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Huntsman’s POLYSIL® polyether coagulants have a “lock and key” relationship with the surface of colloidal silica to help lower the concentration of these particles in solution, improve process efficiency and reduce reagent losses by minimizing crud formation. This paper investigates some of the issues caused by colloidal silica in hydrometallurgy processes and illustrates how the use of POLYSIL® coagulants has helped to improve process outcomes. INTRODUCTION Coagulation differs from flocculation in a number of ways. Coagulants are relatively small molecules that modify the surfaces of fine particles, weakening repulsive forces between them and allowing particles to stick together, while flocculants are generally molecules that are large enough to bridge the boundary layers between the particles. With flocculation, addition rate and mixing all make a difference to the flocs formed. Coagulation, on the other hand, is an equilibrium process. With coagulation it is only necessary to achieve good mixing, and coagulates will form as Brownian motion pushes the particles into each other. In real systems, this process is complete within seconds. Huntsman’s POLYSIL® polyether based coagulants have a strong affinity with the surface of colloidal silica formed by the polymerization of silicic acid. While silica found in minerals has a low aqueous solubility, large amounts of silica as silicic acid can be released as these minerals are digested in strong acids at elevated temperatures. The solubility of free silicic acid is about 150 ppm under pH conditions typical in acid leach environments (1), so the bulk of the silica will polymerize in solution to form colloidal silica. Colloidal silica can pass through a hydrometallurgy process without affecting any of the operations. However, it can cause a number of problems. These include gelling in a leach, interfering with flocculation or crystallization, initiating crud formation (2,3,4), decreasing extraction kinetics and increasing phase disengagement times (5,6) in solvent extraction. In these cases, coagulating the silica with POLYSIL® coagulants can reduce or eliminate the problem by enabling these particles to be flocculated and removed from the solution."

Jan 1, 2015

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By Emily Wortman-Wunder

As the 2010 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2010 issue of Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 328. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable transfer of technology. Communication within the mining community is the key to a successful society. Through books, magazines, meetings and electronic media, we accomplish the technology exchange that is fundamental to the existence of the Society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, Pennsylvania, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume certainly fulfills that pledge. The 2010 Transactions is the first Transactions to take advantage of new publication technologies. It appears solely as an e-book. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will certainly better serve the mining community. I am excited about this development and the opportunities it presents. The 2010 Transactions also contain some of the most exciting research from the past year, including new developments in mineral processing, safety and exploration. Be sure not to miss the two Minerals & Metallurgical Processing issues on the subject of gold hydrometallurgy. This 2010 Transactions comprise of a total of 78 technical papers (582 pages including index), including all 21 papers (136 pages) that were published in 2010 in the Technical Papers Section of Mining Engineering magazine (Vol. 62) and all 34 papers (231 pages) that were published in 2010 in Minerals & Metallurgical Processing (Vol. 27). Addition, this volume contains 23 papers (194 pages) that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 78 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2010 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2010

By Fred A. Glover

It's a pleasure to be included with this group. I am not here to sell my services, but rather to share with you some ideas and considerations on using environmental consultants. Environmental consultants have developed some problems as well as created new costs for companies that are as legitimate as engineering costs. Each day the mining industry is becoming more affected by the proliferation of environmental regulations and their interpretations by federal and state agencies. How does a modern mining company cope with all the demands for environmental consideration by regulatory agencies and special interest environmental groups-- yet produce a product and make a profit? One way is to make efficient use of environmental consultants. But, as everyone here knows, this approach has been fraught with seemingly inherent frustrations, difficulties, and much justified criticism.

Jan 1, 1979

By N. K. Dumakor-Dupey, G. B. Sakyi-Addo, K. J. Bansah

"Artisanal and small-scale mining (ASM) occurs in many countries around the world, and provides a source of livelihood to many impoverished local people in areas where it occurs. This paper reports the role of female participants and reasons why they engage in ASM. Field visits were made to 12 ASM sites located in the Tarkwa Mining District of Ghana to conduct interviews with male diggers and female participants. It was observed that over 100 women between the ages of 18 and 50 participate in ASM for survival. They engage in ASM largely because they have no alternative employable skills and income sources. These female participants depend on ASM to sustain the lives of their dependents. INTRODUCTION Artisanal and small-scale mining (ASM) conventionally involves use of rudimentary tools (such as picks, shovels, chisels and hammers) to exploit precious minerals and metals from the ground. It has been a major source of livelihood to many impoverished local people for more than a century. In many instances, it is the only source of income to indigenous people who have no alternative employable skills. The World Bank estimated that more than 100 million people around the world benefit from ASM which largely occurs in developing countries in Asia, Africa, Oceania, and South and Central America (World Bank, 2013). Cobalt, which is used in lithium-ion batteries to power cellphones, laptop computers, and electric vehicles, is largely produced by artisanal miners in Congo (The Washington Post, 2016). In Sudan, ASM is a significant contributor to the national economy, accounting for about 85% of total gold extracted yearly from 2010 to 2015 (Ibrahim, 2015). Also, according to the Embassy of Sierra Leone in Washington DC, USA, 90% of mineral export in Sierra Leone can be attributed to thriving artisanal diamond mining in the country (Sierra Leone Embassy, 2016). In Ghana, the ASM sector was recognized by government as a multimillion industrial activity, and through a series of initiatives, it was legalized by promulgating the Small Scale Gold Mining Law of 1989 (PNDCL 218). Presently, artisanal mining is widely practiced in two forms: licensed (registered), sometimes referred to as formal ASM, and unregistered (informal or illegal) operations, popularly called “galamsey”, a name believed to have been derived from “gather and sell” by ancient miners who could not communicate in the English language with European/British miners. The ASM sector in Ghana, like other countries, has seen a rise in female participation over the years. A report by the International Labour Organization (ILO) indicated that women account for about 15% of total workforce in ASM in Ghana, and up to 50% in Africa (ILO, 1999). Other researchers have also estimated women participants in ASM to be between 30 and 70% in Africa (Hinton et al., 2003a; Hinton et al. 2003b; Hilson, 2002). Presently, there is no reliable data from Ghanaian authorities on number of females engaged in ASM. However, data obtained from 15 ASM sites suggest that at least 40% of the employees are women. It is expected that a similar trend exists across ASM operations in Ghana."

Jan 1, 2017

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1. Dump leaching, where the ore is moved from its original location to be leached at another site. 2. In situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains.

Jan 1, 1969

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

Most statistical and geostatistical methods of re-source and reserve estimation work extremely well for Normal (Gaussian) well-behaved information. However, most interesting mineral deposits exhibit far from this idealistic distribution of values. It seems that the more valuable the mineral, the less likely the data are to have a Normal distribution. Values tend to be "positively skewed" with a long tail into the high values. Using averaging techniques, such as inverse distance or ordinary kriging may result in consider-able overestimation of grades and tonnages unless such values are cut or otherwise modified. This paper presents some real case studies where distributions are (a) highly skewed and (b) the product of multiple phases of mineralisation. Practical methods are presented for solving such problems including combinations of indicator and log normal kriging methods. The emphasis of the presentation is on developing operational methods which can be used on project evaluation or grade control in producing mines.

Jan 1, 2000

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By Howard L. Hartman

The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry is not unaffected by the drought: not only is research lagging, but hard- pressed universities are going to the private sector for funding. This paper's thesis is not that mining companies should shower universities with philanthropy, but that a quid pro quo ought to be exacted: a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that may lend itself to adoption by our industry.

Jan 1, 1984

By James F. Fraser

Construction of a major linear project in any environment is difficult, at best. Construction of a major linear project which includes major subway elements, both cut and cover and tunneling, in the center of an urban environment, approaches the impossible. I believe such a project would be impossible for a private company or a privately owned utility for a variety of reasons. The major two reasons are the funding necessary for such massive projects and the myriad of individual interests associated with private ownership of land. Such projects are possible in the public sector only because the need for the project... as is the case with mass transportation in Atlanta. . .overrides the profit motive. Without the profit motive, private companies, whether utilities or not, are precluded from practical interest in the development of any project. While it is safe to conclude that a profit-oriented business would have no practical interest in developing such massive projects as may include major tunnels, it would be useful, I think, to compare some of the significant differences between private profit-oriented businesses, and an agency, or Authority, such as MARTA, in building a major linear project. SLIDE 1. Comparison of a Private Company and a Public Agency [Item Private Company Public Agency Simplified To make a profit To provide a pre Purpose scribed service]

Jan 1, 1979

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

During the past 20 years, FKC-Lake Shore, located in southern Indiana, has been working with Contitech, the German conveyor company, to push vertical conveyor technology to new depths and open up additional opportunities for underground mine owners. Historically, the underground mining industry has largely been unable to realize the benefits of these efficient systems due to the design limitations in maximum depth and capacity. Until recently, only relatively shallow depth mines with low production rates have been a ?t for a vertical conveyor system. This, however, is changing with technical advancements in the Pocketlift system. With each milestone, a new vertical conveyor record is set for depth and capacity. For instance, in 2002, FKC-Lake Shore set one such record with the installation of a Pocketlift system at a mine in the Illinois coal basin with a lift height of 273 m (896 ft) and a production rate of 1.8 kt/h (2,000 stph). Although it was unthinkable at that time, today?s vertical conveyors are capable of reaching lift heights up to 700 m (2,300 ft) with an average production rate of 450 t/h (500 stph). These new lift heights and production rates are opening the technology to more potential mine owners and shifting the way people look at moving material in the future.

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By William H. Bird

Over the past 14 years, the efforts of 2 companies and several individuals have outlined a major solfataric gold ore body in the Summitville district in the southeast San Juan Mountains of Colorado. The hard work of these years could not have flowered without a dedication to modern exploration methods, an intense interest in new theories of ore genesis, and a relentless discontent with the accepted geology of the Summitville area. To set the stage for this discovery period, it must be noted that it began 100 years after gold was first found at Summitville. It was the height of the "porphyry copper" era and gold was still not a part of the explorationists' portfolio. It was also a time of great intellectual stimulation. Theories were rapidly developing to relate different types of ore deposition and to place ore genesis within the fabric of plate tectonics. Summitville itself had just been linked to the newly discovered Platoro caldera complex and the Platoro lineament. This in turn related Summitville to the other San Juan volcanic field caldera ore deposits.

Jan 1, 1990